On Thu, Dec 5, 2013 at 11:01 PM, Dennis Gilmore <den...@ausil.us> wrote: > El Thu, 5 Dec 2013 21:47:43 -0600 > Robert Nelson <robertcnel...@gmail.com> escribió: >> On Thu, Dec 5, 2013 at 8:18 PM, Dennis Gilmore <den...@ausil.us> >> wrote: >> > Signed-off-by: Dennis Gilmore <den...@ausil.us> >> > --- >> > include/configs/wandboard.h | 40 >> > +++++++++++++++++++++++++++++++++++----- 1 file changed, 35 >> > insertions(+), 5 deletions(-) >> > >> > diff --git a/include/configs/wandboard.h >> > b/include/configs/wandboard.h index e9c7e64..02d8968 100644 >> > --- a/include/configs/wandboard.h >> > +++ b/include/configs/wandboard.h >> > @@ -40,6 +40,9 @@ >> > #define CONFIG_CONS_INDEX 1 >> > #define CONFIG_BAUDRATE 115200 >> > >> > +/* enable generic distro config */ >> > +#define DISTRO_DEFAULTS 1 >> > + >> > /* Command definition */ >> > #include <config_cmd_default.h> >> > >> > @@ -48,7 +51,6 @@ >> > #define CONFIG_CMD_BMODE >> > #define CONFIG_CMD_SETEXPR >> > >> > -#define CONFIG_BOOTDELAY 5 >> > >> > #define CONFIG_SYS_MEMTEST_START 0x10000000 >> > #define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + >> > 500 * SZ_1M) @@ -65,6 +67,9 @@ >> > #define CONFIG_CMD_MMC >> > #define CONFIG_GENERIC_MMC >> > #define CONFIG_BOUNCE_BUFFER >> > + >> > +#define CONFIG_BOOTDELAY 5 >> > + >> > #define CONFIG_CMD_EXT2 >> > #define CONFIG_CMD_FAT >> > #define CONFIG_DOS_PARTITION >> > @@ -74,6 +79,11 @@ >> > #define CONFIG_CMD_DHCP >> > #define CONFIG_CMD_MII >> > #define CONFIG_CMD_NET >> > + >> > +#define CONFIG_OF_LIBFDT >> > +#define CONFIG_CMD_BOOTZ >> > + >> > +/* Ethernet Configuration */ >> > #define CONFIG_FEC_MXC >> > #define CONFIG_MII >> > #define IMX_FEC_BASE ENET_BASE_ADDR >> > @@ -113,8 +123,30 @@ >> > "fdt_high=0xffffffff\0" \ >> > "initrd_high=0xffffffff\0" \ >> > "fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \ >> > - "fdt_addr=0x11000000\0" \ >> > + "fdt_addr=0x11100000\0" \ >> > + "fdt_addr_r=0x11200000\0" \ >> > + "pxefile_addr_r=0x11300000\0" \ >> > + "scr_addr_r=0x11400000\0" \ >> > + "kernel_addr_r=0x11500000\0" \ >> > + "ramdisk_addr_r=0x13500000\0" \ >> > "boot_fdt=try\0" \ >> > + "bootcmd_setup=mmc rescan\0" \ >> > + "bootcmd_pxe=setenv bootfile \"\" ;dhcp; tftp >> > ${fdt_addr} /dtb/${fdt_file}; pxe get; pxe boot\0" \ >> > + "bootcmd_disk_scr=ext2load ${boot_ifc} ${bootdevice} >> > ${scr_addr_r} boot.scr && >> >> Why all the non-generic "ext2load"'s? use just "load", then it'll work >> with both fat, ext2/3/4 & btrfs... >> >> Regards, > > the pxe code requires you specify the filesystem for the sysboot > command, and as /boot needs to be ext ive kept it consistent. Ive also > not narrowed down the option to enable load to work, in my testing it > did not work.
Ah, i see the issue, "#define CONFIG_CMD_FS_GENERIC" isn't defined yet for the wandboard in mainline u-boot, as you don't set it either in your patch, so of course a generic "load" won't work.. So if you add: #define CONFIG_CMD_EXT4 #define CONFIG_CMD_FS_GENERIC after: #define CONFIG_CMD_EXT2 in your patch you can drop all the ext2load non-sense for generic loads. I've been shipping ubuntu/debian images with '#define CONFIG_CMD_FS_GENERIC' and 'load' for the wand since v2013.07 with no issues.. Regards, -- Robert Nelson http://www.rcn-ee.com/ _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot