It looks like there's still a problem with the trimmers. R17 and R22
are shown as part # 3266P-1-502LF and the photo shows the proper type of
trimmer. The data sheet and the catalog page show that 3266P has the
adjustment parallel to the board rather than vertical. Mouser just used
the same picture for all styles of the 3266 line. There are others that
are in stock, but they're larger and I don't know if there's room for
them on the board.
Ed
Bob Bownes wrote:
Changed it to a different part that is available. Difference is RHoS
compliance method.
Changed the backordered 2n3906 as well. Shaved $0.02 off the total cost!
Bob
On Fri, Jul 2, 2010 at 3:17 PM, Bob Camp <li...@rtty.us> wrote:
Hi
It looks like it may be a while before the trim pots come in (12 weeks...).
The 3266X (side adjust rather than top adjust) is in stock. I'm not sure if
the layout is "side adjust" friendly or not.
Bob
-----Original Message-----
From: time-nuts-boun...@febo.com [mailto:time-nuts-boun...@febo.com] On
Behalf Of Bob Bownes
Sent: Friday, July 02, 2010 2:54 PM
To: Discussion of precise time and frequency measurement
Subject: Re: [time-nuts] Pic programing for the PICTIC II
Folks,
I put together a mouser 'project' with all of the parts. This means
you can just go to the mouser site and order all the parts for the
project. No need for anyone to do a group buy of parts, re-pack and
re-distribute them. Here's how to get to it:
To access the project, click on the url listed below or copy and paste
it into your web browser:
http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=c7ada9ced0
Or you can access the project by going to http://www.mouser.com/ and
click on the EZ Buy option on the top navigation bar. You can also
click on this link or copy and paste it into your browser:
http://www.mouser.com/Tools/Tools.aspx. Then enter the following
access number listed below into the Project Access ID function.
c7ada9ced0
Total cost w/o shipping is $30.30.
On Fri, Jul 2, 2010 at 1:23 PM, Peter Vince <pvi...@theiet.org> wrote:
Apologies for the previous incomplete message - somehow my laptop
trackpad jumped the cursor over the send button :-(
Better ?
How many16f688s are we talking here?
My thinking is less than 10 as only two people have asked.
Don't know how many have not asked.
I would also like a pre-programmed PIC please, if someone can arrange
that. Or ideally, a complete kit of parts, but as the previous
correspondent has written, I appreciate that is a lot of work.
Thanks,
Peter Vince (London, England)
_______________________________________________
time-nuts mailing list -- time-nuts@febo.com
To unsubscribe, go to
https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.
_______________________________________________
time-nuts mailing list -- time-nuts@febo.com
To unsubscribe, go to
https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.
_______________________________________________
time-nuts mailing list -- time-nuts@febo.com
To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.
_______________________________________________
time-nuts mailing list -- time-nuts@febo.com
To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.
_______________________________________________
time-nuts mailing list -- time-nuts@febo.com
To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.
