Have you tried to change the modes of the controller in BIOS ?
Like native vs. legacy mode and RAID mode vs. SATA mode etc ?
The ICH7 support of FreeBSD might also be to blame. I'm not sure how good it
is atm.
-lsf
-----Original Message-----
From: news [mailto:[EMAIL PROTECTED] On Behalf Of Lynn A. Roth
Sent: 1. november 2005 21:12
To: support@pfsense.com
Subject: [pfSense Support] Re: Trouble installing to Dell PowerEdge 850
Here is dmesg -a after booting verbose. The drive is connected to
Channel 0 on the SATA controller.
Lynn
P:
ID: 0x00000000 VER: 0x00050014 LDR: 0x01000000 DFR: 0x0fffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000100ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010000
crypto: <crypto core>
ath_rate: version 1.2 <SampleRate bit-rate selection algorithm>
wlan: <802.11 MAC ACL support>
wlan: mac acl policy registered
wlan: <802.11 Link Layer>
mem: <memory>
Pentium Pro MTRR support enabled
nfslock: pseudo-device
null: <null device, zero device>
io: <I/O>
random: <entropy source, Software, Yarrow>
ath_hal: 0.9.16.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413,
RF5413, DFS)
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <DELL PE850> on motherboard
acpi0: [MPSAFE]
pci_open(1): mode 1 addr port (0x0cf8) is 0x80000090
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=27788086)
pcibios: BIOS version 2.10
Found $PIR table, 9 entries at 0xc00fb840
PCI-Only Interrupts: none
Location Bus Device Pin Link IRQs
embedded 0 1 A 0x60 3 4 5 6 10 11 14 15
embedded 0 29 A 0x68 3 4 5 6 10 11 14 15
embedded 0 29 B 0x69 3 4 5 6 10 11 14 15
embedded 0 29 C 0x6a 3 4 5 6 10 11 14 15
embedded 0 29 D 0x6b 3 4 5 6 10 11 14 15
embedded 0 28 A 0x69 3 4 5 6 10 11 14 15
embedded 0 28 B 0x6a 3 4 5 6 10 11 14 15
embedded 0 28 C 0x6b 3 4 5 6 10 11 14 15
embedded 0 28 D 0x63 3 4 5 6 10 11 14 15
embedded 0 31 A 0x60 3 4 5 6 10 11 14 15
embedded 0 31 B 0x62 3 4 5 6 10 11 14 15
embedded 0 31 C 0x68 3 4 5 6 10 11 14 15
embedded 0 31 D 0x63 3 4 5 6 10 11 14 15
embedded 5 0 A 0x60 3 4 5 6 10 11 14 15
embedded 5 0 B 0x61 3 4 5 6 10 11 14 15
embedded 5 0 C 0x62 3 4 5 6 10 11 14 15
embedded 5 0 D 0x63 3 4 5 6 10 11 14 15
embedded 6 0 A 0x61 3 4 5 6 10 11 14 15
embedded 6 0 B 0x62 3 4 5 6 10 11 14 15
embedded 6 0 C 0x63 3 4 5 6 10 11 14 15
embedded 6 0 D 0x60 3 4 5 6 10 11 14 15
slot 1 2 0 A 0x60 3 4 5 6 10 11 14 15
slot 1 2 0 B 0x61 3 4 5 6 10 11 14 15
slot 1 2 0 C 0x62 3 4 5 6 10 11 14 15
slot 1 2 0 D 0x63 3 4 5 6 10 11 14 15
slot 2 1 0 A 0x60 3 4 5 6 10 11 14 15
slot 2 1 0 B 0x61 3 4 5 6 10 11 14 15
slot 2 1 0 C 0x62 3 4 5 6 10 11 14 15
slot 2 1 0 D 0x63 3 4 5 6 10 11 14 15
embedded 7 5 A 0x63 3 4 5 6 10 11 14 15
AcpiOsDerivePciId: bus 0 dev 31 func 0
AcpiOsDerivePciId: bus 0 dev 31 func 0
acpi0: Power Button (fixed)
pci_link0: <ACPI PCI Link LNKA> irq 5 on acpi0
pci_link0: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 5 N 0 3 4 5 6 7 9 10 11 12
pci_link0: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 5 N 0 3 4 5 6 7 9 10 11 12
pci_link0: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12
pci_link1: <ACPI PCI Link LNKB> irq 3 on acpi0
pci_link1: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 3 N 0 3 4 5 6 7 9 10 11 12
pci_link1: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 3 N 0 3 4 5 6 7 9 10 11 12
pci_link1: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12
pci_link2: <ACPI PCI Link LNKC> on acpi0
pci_link2: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12
pci_link2: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12
pci_link2: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12
pci_link3: <ACPI PCI Link LNKD> on acpi0
pci_link3: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12
pci_link3: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12
pci_link3: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12
pci_link4: <ACPI PCI Link LNKE> irq 11 on acpi0
pci_link4: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 11 N 0 3 4 5 6 7 9 10 11 12
pci_link4: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 11 N 0 3 4 5 6 7 9 10 11 12
