On 07/21/2017 12:04 PM, Bin Meng wrote: > Hi Marek, > > On Fri, Jul 21, 2017 at 4:56 PM, Marek Vasut <ma...@denx.de> wrote: >> On 07/21/2017 10:54 AM, Bin Meng wrote: >>> Hi Marek, >>> >>> On Thu, Jul 20, 2017 at 8:20 PM, Marek Vasut <ma...@denx.de> wrote: >>>> On 07/20/2017 02:16 PM, Bin Meng wrote: >>>>> Hi Marek, >>>>> >>>>> On Thu, Jul 20, 2017 at 7:12 AM, Bin Meng <bmeng...@gmail.com> wrote: >>>>>> This series is the final series of the xHCI driver update. >>>>>> >>>>>> This adds the missing interrupt transfer support to xHCI driver, so >>>>>> that devices like USB keyboard that uses interrupt transfer when >>>>>> CONFIG_SYS_USB_EVENT_POLL is defined can work. >>>>>> >>>>>> This also adds full speed device support. Unlike low/high/super speed >>>>>> devices, full speed device may report its endpoint 0 max packet size >>>>>> as 8/16/32/64. xHCI driver guesses 64 for the first attempt to get the >>>>>> initial 8 bytes device descriptor, and later adjusts the context for >>>>>> endpoint 0. >>>>>> >>>>>> This series also made several updates to xHCI driver to conform with >>>>>> the spec. >>>>>> >>>>>> Previous two series: >>>>>> [1]: usb: xhci: Fix USB xHCI support on Intel platform >>>>>> https://lists.denx.de/pipermail/u-boot/2017-June/296166.html >>>>>> [2]: usb: hub: Support USB 3.0 hubs >>>>>> https://lists.denx.de/pipermail/u-boot/2017-June/296284.html >>>>>> >>>>>> This series is available at u-boot-x86/xhci-working3 for testing. >>>>>> >>>>>> Changes in v3: >>>>>> - rebase on u-boot-usb/master >>>>>> - add changes to poplar.h >>>>>> >>>>>> Bin Meng (13): >>>>>> usb: xhci: Add interrupt transfer support >>>>>> usb: configs: Clean up CONFIG_SYS_USB_EVENT_POLL_(xxx) in board >>>>>> configs >>>>>> usb: kbd: kconfig: Set a default polling mechanism for USB keyboard >>>>>> usb: Only get 64 bytes device descriptor for full speed devices >>>>>> usb: Read device descriptor after device is addressed for xHCI >>>>>> usb: xhci: Fix max packet size for full speed device endpoint 0 >>>>>> usb: hub: Clear port reset before usb_hub_port_connect_change() >>>>>> usb: hub: Clear BH reset status change for a 3.0 hub >>>>>> usb: Handle audio extension endpoint descriptor in usb_parse_config() >>>>>> usb: xhci: Honor endpoint's interval >>>>>> usb: xhci: Program max burst size for endpoint >>>>>> usb: xhci: Set 'Error Count' to 0 for isoch endpoints >>>>>> usb: xhci: Set 'Average TRB Length' to 8 for control endpoints >>>>>> >>>>> >>>>> This is the last xHCI series I have. Can you please take a look and apply? >>>> >>>> I'd like to see some RB/TB from Stefan Roese first if possible. >>>> >>> >>> OK, if that's the case, can you send a pull request to Tom to get usb >>> in? So that I can apply Stefan's x86 patch series on top of this. (I >>> cannot send PR for x86 before the usb changes) >> >> I actually cannot because the USB is currently broken, sorry, I'm >> waiting for a fix before I do that. >> >> Stefan, can you look at this series please? > > What "broken" issues are you seeing?
I think Layerscape stopped building. Look at email with this subject "Compile failure encountered on latest (2017-07-20) git://git.denx.de/u-boot-usb.git branch master for target ls1021atwr_nor_defconfig" -- Best regards, Marek Vasut _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot