I am familiar with that problem. I usually turn on my GPSDO system for a week or two at a time when I am in the shop periodically working on a project that I need precision references for. Therefore, I will turn on the computer first, then turn on the TBolt and Z3816A. If I ever get to the point of making up a 'reference' TBolt System' with self contained power supply, heatsink/fan, etc., I would want to leave it on indefinitely and turn on the computer intermittently. That is when I will need to know how to fix the 'mouse' issue. I remember reading a post several months ago about how to go into some file and remove reference to serial mice so that it will not even look for them.
Joe -----Original Message----- From: time-nuts-boun...@febo.com [mailto:time-nuts-boun...@febo.com]On Behalf Of Bob Camp Sent: Wednesday, January 19, 2011 11:38 AM To: 'Discussion of precise time and frequency measurement' Subject: Re: [time-nuts] LH v3.0 Beta and Z3816A Question Hi If you haven't re-booted yet, you may not have seen windows detect your TBolt and 3816 as mice yet. It's a simple thing to fix (disable it in device manager), but a common "next problem". Bob -----Original Message----- From: time-nuts-boun...@febo.com [mailto:time-nuts-boun...@febo.com] On Behalf Of J. L. Trantham Sent: Wednesday, January 19, 2011 12:07 AM To: 'Discussion of precise time and frequency measurement' Subject: Re: [time-nuts] LH v3.0 Beta and Z3816A Question I am only using LH with the TBolt. I also run a Z3816A simultaneously to cross check frequencies to make sure I am not using a 'dead' reference. I monitor both on the same computer that has two serial ports and runs Win2KPro. I had previously used TBoltMon but decided to give LH a try. Quite the amazing display. It is going to take me weeks to get a handle on all that it can do. The problem I had was downloading and installing the program while the TBolt was operating and connected to COM 2. The only way I could get the program to respond was to move the TBolt to COM 1. After that, everything worked. I have not tried telling LH to switch to COM 2 then moving the TBolt back to COM 2 to see if that would work. My Symmetricom SatStat program is doing fine with the Z3816A on COM 2 so no need as best I can tell. The confusion is probably that I asked two unrelated questions in the same posting. Joe -----Original Message----- From: time-nuts-boun...@febo.com [mailto:time-nuts-boun...@febo.com] On Behalf Of paul swed Sent: Tuesday, January 18, 2011 4:18 PM To: Discussion of precise time and frequency measurement Subject: Re: [time-nuts] LH v3.0 Beta and Z3816A Question A quick question I thought lady heather was a Tbolt program only. Does it work with other GPSDP like the hp 3801 etc??? Thanks On Tue, Jan 18, 2011 at 9:20 AM, J. L. Trantham <jlt...@att.net> wrote: > The Z3816A responded to the command nicely. I was also able to use > the > command: > *tst? > to reboot the receiver without having to turn off the Z3816A. This was > using Symmetricom SatStat v5.0. I have not tried with HP SatStat v4.2. > > Initially, the time was off by what appeared to be the leap second > value with a TFOM of 6. Now it is back to a TFOM of 3 and the time > appears correct. > > Thanks, > > Joe > > -----Original Message----- > From: time-nuts-boun...@febo.com [mailto:time-nuts-boun...@febo.com]On > Behalf Of J. L. Trantham > Sent: Tuesday, January 18, 2011 6:36 AM > To: 'Discussion of precise time and frequency measurement' > Subject: Re: [time-nuts] LH v3.0 Beta and Z3816A Question > > > Michael, > > Thanks for the hint. I've looked at that site a thousand times but > never found that hint until now. I'll give it a try. > > Thanks again. > > Joe > > -----Original Message----- > From: time-nuts-boun...@febo.com [mailto:time-nuts-boun...@febo.com] > On Behalf Of cook michael > Sent: Tuesday, January 18, 2011 2:20 AM > To: time-nuts@febo.com > Subject: Re: [time-nuts] LH v3.0 Beta and Z3816A Question > > > Le 18/01/2011 05:07, J. L. Trantham a écrit : > > An unrelated question. My Z3816A reports GPS time. I have looked > > but have not found a command to make it switch to UTC. Does such a > > command exist? If so, what is it? > > > The command to do the same on the Z3801A might work with this box > aswell. > > Using info from K8CU; > http://www.realhamradio.com/GPS_Frequency_Standard.htm > > Issue the command: > > :diag:gps:utc? > > If it returns 0 you are in GPS mode; if 1 you are in UTC > > Use the command: > > :diag:gps:utc 1 > > followed by > > :syst:pon > > to set it to UTC mode. Some units have to be powered off to actually > reset to UTC depending on software version. > > > > > _______________________________________________ > time-nuts mailing list -- time-nuts@febo.com > To unsubscribe, go to > https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > and follow the instructions there. > > > _______________________________________________ > time-nuts mailing list -- time-nuts@febo.com > To unsubscribe, go to > https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > and follow the instructions there. > No virus found in this incoming message. > Checked by AVG - www.avg.com > Version: 9.0.872 / Virus Database: 271.1.1/3386 - Release Date: > 01/17/11 01:34:00 > > > _______________________________________________ > time-nuts mailing list -- time-nuts@febo.com > To unsubscribe, go to > https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > and follow the instructions there. > _______________________________________________ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there. _______________________________________________ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there. _______________________________________________ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there. ----- No virus found in this message. Checked by AVG - www.avg.com Version: 10.0.1191 / Virus Database: 1435/3390 - Release Date: 01/19/11 _______________________________________________ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.