pci_link4: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12
pci_link5: <ACPI PCI Link LNKF> irq 10 on acpi0
pci_link5: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 10 N 0 3 4 5 6 7 9 10 11 12
pci_link5: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 10 N 0 3 4 5 6 7 9 10 11 12
pci_link5: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12
pci_link6: <ACPI PCI Link LNKG> irq 6 on acpi0
pci_link6: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 6 N 0 3 4 5 6 7 9 10 11 12
pci_link6: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 6 N 0 3 4 5 6 7 9 10 11 12
pci_link6: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12
pci_link7: <ACPI PCI Link LNKH> on acpi0
pci_link7: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12
pci_link7: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12
pci_link7: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12
ACPI timer: 1/0 1/0 1/0 1/0 1/0 1/0 1/0 1/0 1/0 1/0 -> 10
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <ACPI CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
found-> vendor=0x8086, dev=0x2778, revid=0x00
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x2090, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x2779, revid=0x00
bus=0, slot=1, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0047, statreg=0x0010, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x07 (1750 ns), maxlat=0x00 (0 ns)
intpin=a, irq=255
found-> vendor=0x8086, dev=0x27d0, revid=0x01
bus=0, slot=28, func=0
class=06-04-00, hdrtype=0x01, mfdev=1
cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x06 (1500 ns), maxlat=0x00 (0 ns)
intpin=a, irq=255
found-> vendor=0x8086, dev=0x27e0, revid=0x01
bus=0, slot=28, func=4
class=06-04-00, hdrtype=0x01, mfdev=1
cmdreg=0x0047, statreg=0x0010, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x07 (1750 ns), maxlat=0x00 (0 ns)
intpin=b, irq=255
found-> vendor=0x8086, dev=0x27e2, revid=0x01
bus=0, slot=28, func=5
class=06-04-00, hdrtype=0x01, mfdev=1
cmdreg=0x0047, statreg=0x0010, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x07 (1750 ns), maxlat=0x00 (0 ns)
intpin=c, irq=255
found-> vendor=0x8086, dev=0x27c8, revid=0x01
bus=0, slot=29, func=0
class=0c-03-00, hdrtype=0x00, mfdev=1
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
map[20]: type 4, range 32, base 0000ace0, size 5, enabled
pcib0: matched entry for 0.29.INTA
pcib0: slot 29 INTA hardwired to IRQ 20
found-> vendor=0x8086, dev=0x27c9, revid=0x01
bus=0, slot=29, func=1
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=10
map[20]: type 4, range 32, base 0000acc0, size 5, enabled
pcib0: matched entry for 0.29.INTB
pcib0: slot 29 INTB hardwired to IRQ 21
found-> vendor=0x8086, dev=0x27ca, revid=0x01
bus=0, slot=29, func=2
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=c, irq=6
map[20]: type 4, range 32, base 0000aca0, size 5, enabled
pcib0: matched entry for 0.29.INTC
pcib0: slot 29 INTC hardwired to IRQ 22
found-> vendor=0x8086, dev=0x27cc, revid=0x01
bus=0, slot=29, func=7
class=0c-03-20, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D3 current D0
map[10]: type 1, range 32, base feb00400, size 10, enabled
pcib0: matched entry for 0.29.INTA
pcib0: slot 29 INTA hardwired to IRQ 20
found-> vendor=0x8086, dev=0x244e, revid=0xe1
bus=0, slot=30, func=0
class=06-04-01, hdrtype=0x01, mfdev=0
cmdreg=0x0147, statreg=0x0010, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x0b (2750 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x27b8, revid=0x01
bus=0, slot=31, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0147, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x27df, revid=0x01
bus=0, slot=31, func=1
class=01-01-8a, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0288, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=255
map[20]: type 4, range 32, base 0000fc00, size 4, enabled
found-> vendor=0x8086, dev=0x27c0, revid=0x01
bus=0, slot=31, func=2
class=01-01-8f, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x02b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=c, irq=11
