I'm using the SeaBIOS provided with the machine, and have no news on a
upcoming newer release. So far it works for me flawlessly with the
limits stated by the manufacturer.
System startup messages:
SeaBIOS (version rel-1.8.0-143-g174faf8-dirty-20150928_122234-wim-ws)
XHCI init on dev 00:10.0: regs @ 0xfeb22000, 4 ports, 32 slots, 32 byte
contexts
XHCI extcap 0x1 @ feb22500
XHCI protocol USB 3.00, 2 ports (offset 1), def 0
XHCI protocol USB 2.00, 2 ports (offset 3), def 10
XHCI extcap 0xa @ feb22540
Found 2 serial ports
ATA controller 1 at 4010/4020/0 (irq 0 dev 88)
EHCI init on dev 00:13.0 (regs=0xfeb25420)
ATA controller 2 at 4018/4024/0 (irq 0 dev 88)
Searching bootorder for: /pci@i0cf8/*@14,7
Searching bootorder for: /rom@img/memtest
Searching bootorder for: /rom@img/setup
ata0-0: SATA SSD ATA-10 Hard-Disk (15272 MiBytes)
Searching bootorder for: /pci@i0cf8/*@11/drive@0/disk@0
XHCI port #3: 0x00200e03, powered, enabled, pls 0, speed 3 [High]
Searching bootorder for: /pci@i0cf8/usb@10/storage@3/*@0/*@0,0
Searching bootorder for: /pci@i0cf8/usb@10/usb-*@3
USB MSC vendor='SanDisk' product='Cruzer Fit' rev='1.26' type=0 removable=0
USB MSC blksize=512 sectors=31266816
Initialized USB HUB (0 ports used)
All threads complete.
Scan for option roms
PCengines Press F10 key now for boot menu:
Searching bootorder for: HALT
drive 0x000f2e30: PCHS=0/0/0 translation=lba LCHS=1024/255/63 s=31266816
drive 0x000f2e60: PCHS=16383/16/63 translation=lba LCHS=1024/255/63
s=31277232
Space available for UMB: c1000-ef000, f0000-f2e30
On 14/11/15 19:22, Mathias Schmocker wrote:
Le 14.11.15 17:02, Chris Cappuccio a écrit :
> Mathias Schmocker [s...@smat.ch] wrote:
>>
>> First tests with a bootable OpenBSD amd64 5.8-current USB stick and
>> installation on the 16GB mSata internal storage.
>> After reboot, BIOS could find mSata to boot on, but defaulted to
the memtest
>> boot payload
>>
>
> This is a setting you can change, although the default boot order
would put memtest last.
Not for me:
1. USB MSC Drive SanDisk Ultra Fit 1.00
2. Payload [memtest]
3. Payload [setup]
I have now successfully installed and booted on a small 16GB SanDisk
USB key, root on sd1a (but I had a hard lockup once, with >
xhci_wait_for_command: Command ring still running ...)
But pressing F10 and 3 to access setup and placing mSata in front of
all the other does NOT work (even if sd0a has a bootable bsd.rd, /boot
and the proper /etc/boot.conf, and is accessible once OpenBSD runs out
of the USB key ...)
Which SeaBIOS, BUILD version, and option rom does your APU2 display
when booting up ?
> I've had no problems with apu2 detecting msata so far..
>
>> Unable to abort memtest by pressing (esc) on the serial console, or
(c) for
>> configure.
>>
>
> You have to escape to the prompt before memtest starts.
>
>
