This is actually against the CVS. Basically what is there now only allows
for the SYM53C8XX driver to be configured. This patch is taken directly
from drivers/scsi/Config.in and allows for both or either one to be
configured (notably, the current way wouldn't allow my U30 to boot using
the SYM53C8XX driver).
2.3.36 seems to have the same problem.
--
-----------=======-=-======-=========-----------=====------------=-=------
/ Ben Collins -- ...on that fantastic voyage... -- Debian GNU/Linux \
` [EMAIL PROTECTED] -- [EMAIL PROTECTED] -- [EMAIL PROTECTED] '
`---=========------=======-------------=-=-----=-===-======-------=--=---'
diff -u -r1.67.2.6 config.in
--- linux-2.2/arch/sparc64/config.in~ 1999/12/23 01:47:12 1.67.2.6
+++ linux-2.2/arch/sparc64/config.in 2000/01/04 12:17:25
@@ -175,17 +175,24 @@
bool ' Collect statistics to report in /proc' CONFIG_AIC7XXX_PROC_STATS N
int ' Delay in seconds after SCSI bus reset' CONFIG_AIC7XXX_RESET_DELAY
5
fi
- dep_tristate 'SYM53C8XX SCSI support' CONFIG_SCSI_SYM53C8XX $CONFIG_SCSI
- if [ "$CONFIG_SCSI_NCR53C8XX" != "n" ]; then
- int ' default tagged command queue depth'
CONFIG_SCSI_NCR53C8XX_DEFAULT_TAGS 8
- int ' maximum number of queued commands' CONFIG_SCSI_NCR53C8XX_MAX_TAGS
32
- int ' synchronous transfers frequency in MHz' CONFIG_SCSI_NCR53C8XX_SYNC
10
- bool ' enable profiling' CONFIG_SCSI_NCR53C8XX_PROFILE
- if [ "$CONFIG_SCSI_NCR53C8XX_DEFAULT_TAGS" = "0" ]; then
- bool ' not allow targets to disconnect'
CONFIG_SCSI_NCR53C8XX_NO_DISCONNECT
- fi
- if [ "$CONFIG_EXPERIMENTAL" = "y" ]; then
- bool ' assume boards are SYMBIOS compatible'
CONFIG_SCSI_NCR53C8XX_SYMBIOS_COMPAT
+ if [ "$CONFIG_SCSI_NCR53C7xx" != "y" ]; then
+ dep_tristate 'NCR53C8XX SCSI support' CONFIG_SCSI_NCR53C8XX $CONFIG_SCSI
+ dep_tristate 'SYM53C8XX SCSI support' CONFIG_SCSI_SYM53C8XX $CONFIG_SCSI
+ if [ "$CONFIG_SCSI_NCR53C8XX" != "n" -o "$CONFIG_SCSI_SYM53C8XX" != "n" ];
+then
+ int ' default tagged command queue depth'
+CONFIG_SCSI_NCR53C8XX_DEFAULT_TAGS 8
+ int ' maximum number of queued commands'
+CONFIG_SCSI_NCR53C8XX_MAX_TAGS 32
+ int ' synchronous transfers frequency in MHz'
+CONFIG_SCSI_NCR53C8XX_SYNC 20
+ bool ' enable profiling' CONFIG_SCSI_NCR53C8XX_PROFILE
+ bool ' use normal IO' CONFIG_SCSI_NCR53C8XX_IOMAPPED
+ if [ "$CONFIG_SCSI_SYM53C8XX" != "n" ]; then
+ bool ' include support for the NCR PQS/PDS SCSI card'
+CONFIG_SCSI_NCR53C8XX_PQS_PDS
+ fi
+ if [ "$CONFIG_SCSI_NCR53C8XX_DEFAULT_TAGS" = "0" ]; then
+ bool ' not allow targets to disconnect'
+CONFIG_SCSI_NCR53C8XX_NO_DISCONNECT
+ fi
+ if [ "$CONFIG_EXPERIMENTAL" = "y" ]; then
+ bool ' assume boards are SYMBIOS compatible'
+CONFIG_SCSI_NCR53C8XX_SYMBIOS_COMPAT
+ fi
fi
fi
dep_tristate 'Qlogic ISP SCSI support' CONFIG_SCSI_QLOGIC_ISP $CONFIG_SCSI