powerspec 2 supports D0 D3 current D0
map[10]: type 4, range 32, base 0000ac98, size 3, enabled
map[14]: type 4, range 32, base 0000ac90, size 2, enabled
map[18]: type 4, range 32, base 0000ac80, size 3, enabled
map[1c]: type 4, range 32, base 0000ac78, size 2, enabled
map[20]: type 4, range 32, base 0000ac60, size 4, enabled
map[24]: type 1, range 32, base feb00000, size 10, enabled
pcib0: matched entry for 0.31.INTC
pcib0: slot 31 INTC hardwired to IRQ 20
found-> vendor=0x8086, dev=0x27da, revid=0x01
bus=0, slot=31, func=3
class=0c-05-00, hdrtype=0x00, mfdev=0
cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=255
map[20]: type 4, range 32, base 000008c0, size 5, enabled
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xf000-0xfff
pcib1: memory decode 0xfff00000-0xfffff
pcib1: prefetched decode 0xfff00000-0xfffff
pci1: <ACPI PCI bus> on pcib1
pci1: physical bus=1
pcib2: <ACPI PCI-PCI bridge> at device 28.0 on pci0
pcib2: secondary bus 2
pcib2: subordinate bus 4
pcib2: I/O decode 0xe000-0xefff
pcib2: memory decode 0xfe800000-0xfeafffff
pcib2: prefetched decode 0xfff00000-0xfffff
pci2: <ACPI PCI bus> on pcib2
pci2: physical bus=2
found-> vendor=0x8086, dev=0x0340, revid=0x09
bus=2, slot=0, func=0
class=06-04-00, hdrtype=0x01, mfdev=1
cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x06 (1500 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x0341, revid=0x09
bus=2, slot=0, func=2
class=06-04-00, hdrtype=0x01, mfdev=1
cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x06 (1500 ns), maxlat=0x00 (0 ns)
pcib3: <PCI-PCI bridge> at device 0.0 on pci2
pcib3: secondary bus 3
pcib3: subordinate bus 3
pcib3: I/O decode 0xe000-0xefff
pcib3: memory decode 0xfe900000-0xfeafffff
pcib3: prefetched decode 0xfff00000-0xfffff
pci3: <PCI bus> on pcib3
pci3: physical bus=3
found-> vendor=0x8086, dev=0x108a, revid=0x03
bus=3, slot=4, func=0
class=02-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0117, statreg=0x0230, cachelnsz=16 (dwords)
lattimer=0x40 (1920 ns), mingnt=0xff (63750 ns), maxlat=0x00 (0 ns)
intpin=a, irq=5
powerspec 2 supports D0 D3 current D0
MSI supports 1 message, 64 bit
map[10]: type 1, range 64, base fe9e0000, size 17, enabled
pcib3: (null) requested memory range 0xfe9e0000-0xfe9fffff: good
pcib2: (null) requested memory range 0xfe9e0000-0xfe9fffff: good
map[20]: type 4, range 32, base 0000ecc0, size 6, enabled
pcib3: (null) requested I/O range 0xecc0-0xecff: in range
pcib2: (null) requested I/O range 0xecc0-0xecff: in range
pcib2: matched entry for 2.0.INTA
pcib2: slot 0 INTA hardwired to IRQ 16
pcib3: slot 4 INTA is routed to irq 16
found-> vendor=0x8086, dev=0x108a, revid=0x03
bus=3, slot=4, func=1
class=02-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0117, statreg=0x0230, cachelnsz=16 (dwords)
lattimer=0x40 (1920 ns), mingnt=0xff (63750 ns), maxlat=0x00 (0 ns)
intpin=b, irq=3
powerspec 2 supports D0 D3 current D0
MSI supports 1 message, 64 bit
map[10]: type 1, range 64, base fe9c0000, size 17, enabled
pcib3: (null) requested memory range 0xfe9c0000-0xfe9dffff: good
pcib2: (null) requested memory range 0xfe9c0000-0xfe9dffff: good
map[20]: type 4, range 32, base 0000ec80, size 6, enabled
pcib3: (null) requested I/O range 0xec80-0xecbf: in range
pcib2: (null) requested I/O range 0xec80-0xecbf: in range
pcib2: matched entry for 2.0.INTB
pcib2: slot 0 INTB hardwired to IRQ 17
pcib3: slot 4 INTB is routed to irq 17
em0: <Intel(R) PRO/1000 Network Connection, Version - 2.1.7> port
0xecc0-0xecff mem 0xfe9e0000-0xfe9fffff irq 16 at device 4.0 on pci3
em0: Reserved 0x20000 bytes for rid 0x10 type 3 at 0xfe9e0000
em0: Reserved 0x40 bytes for rid 0x20 type 4 at 0xecc0
em0: [MPSAFE]
em0: bpf attached
em0: Ethernet address: 00:0e:0c:a0:a6:90
em0: Speed:N/A Duplex:N/A
em1: <Intel(R) PRO/1000 Network Connection, Version - 2.1.7> port
0xec80-0xecbf mem 0xfe9c0000-0xfe9dffff irq 17 at device 4.1 on pci3
em1: Reserved 0x20000 bytes for rid 0x10 type 3 at 0xfe9c0000
