El Thu, 5 Dec 2013 23:01:13 -0600 Dennis Gilmore <den...@ausil.us> escribió: > El Thu, 5 Dec 2013 21:47:43 -0600 > Robert Nelson <robertcnel...@gmail.com> escribió: > > On Thu, Dec 5, 2013 at 8:18 PM, Dennis Gilmore <den...@ausil.us> > > wrote: > > > Signed-off-by: Dennis Gilmore <den...@ausil.us> > > > --- > > > include/configs/wandboard.h | 40 > > > +++++++++++++++++++++++++++++++++++----- 1 file changed, 35 > > > insertions(+), 5 deletions(-) > > > > > > diff --git a/include/configs/wandboard.h > > > b/include/configs/wandboard.h index e9c7e64..02d8968 100644 > > > --- a/include/configs/wandboard.h > > > +++ b/include/configs/wandboard.h > > > @@ -40,6 +40,9 @@ > > > #define CONFIG_CONS_INDEX 1 > > > #define CONFIG_BAUDRATE 115200 > > > > > > +/* enable generic distro config */ > > > +#define DISTRO_DEFAULTS 1 > > > + > > > /* Command definition */ > > > #include <config_cmd_default.h> > > > > > > @@ -48,7 +51,6 @@ > > > #define CONFIG_CMD_BMODE > > > #define CONFIG_CMD_SETEXPR > > > > > > -#define CONFIG_BOOTDELAY 5 > > > > > > #define CONFIG_SYS_MEMTEST_START 0x10000000 > > > #define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START > > > + 500 * SZ_1M) @@ -65,6 +67,9 @@ > > > #define CONFIG_CMD_MMC > > > #define CONFIG_GENERIC_MMC > > > #define CONFIG_BOUNCE_BUFFER > > > + > > > +#define CONFIG_BOOTDELAY 5 > > > + > > > #define CONFIG_CMD_EXT2 > > > #define CONFIG_CMD_FAT > > > #define CONFIG_DOS_PARTITION > > > @@ -74,6 +79,11 @@ > > > #define CONFIG_CMD_DHCP > > > #define CONFIG_CMD_MII > > > #define CONFIG_CMD_NET > > > + > > > +#define CONFIG_OF_LIBFDT > > > +#define CONFIG_CMD_BOOTZ > > > + > > > +/* Ethernet Configuration */ > > > #define CONFIG_FEC_MXC > > > #define CONFIG_MII > > > #define IMX_FEC_BASE ENET_BASE_ADDR > > > @@ -113,8 +123,30 @@ > > > "fdt_high=0xffffffff\0" \ > > > "initrd_high=0xffffffff\0" \ > > > "fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \ > > > - "fdt_addr=0x11000000\0" \ > > > + "fdt_addr=0x11100000\0" \ > > > + "fdt_addr_r=0x11200000\0" \ > > > + "pxefile_addr_r=0x11300000\0" \ > > > + "scr_addr_r=0x11400000\0" \ > > > + "kernel_addr_r=0x11500000\0" \ > > > + "ramdisk_addr_r=0x13500000\0" \ > > > "boot_fdt=try\0" \ > > > + "bootcmd_setup=mmc rescan\0" \ > > > + "bootcmd_pxe=setenv bootfile \"\" ;dhcp; tftp > > > ${fdt_addr} /dtb/${fdt_file}; pxe get; pxe boot\0" \ > > > + "bootcmd_disk_scr=ext2load ${boot_ifc} ${bootdevice} > > > ${scr_addr_r} boot.scr && > > > > Why all the non-generic "ext2load"'s? use just "load", then it'll > > work with both fat, ext2/3/4 & btrfs... > > > > Regards, > > the pxe code requires you specify the filesystem for the sysboot > command, and as /boot needs to be ext ive kept it consistent. Ive also > not narrowed down the option to enable load to work, in my testing it > did not work. having said that I just found CONFIG_CMD_FS_GENERIC which is not set, though cmd_pxe.c will need some patching to not require specifying a filesystem
Dennis Dennis _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot