Where is problem I have two procesors instald and it seems to run just
on one. Kernel 2.1.132
klogd 1.3-0, log source = /proc/kmsg started.
<4>Linux version 2.1.132 (root@office) (gcc version 2.7.2.1) #2 SMP Wed Dec 23
15:14:48 CET 1998
<4>Intel MultiProcessor Specification v1.4
<4> Virtual Wire compatibility mode.
<4>OEM ID: INTEL Product ID: PR440FX APIC at: 0xFEC08000
<4>Processor #0 Pentium(tm) Pro APIC version 17
<4>I/O APIC #13 Version 17 at 0xFEC00000.
<4>Processors: 1
<4>mapped APIC to ffffe000 (fec08000)
<4>mapped IOAPIC to ffffd000 (fec00000)
<4>Detected 198670369 Hz processor.
<4>Console: colour VGA+ 80x25
<4>Calibrating delay loop... 198.25 BogoMIPS
<4>Memory: 257252k/262144k available (1004k kernel code, 412k reserved, 3436k data,
40k init)
<5>VFS: Diskquotas version dquot_6.4.0 initialized
<6>Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
<6>Checking 'hlt' instruction... OK.
<4>POSIX conformance testing by UNIFIX
<4>mtrr: v1.26 (19981001) Richard Gooch ([EMAIL PROTECTED])
<4>CPU0: Intel Pentium Pro stepping 09
<4>calibrating APIC timer ...
<4>..... CPU clock speed is 198.6716 MHz.
<4>..... APIC bus clock speed is 66.2236 MHz.
<3>Error: only one processor found.
<4>enabling symmetric IO mode... ...done.
<4>ENABLING IO-APIC IRQs
<4>init IO_APIC IRQs
<4> IO-APIC pin 0, 2, 9, 11, 13, 19, 20, 21, 22, 23 not connected.
<4>...trying to set up timer as ExtINT... .. (found pin 0) ... works.
<4>number of MP IRQ sources: 15.
<4>number of IO-APIC registers: 24.
<4>testing the IO APIC.......................
<4>.... register #00: 0D000000
<4>....... : physical APIC id: 0D
<4>.... register #01: 00170011
<4>....... : max redirection entries: 0017
<4>....... : IO APIC version: 0011
<4>.... register #02: 0F000000
<4>....... : arbitration: 0F
<4>.... IRQ redirection table:
<4> NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
<4> 00 001 01 0 0 0 0 0 1 7 00
<4> 01 000 00 0 0 0 0 0 1 1 59
<4> 02 000 00 1 0 0 0 0 0 0 00
<4> 03 000 00 0 0 0 0 0 1 1 61
<4> 04 000 00 0 0 0 0 0 1 1 69
<4> 05 000 00 0 0 0 0 0 1 1 71
<4> 06 000 00 0 0 0 0 0 1 1 79
<4> 07 000 00 0 0 0 0 0 1 1 81
<4> 08 000 00 0 0 0 0 0 1 1 89
<4> 09 000 00 1 0 0 0 0 0 0 00
<4> 0a 000 00 0 0 0 0 0 1 1 91
<4> 0b 000 00 1 0 0 0 0 0 0 00
<4> 0c 000 00 0 0 0 0 0 1 1 99
<4> 0d 000 00 1 0 0 0 0 0 0 00
<4> 0e 000 00 0 0 0 0 0 1 1 A1
<4> 0f 000 00 0 0 0 0 0 1 1 A9
<4> 10 0FF 0F 1 1 0 1 0 1 1 B1
<4> 11 0FF 0F 1 1 0 1 0 1 1 B9
<4> 12 0FF 0F 1 1 0 1 0 1 1 C1
<4> 13 000 00 1 0 0 0 0 0 0 00
<4> 14 000 00 1 0 0 0 0 0 0 00
<4> 15 000 00 1 0 0 0 0 0 0 00
<4> 16 000 00 1 0 0 0 0 0 0 00
<4> 17 000 00 1 0 0 0 0 0 0 00
<7>IRQ to pin mappings:
<7>IRQ1 -> 1
<7>IRQ3 -> 3
<7>IRQ4 -> 4
<7>IRQ5 -> 5
<7>IRQ6 -> 6
<7>IRQ7 -> 7
<7>IRQ8 -> 8
<7>IRQ10 -> 10
<7>IRQ12 -> 12
<7>IRQ14 -> 14
<7>IRQ15 -> 15
<7>IRQ16 -> 16
<7>IRQ17 -> 17
<7>IRQ18 -> 18
<4>.................................... done.
<4>PCI: PCI BIOS revision 2.10 entry at 0xfda11
<4>PCI: Using configuration type 1
<4>PCI: Probing PCI hardware
<4>PCI->APIC IRQ transform: (B0,I6,P0) -> 18
<4>PCI->APIC IRQ transform: (B0,I9,P0) -> 17
<4>PCI->APIC IRQ transform: (B0,I11,P0) -> 16
<4>PCI: 00:00 [8086/1237]: Passive release enable (00)
<6>Swansea University Computer Society NET3.039 for Linux 2.1
<6>NET3: Unix domain sockets 0.16 for Linux NET3.038.
<6>Swansea University Computer Society TCP/IP for NET3.037
<6>IP Protocols: ICMP, UDP, TCP
<4>Starting kswapd v 1.5
<6>Serial driver version 4.27 with no serial options enabled
<6>ttyS00 at 0x03f8 (irq = 4) is a 16550A
<6>ttyS01 at 0x02f8 (irq = 3) is a 16550A
<4>pty: 256 Unix98 ptys configured
<6>Real Time Clock Driver v1.09
<6>Floppy drive(s): fd0 is 1.44M
<6>FDC 0 is a National Semiconductor PC87306
Kernel logging (proc) stopped.
Kernel log daemon terminating.
-
To get out of this list, please send email to [EMAIL PROTECTED] with
this text in its body: unsubscribe suse-linux-e
Check out the SuSE-FAQ at http://www.suse.com/Support/Doku/FAQ/ and the
archiv at http://www.suse.com/Mailinglists/suse-linux-e/index.html