em1: Reserved 0x40 bytes for rid 0x20 type 4 at 0xec80
em1: [MPSAFE]
em1: bpf attached
em1: Ethernet address: 00:0e:0c:a0:a6:91
em1: Speed:N/A Duplex:N/A
pcib4: <PCI-PCI bridge> at device 0.2 on pci2
pcib4: secondary bus 4
pcib4: subordinate bus 4
pcib4: I/O decode 0xf000-0xfff
pcib4: memory decode 0xfff00000-0xfffff
pcib4: prefetched decode 0xfff00000-0xfffff
pci4: <PCI bus> on pcib4
pci4: physical bus=4
pcib5: <ACPI PCI-PCI bridge> at device 28.4 on pci0
pcib5: secondary bus 5
pcib5: subordinate bus 5
pcib5: I/O decode 0xd000-0xdfff
pcib5: memory decode 0xfe600000-0xfe7fffff
pcib5: prefetched decode 0xfff00000-0xfffff
pci5: <ACPI PCI bus> on pcib5
pci5: physical bus=5
found-> vendor=0x14e4, dev=0x1659, revid=0x11
bus=5, slot=0, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x0010, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=5
powerspec 2 supports D0 D3 current D0
MSI supports 8 messages, 64 bit
map[10]: type 1, range 64, base fe6f0000, size 16, enabled
pcib5: (null) requested memory range 0xfe6f0000-0xfe6fffff: good
pcib5: matched entry for 5.0.INTA
pcib5: slot 0 INTA hardwired to IRQ 16
bge0: <Broadcom BCM5721 Gigabit Ethernet, ASIC rev. 0x4101> mem
0xfe6f0000-0xfe6fffff irq 16 at device 0.0 on pci5
bge0: Reserved 0x10000 bytes for rid 0x10 type 3 at 0xfe6f0000
miibus0: <MII bus> on bge0
brgphy0: <BCM5750 10/100/1000baseTX PHY> on miibus0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
1000baseTX-FDX, auto
bge0: bpf attached
bge0: Ethernet address: 00:14:22:7b:c7:e5
bge0: [MPSAFE]
pcib6: <ACPI PCI-PCI bridge> at device 28.5 on pci0
pcib6: secondary bus 6
pcib6: subordinate bus 6
pcib6: I/O decode 0xc000-0xcfff
pcib6: memory decode 0xfe400000-0xfe5fffff
pcib6: prefetched decode 0xfff00000-0xfffff
pci6: <ACPI PCI bus> on pcib6
pci6: physical bus=6
found-> vendor=0x14e4, dev=0x1659, revid=0x11
bus=6, slot=0, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x0010, cachelnsz=16 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=3
powerspec 2 supports D0 D3 current D0
MSI supports 8 messages, 64 bit
map[10]: type 1, range 64, base fe4f0000, size 16, enabled
pcib6: (null) requested memory range 0xfe4f0000-0xfe4fffff: good
pcib6: matched entry for 6.0.INTA
pcib6: slot 0 INTA hardwired to IRQ 17
bge1: <Broadcom BCM5721 Gigabit Ethernet, ASIC rev. 0x4101> mem
0xfe4f0000-0xfe4fffff irq 17 at device 0.0 on pci6
bge1: Reserved 0x10000 bytes for rid 0x10 type 3 at 0xfe4f0000
miibus1: <MII bus> on bge1
brgphy1: <BCM5750 10/100/1000baseTX PHY> on miibus1
brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
1000baseTX-FDX, auto
bge1: bpf attached
bge1: Ethernet address: 00:14:22:7b:c7:e6
bge1: [MPSAFE]
uhci0: <UHCI (generic) USB controller> port 0xace0-0xacff irq 20 at
device 29.0 on pci0
uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0xace0
uhci0: [GIANT-LOCKED]
usb0: <UHCI (generic) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <UHCI (generic) USB controller> port 0xacc0-0xacdf irq 21 at
device 29.1 on pci0
uhci1: Reserved 0x20 bytes for rid 0x20 type 4 at 0xacc0
uhci1: [GIANT-LOCKED]
usb1: <UHCI (generic) USB controller> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <UHCI (generic) USB controller> port 0xaca0-0xacbf irq 22 at
device 29.2 on pci0
uhci2: Reserved 0x20 bytes for rid 0x20 type 4 at 0xaca0
uhci2: [GIANT-LOCKED]
usb2: <UHCI (generic) USB controller> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfeb00400-0xfeb007ff irq
20 at device 29.7 on pci0
ehci0: Reserved 0x400 bytes for rid 0x10 type 3 at 0xfeb00400
ehci0: [GIANT-LOCKED]
usb3: EHCI version 1.0
usb3: wrong number of companions (7 != 3)
usb3: companion controllers, 2 ports each: usb0 usb1 usb2
usb3: <EHCI (generic) USB 2.0 controller> on ehci0
usb3: USB revision 2.0
uhub3: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered
pcib7: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pcib7: secondary bus 7
pcib7: subordinate bus 7
pcib7: I/O decode 0xb000-0xbfff
pcib7: memory decode 0xfe200000-0xfe3fffff
pcib7: prefetched decode 0xfd000000-0xfdffffff
pcib7: Subtractively decoded bridge.
pci7: <ACPI PCI bus> on pcib7
pci7: physical bus=7
found-> vendor=0x18ca, dev=0x0020, revid=0x00
bus=7, slot=5, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0023, statreg=0x0230, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 3, range 32, base fd000000, size 24, enabled
pcib7: (null) requested memory range 0xfd000000-0xfdffffff: good
map[14]: type 1, range 32, base fe2c0000, size 18, enabled
pcib7: (null) requested memory range 0xfe2c0000-0xfe2fffff: good
map[18]: type 4, range 32, base 0000bc80, size 7, enabled
pcib7: (null) requested I/O range 0xbc80-0xbcff: in range
pci7: <display, VGA> at device 5.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH7 UDMA100 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfc00-0xfc0f at device 31.1 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xfc00
ata0: <ATA channel 0> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
ata0: stat1=0x00 err=0x04 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=00 stat1=00 devices=0x4<ATAPI_MASTER>
ata0: [MPSAFE]
ata1: <ATA channel 1> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=00 ostat0=ff ostat1=ff
ata1: [MPSAFE]
atapci1: <Intel ICH7 SATA150 controller> port
0xac98-0xac9f,0xac90-0xac93,0xac80-0xac87,0xac78-0xac7b,0xac60-0xac6f
mem 0xfeb00000-0xfeb003ff irq 20 at device 31.2 on pci0
atapci1: Reserved 0x10 bytes for rid 0x20 type 4 at 0xac60
atapci1: [MPSAFE]
atapci1: Reserved 0x400 bytes for rid 0x24 type 3 at 0xfeb00000
atapci1: [MPSAFE]
ata2: <ATA channel 0> on atapci1
ata2: SATA connect status=00000000
ata2: [MPSAFE]
ata3: <ATA channel 1> on atapci1
ata3: SATA connect status=00000000
ata3: [MPSAFE]
ata4: <ATA channel 2> on atapci1
ata4: SATA connect status=00000000
ata4: [MPSAFE]
ata5: <ATA channel 3> on atapci1
ata5: SATA connect status=00000000
ata5: [MPSAFE]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
speaker0: <PC speaker> port 0x61 on acpi0
fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: does not respond
device_attach: fdc0 attach returned 6
sio0: irq maps: 0x4c69 0x4c79 0x4c69 0x4c69
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on
acpi0
sio0: type 16550A
fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: does not respond
device_attach: fdc0 attach returned 6
ex_isa_identify()
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
ahc_isa_probe 0: ioport 0xc00 alloc failed
ahc_isa_probe 10: ioport 0xac00 alloc failed
ahc_isa_probe 11: ioport 0xbc00 alloc failed
ahc_isa_probe 14: ioport 0xec00 alloc failed
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
fdc: fdc0 already exists; skipping it
sio: sio0 already exists; skipping it
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xec000-0xeffff on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
kbd0: atkbd0, generic (0), config:0x0, flags:0x3f0000
atkbd0: [GIANT-LOCKED]
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
ppc0: parallel port not found.
ppc0: <Parallel port> failed to probe at irq 7 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0x4c69 0x4c69 0x4c69 0x4c69
sio1: probe failed test(s): 0 1 2 4 6 7 9
sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
ukbd0: DELL DELL USB Keyboard, rev 1.10/1.04, addr 2, iclass 3/1
kbd: new array size 4
kbd1 at ukbd0
kbd1: ukbd0, generic (0), config:0x0, flags:0x1d0000
Device configuration finished.
