Hi guys, Is there any chance that one day it will be possible to see O2 sample on a CCR dive? On Thu, 10 May 2018 at 22:48, Davide DB <dbdav...@gmail.com> wrote:
> On Thu, 3 May 2018 at 21:39, Davide DB <dbdav...@gmail.com> wrote: > > On Thu, 3 May 2018 at 18:52, Anton Lundin <gla...@acc.umu.se> wrote: > >> On 03 May, 2018 - Davide DB wrote: > >> > On Thu, 3 May 2018 at 13:15, Anton Lundin <gla...@acc.umu.se> wrote: > >> > > >> > > On 03 May, 2018 - Davide DB wrote: > >> > > > >> > > > On Wed, 2 May 2018 at 11:04, Anton Lundin <gla...@acc.umu.se> > wrote: > >> > > > > >> > > > > > >> > > > > Try to download them into a fresh logbook with the current > desktop > >> > > > > version, to see what's happens then. > >> > > > > > >> > > > > >> > > > I've just downloaded my dives on a fresh Win10 4.7.8 installation. > >> > > > As usual after few dives my Petrel quits with "error sending packet > >> > > error". > >> > > > I saved some of them anyway and PO2 values are missing. > >> > > > This is how the petrel controller is recognized. File is attached. > >> > > > > >> > > > <divecomputer model='Shearwater Petrel 2' deviceid='1a2d46b1' > >> > > > diveid='2e7067fb' dctype='CCR'> > >> > > > > >> > > > There's no mention of O2 sensor. > >> > > > > >> > > > These are all different pertel descriptions of the very same dive > >> > > computer > >> > > > I found in my original logbook > >> > > > > >> > > > <divecomputer model='Shearwater Petrel 2' deviceid='1a2d46b1' > >> > > > diveid='3db7eb77' dctype='CCR' no_o2sensors='1'> > >> > > > <divecomputer model='Shearwater Petrel 2' deviceid='1a2d46b1' > >> > > > diveid='52d4ba3e' dctype='CCR' no_o2sensors='3'> > >> > > > <divecomputer model='Shearwater Petrel' deviceid='1a2d46b1' > >> > > > diveid='a6e05a10' dctype='CCR'> > >> > > > <divecomputer model='Shearwater Petrel 2' deviceid='1a2d46b1' > >> > > > diveid='3db24900' dctype='CCR'> > >> > > > > >> > > > Were pO2 samples download removed? > >> > > > >> > > This is probably because we can't find any calibration values in your > >> > > computer. Did you get a warning: > >> > > "Disabled all O2 sensors due to a default calibration value." ? > >> > > > >> > > I think the code should fall back to the sensor average po2 when we > >> > > won't get calibration values for the sensors, but we're not doing > that > >> > > right now. > >> > > > >> > > >> > Anton, > >> > > >> > I'm not crazy enough to dive a rebreather without a proper calibration. > >> > Everything is ok on my unit. Cells are new and get calibrated before > every > >> > dive. > >> Shure. The computer is probably properly calibrated, but the > >> calibration values found in the memory of the computer are the default > >> ones. Without those we can't convert the mV values to po2 values. > >> The cal values might be there somewhere, but we don't know where. > >> We can't emit the raw mV values, because neither libdivecomputer nor > >> subsurface supports mV values. > >> > I tried to download again from Shearwater desktop and everything is > there: > >> > pO2 and mV samples. I've never updated my Petrel since we found that > >> > Subsurface pO2 values were completely wrong so I guess it should be > some > >> > bug arose lately. > >> > It's sad nobody else (ccr users) replied to my feedback request when I > >> > noted the pO2 discrepancy. I cannot believe I'm the only one on this > list > >> > using a ccr unit whit a divecan shearwater controller. > >> > When I realized pO2 were missing I thought it was something related > to the > >> > mobile download but it's not. > >> > > >> > I would do a full Subsurface download but I drained another battery > but I > >> > do not have a new one around ATM. > >> We should at least emit the per sample average, when we can't emit the > >> individual sensor values. > >> Best would be if we could emit both the "true" average po2 and the > >> individual sensor values. Unfortunately the interface doesn't support > >> that distinction. > > I changed battery and downloaded again with subsurface 4.7.8 desktop > saving the libdivecomputer log file. > > I quit the download before getting errors and draining my battery. > > At the end of the libdivecomputer file I find: > > WARNING: Disabled all O2 sensors due to a default calibration value. [in /home/travis/build/Subsurface-divelog/subsurface/libdivecomputer/src/shearwater_predator_parser.c:503 > (shearwater_predator_parser_cache)] > > INFO: Write: size=9, data=FF0105002E902000C0 > > Exactly the problem mentioned by Anton. > > Could someone explain me what does it means? > > Is it a way to avoid displaying wrong pO2 samples due to the previous > problem? > > What can I do? Is it my fault? Is my Petrel defective? > > Why in my logbook I find 4 different computer names with different > attributes if my unit is always the same? > > <divecomputer model='Shearwater Petrel 2' deviceid='1a2d46b1'> > diveid='3db7eb77' dctype='CCR' no_o2sensors='1'> > > <divecomputer model='Shearwater Petrel 2' deviceid='1a2d46b1'> > diveid='52d4ba3e' dctype='CCR' no_o2sensors='3'> > > <divecomputer model='Shearwater Petrel' deviceid='1a2d46b1'> > diveid='a6e05a10' dctype='CCR'> > > <divecomputer model='Shearwater Petrel 2' deviceid='1a2d46b1'> > diveid='3db24900' dctype='CCR'> > > Are those differences due to subsurface history reason? > > Thank you in advance > > -- > > Davide > > https://vimeo.com/bocio/videos > Thank you guys > -- > Davide -- Davide https://vimeo.com/bocio/videos _______________________________________________ subsurface mailing list subsurface@subsurface-divelog.org http://lists.subsurface-divelog.org/cgi-bin/mailman/listinfo/subsurface