procfs registered
lapic: Divisor 2, Frequency 100003758 hz
Timecounter "TSC" frequency 2800121513 Hz quality 800
Timecounters tick every 1.000 msec
crypto: assign driver 0, flags 6
crypto: driver 0 registers alg 1 flags 0 maxoplen 0
crypto: driver 0 registers alg 2 flags 0 maxoplen 0
crypto: driver 0 registers alg 3 flags 0 maxoplen 0
crypto: driver 0 registers alg 4 flags 0 maxoplen 0
crypto: driver 0 registers alg 5 flags 0 maxoplen 0
crypto: driver 0 registers alg 17 flags 0 maxoplen 0
crypto: driver 0 registers alg 6 flags 0 maxoplen 0
crypto: driver 0 registers alg 7 flags 0 maxoplen 0
crypto: driver 0 registers alg 15 flags 0 maxoplen 0
crypto: driver 0 registers alg 8 flags 0 maxoplen 0
crypto: driver 0 registers alg 16 flags 0 maxoplen 0
crypto: driver 0 registers alg 9 flags 0 maxoplen 0
crypto: driver 0 registers alg 10 flags 0 maxoplen 0
crypto: driver 0 registers alg 13 flags 0 maxoplen 0
crypto: driver 0 registers alg 14 flags 0 maxoplen 0
crypto: driver 0 registers alg 11 flags 0 maxoplen 0
crypto: driver 0 registers alg 18 flags 0 maxoplen 0
BRIDGE 031224 loaded
crypto: <crypto device>
Fast IPsec: Initialized Security Association Processing.
pfsync0: bpf attached
lo0: bpf attached
pflog0: bpf attached
md0: Preloaded image </boot/mfsroot> 14483456 bytes at 0xc0ab1208
g_pc98_taste: guessing 17 sectors
g_pc98_taste: guessing 8 heads
g_pc98_taste: guessing 17 sectors
g_pc98_taste: guessing 8 heads
ata0-master: pio=PIO4 wdma=WDMA2 udma=UDMA33 cable=40 wire
acd0: setting PIO4 on Intel ICH7 chip
acd0: setting UDMA33 on Intel ICH7 chip
acd0: <HL-DT-ST GCR-8240N/1.06> CDROM drive at ata0 as master
acd0: read 4125KB/s (4125KB/s), 128KB buffer, UDMA33
acd0: Reads: CDR, CDRW, CDDA stream, packet
acd0: Writes:
acd0: Audio: play, 255 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: CD-ROM 120mm data disc
ATA PseudoRAID loaded
ioapic0: routing intpin 1 (ISA IRQ 1) to cluster 0
ioapic0: routing intpin 4 (ISA IRQ 4) to cluster 0
ioapic0: routing intpin 9 (ISA IRQ 9) to cluster 0
ioapic0: routing intpin 13 (ISA IRQ 13) to cluster 0
ioapic0: routing intpin 14 (ISA IRQ 14) to cluster 0
ioapic0: routing intpin 15 (ISA IRQ 15) to cluster 0
ioapic0: routing intpin 16 (PCI IRQ 16) to cluster 0
ioapic0: routing intpin 17 (PCI IRQ 17) to cluster 0
ioapic0: routing intpin 20 (PCI IRQ 20) to cluster 0
ioapic0: routing intpin 21 (PCI IRQ 21) to cluster 0
ioapic0: routing intpin 22 (PCI IRQ 22) to cluster 0
acd0: FAILURE - READ_BIG ILLEGAL REQUEST asc=0x64 ascq=0x00 error=4<ABORTED>
GEOM_LABEL: Label for provider acd0 is iso9660/FreeSBIE.
g_pc98_taste: guessing 17 sectors
g_pc98_taste: guessing 8 heads
acd0: FAILURE - READ_BIG ILLEGAL REQUEST asc=0x64 ascq=0x00 error=4<ABORTED>
acd0: FAILURE - READ_BIG ILLEGAL REQUEST asc=0x64 ascq=0x00 error=4<ABORTED>
acd0: FAILURE - READ_BIG ILLEGAL REQUEST asc=0x64 ascq=0x00 error=4<ABORTED>
acd0: FAILURE - READ_BIG ILLEGAL REQUEST asc=0x64 ascq=0x00 error=4<ABORTED>
acd0: FAILURE - READ_BIG ILLEGAL REQUEST asc=0x64 ascq=0x00 error=4<ABORTED>
acd0: FAILURE - READ_BIG MEDIUM ERROR asc=0x11 ascq=0x06 error=4<ABORTED>
g_pc98_taste: guessing 17 sectors
g_pc98_taste: guessing 8 heads
acd0: FAILURE - READ_BIG ILLEGAL REQUEST asc=0x64 ascq=0x00 error=4<ABORTED>
acd0: FAILURE - READ_BIG ILLEGAL REQUEST asc=0x64 ascq=0x00 error=4<ABORTED>
acd0: FAILURE - READ_BIG ILLEGAL REQUEST asc=0x64 ascq=0x00 error=4<ABORTED>
acd0: FAILURE - READ_BIG ILLEGAL REQUEST asc=0x64 ascq=0x00 error=4<ABORTED>
acd0: FAILURE - READ_BIG ILLEGAL REQUEST asc=0x64 ascq=0x00 error=4<ABORTED>
acd0: FAILURE - READ_BIG ILLEGAL REQUEST asc=0x64 ascq=0x00 error=4<ABORTED>
acd0: FAILURE - READ_BIG ILLEGAL REQUEST asc=0x64 ascq=0x00 error=4<ABORTED>
acd0: FAILURE - READ_BIG ILLEGAL REQUEST asc=0x64 ascq=0x00 error=4<ABORTED>
acd0: FAILURE - READ_BIG ILLEGAL REQUEST asc=0x64 ascq=0x00 error=4<ABORTED>
acd0: FAILURE - READ_BIG ILLEGAL REQUEST asc=0x64 ascq=0x00 error=4<ABORTED>
Trying to mount root from ufs:/dev/md0
start_init: trying /sbin/init
___
___/ f \\
/ p \\___/ Sense
\\___/ \\
\\___/
Welcome to pfSense 0.90 on the 'cdrom' platform...
Running CDROM routines...
Mounting /FreeSBIE... (ignore error messages)
Mounting /usr...
WARNING: opening backing store: /FreeSBIE/uzip/usr.uzip readonly
md1.uzip: 1359 x 65536 blocks
g_pc98_taste: guessing 17 sectors
g_pc98_taste: guessing 8 heads
Memory devices:
g_pc98_taste: guessing 17 sectors
g_pc98_taste: guessing 8 heads
g_pc98_taste: guessing 17 sectors
g_pc98_taste: guessing 8 heads
/tmp
Starting pfi...
Looking for pfi.conf on /dev/acd0c...
Copying /FreeSBIE/cf/conf/* /cf/conf/
Copying config.xml to /conf.default/conf/
No swap on cdrom
Removing /etc/rc.conf...
Starting USB...
kbd1
ukbd0, type:generic (0)
done.
Starting device manager (devd)...
done.
Loading configuration...
done.
LAN sis0 interface mismatch.
-- Running interface assignment option.
Valid interfaces are:
em0 00:0e:0c:a0:a6:90
em1 00:0e:0c:a0:a6:91
bge0 00:14:22:7b:c7:e5
bge1 00:14:22:7b:c7:e6
Do you want to set up VLANs first?
If you are not going to use VLANs, or only for optional interfaces, you
should say no here and use the webGUI to configure VLANs later, if required.
Do you want to set up VLANs now [y|n]?
Enter the parent interface name for the new VLAN (or nothing if finished):
Enter the VLAN tag (1-4094):
Enter the parent interface name for the new VLAN (or nothing if finished):
VLAN interfaces:
vlan0 VLAN tag 40, interface em0
*NOTE* pfSense requires *ATLEAST* 2 assigned interfaces to function.
If you do not have two interfaces turn off the machine until
you do.
If you do not know the names of your interfaces, you may choose to use
auto-detection... In that case, disconnect all interfaces now before
hitting a. The system will then prompt you to plug in each nic to
autodetect.
Enter the LAN interface name or 'a' for auto-detection:
Enter the WAN interface name or 'a' for auto-detection:
Enter the Optional 1 interface name or 'a' for auto-detection
(or nothing if finished):
The interfaces will be assigned as follows:
LAN -> vlan0
WAN -> em1
Do you want to proceed [y|n]?
Updating configuration...
done.
Cleaning backup cache...
done.
Setting up extended sysctls...
done.
Syncing user passwords...
done.
Setting timezone...
done.
Starting syslog...
done.
vlan0: bpf attached
Configuring LAN interface...
bge0: link state changed to UP
bge1: link state changed to DOWN
done.
Configuring WAN interface...
em0: Link is up 1000 Mbps Full Duplex
em0: link state changed to UP
vlan0: link state changed to UP
em1: Link is up 1000 Mbps Full Duplex
em1: link state changed to UP
em1: Link is up 1000 Mbps Full Duplex
done.
Configuring OPT interfaces...
done.
pflog0: promiscuous mode enabled
Configuring CARP interfaces...
done.
Configuring firewall...
aliases
rules
filtering
done.
Starting webConfigurator...
done
Starting DNS forwarder...
done.
Starting DHCP service...
done.
Warning: Invalid argument supplied for foreach() in
/etc/inc/services.inc on line 308
Starting NTP client...
done.
Starting FTP helpers...
done.
Starting Secure Shell Services...
Generating Keys:
Generating public/private rsa1 key pair.
Your identification has been saved in /etc/ssh/ssh_host_key.
Your public key has been saved in /etc/ssh/ssh_host_key.pub.
The key fingerprint is:
c0:39:10:fd:37:b6:a2:bd:0d:81:fc:2b:24:6f:2c:76 [EMAIL PROTECTED]
Generating public/private rsa key pair.
Your identification has been saved in /etc/ssh/ssh_host_rsa_key.
Your public key has been saved in /etc/ssh/ssh_host_rsa_key.pub.
The key fingerprint is:
1c:42:e8:9b:ae:6d:6d:17:cc:1a:70:80:81:c8:66:70 [EMAIL PROTECTED]
Generating public/private dsa key pair.
Your identification has been saved in /etc/ssh/ssh_host_dsa_key.
Your public key has been saved in /etc/ssh/ssh_host_dsa_key.pub.
The key fingerprint is:
40:53:92:dc:77:90:d6:8c:7a:9d:4c:4b:7c:4e:65:15 [EMAIL PROTECTED]
Starting SSH...
done.
Starting CRON...
done.
Bootup complete
FreeBSD/i386 (pfSense.local) (console)
login:
Scott Ullrich wrote:
From the loader prompt (Press ENTER to boot yadda yadda) try to boot
-v and then post dmesg -a
Scott
On 11/1/05, Lynn A. Roth <[EMAIL PROTECTED]> wrote:
I get the same thing with FreeBSD 6.0 RC1. It boots to the installer
and then when attempting to install, it says it can't find a disk. The
controller is found as a SATA. Here is the relevant portion of dmesg
(this is from pfSense, but the RC1 looked the same)
atapci0: <Intel ICH7 UDMA100 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfc00-0xfc0f at device 31.1 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
atapci1: <Intel ICH7 SATA150 controller> port
0xac98-0xac9f,0xac90-0xac93,0xac80-0xac87,0xac78-0xac7b,0xac60-0xac6f
mem 0xfeb00000-0xfeb003ff irq 20 at device 31.2 on pci0
ata2: <ATA channel 0> on atapci1
ata3: <ATA channel 1> on atapci1
ata4: <ATA channel 2> on atapci1
ata5: <ATA channel 3> on atapci1
Lynn
Scott Ullrich wrote:
It appears that FreeBSD is not seeing this drive as attached for some
reason. Can you try a FreeBSD RC disk?
On 11/1/05, Lynn A. Roth <[EMAIL PROTECTED]> wrote:
Some more info:
when I run atacontrol info, it appears that the disk is not attached. I
have booted to Linux and Windows installer and they both see the disk. I
believe that the SATA drive should be on ATA channel 2. (According to th
e boot messages, which show the ICH7 SATA Controller being detected with
4 channels, 2-5)
# atacontrol list
ATA channel 0:
Master: acd0 <HL-DT-ST GCR-8240N/1.06> ATA/ATAPI revision 4
Slave: no device present
ATA channel 1:
Master: no device present
Slave: no device present
ATA channel 2:
Master: no device present
Slave: no device present
ATA channel 3:
Master: no device present
Slave: no device present
ATA channel 4:
Master: no device present
Slave: no device present
ATA channel 5:
Master: no device present
Slave: no device present
Scott Ullrich wrote:
Please send the contents of /tmp/ after you receive the error message.
CTRL-C a number of times to break back to the shell and then SCP
then files somewhere.
Scott
On 11/1/05, Lynn A. Roth <[EMAIL PROTECTED]> wrote:
I should also note that it has a single SATA drive on the first SATA
connection. I get the same issue with both of the two identical
systems.
Lynn
Scott Ullrich wrote:
What version?
On 11/1/05, Lynn A. Roth <[EMAIL PROTECTED]> wrote:
I'm having trouble installing pfSense to my new Dell PE 850.
The installer doesn't find a disk. If I do an lsdev before booting,
I
see the disk and partitions. The system has a ICH7 chipset, which
appears to be problematic at this point in time. Does anyone have
any
idea how I could get this installed? Is there a way to easily
update
the kernel in the installer? Would that even help?
Thanks.
Lynn A. Roth
Network Administrator
Interactive Financial Solutions, Inc.
---------------------------------------------------------------------
To unsubscribe, e-mail: [EMAIL PROTECTED]
For additional commands, e-mail: [EMAIL PROTECTED]
---------------------------------------------------------------------
To unsubscribe, e-mail: [EMAIL PROTECTED]
For additional commands, e-mail: [EMAIL PROTECTED]