This commit converts display5 board (also its 'factory' variant) to use
DM/DTS.
The change has been made in a single patch to avoid problems with
unbuildable commits (as DM conversion breaks some of them).
Notable changes (DM/DTS conversion):
- PINCTRL{_IMX6}
- DM_I2C
- enable 'regulator' and 'pmic' commands
- DM_MMC and BLK (USDHC)
- DM_ETH
- DM_SPI and DM_SPI_FLASH (but no in SPL)
- DM WDT (including SYSRESET)
- Update display5_factory_defconfig after switch to DM/DTS and uuu utility
Note regarding 'display5_factory_defconfig'
The VID and PID for SPL running SDP gadget have been updated to
allow seamless work with 'uuu' utility from NXP (the imx_usb doesn't work
properly after embedding the u-boot proper into fitImage - problem with IVT
embedding in FIT).
Example to use 'uuu' session:
cat << EOF > display5_recovery.lst
uuu_version 1.2.135
SDP: boot -f /srv/tftp/SPL
SDPU: write -f /srv/tftp/u-boot-dtb.img -addr 0x10000000
SDPU: jump -addr 0x10000000
SDPU: done
EOF
sudo ./uuu/uuu display5_recovery.lst
Signed-off-by: Lukasz Majewski <lu...@denx.de>
---
arch/arm/dts/imx6q-display5-u-boot.dtsi | 5 +
arch/arm/mach-imx/mx6/Kconfig | 5 +
board/liebherr/display5/common.c | 24 ----
board/liebherr/display5/common.h | 2 -
board/liebherr/display5/display5.c | 225 ++++----------------------------
configs/display5_defconfig | 29 ++++
configs/display5_factory_defconfig | 43 +++++-
include/configs/display5.h | 29 ++--
8 files changed, 115 insertions(+), 247 deletions(-)
diff --git a/arch/arm/dts/imx6q-display5-u-boot.dtsi
b/arch/arm/dts/imx6q-display5-u-boot.dtsi
index b942218b7a..aa660b5aeb 100644
--- a/arch/arm/dts/imx6q-display5-u-boot.dtsi
+++ b/arch/arm/dts/imx6q-display5-u-boot.dtsi
@@ -31,6 +31,11 @@
chosen {
stdout-path = &uart5;
};
+
+ wdt-reboot {
+ compatible = "wdt-reboot";
+ wdt = <&wdog1>;
+ };
};
&i2c3 {
diff --git a/arch/arm/mach-imx/mx6/Kconfig b/arch/arm/mach-imx/mx6/Kconfig
index f513c4c06f..da00cf611e 100644
--- a/arch/arm/mach-imx/mx6/Kconfig
+++ b/arch/arm/mach-imx/mx6/Kconfig
@@ -187,6 +187,11 @@ config TARGET_DHCOMIMX6
config TARGET_DISPLAY5
bool "LWN DISPLAY5 board"
select DM
+ select DM_ETH
+ select DM_I2C
+ select DM_MMC
+ select DM_SPI
+ select DM_GPIO
select DM_SERIAL
select SUPPORT_SPL
imply CMD_DM
diff --git a/board/liebherr/display5/common.c b/board/liebherr/display5/common.c
index 48b5c1a6f5..2b3253d88d 100644
--- a/board/liebherr/display5/common.c
+++ b/board/liebherr/display5/common.c
@@ -45,18 +45,6 @@ void displ5_set_iomux_misc_spl(void)
}
#ifdef CONFIG_MXC_SPI
-iomux_v3_cfg_t const ecspi_pads[] = {
- /* SPI3 */
- MX6_PAD_DISP0_DAT2__ECSPI3_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
- MX6_PAD_DISP0_DAT1__ECSPI3_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
- MX6_PAD_DISP0_DAT0__ECSPI3_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
- MX6_PAD_DISP0_DAT3__ECSPI3_SS0 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_DISP0_DAT4__ECSPI3_SS1 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_DISP0_DAT5__ECSPI3_SS2 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_DISP0_DAT6__ECSPI3_SS3 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_DISP0_DAT7__ECSPI3_RDY | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
iomux_v3_cfg_t const ecspi2_pads[] = {
/* SPI2, NOR Flash nWP, CS0 */
MX6_PAD_CSI0_DAT10__ECSPI2_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
@@ -79,14 +67,8 @@ void displ5_set_iomux_ecspi_spl(void)
SETUP_IOMUX_PADS(ecspi2_pads);
}
-void displ5_set_iomux_ecspi(void)
-{
- SETUP_IOMUX_PADS(ecspi_pads);
-}
-
#else
void displ5_set_iomux_ecspi_spl(void) {}
-void displ5_set_iomux_ecspi(void) {}
#endif
#ifdef CONFIG_FSL_ESDHC
@@ -109,12 +91,6 @@ void displ5_set_iomux_usdhc_spl(void)
SETUP_IOMUX_PADS(usdhc4_pads);
}
-void displ5_set_iomux_usdhc(void)
-{
- SETUP_IOMUX_PADS(usdhc4_pads);
-}
-
#else
void displ5_set_iomux_usdhc_spl(void) {}
-void displ5_set_iomux_usdhc(void) {}
#endif
diff --git a/board/liebherr/display5/common.h b/board/liebherr/display5/common.h
index 78c64b02e2..2bbd934e7a 100644
--- a/board/liebherr/display5/common.h
+++ b/board/liebherr/display5/common.h
@@ -34,9 +34,7 @@
void displ5_set_iomux_uart_spl(void);
void displ5_set_iomux_uart(void);
void displ5_set_iomux_ecspi_spl(void);
-void displ5_set_iomux_ecspi(void);
void displ5_set_iomux_usdhc_spl(void);
-void displ5_set_iomux_usdhc(void);
void displ5_set_iomux_misc_spl(void);
#endif /* __DISPL5_COMMON_H_ */
diff --git a/board/liebherr/display5/display5.c
b/board/liebherr/display5/display5.c
index 410d5bc782..6592f0c3ca 100644
--- a/board/liebherr/display5/display5.c
+++ b/board/liebherr/display5/display5.c
@@ -17,25 +17,14 @@
#include <asm/gpio.h>
#include <malloc.h>
#include <asm/mach-imx/iomux-v3.h>
-#include <asm/mach-imx/mxc_i2c.h>
#include <asm/mach-imx/boot_mode.h>
-#include <asm/mach-imx/spi.h>
-#include <mmc.h>
-#include <fsl_esdhc.h>
#include <miiphy.h>
-#include <netdev.h>
-#include <i2c.h>
#include <environment.h>
#include <dm.h>
#include <dm/platform_data/serial_mxc.h>
#include <dm/platdata.h>
-#ifndef CONFIG_MXC_SPI
-#error "CONFIG_SPI must be set for this board"
-#error "Please check your config file"
-#endif
-
#include "common.h"
DECLARE_GLOBAL_DATA_PTR;
@@ -119,49 +108,6 @@ int dram_init(void)
return 0;
}
-#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
-/* I2C1: TFA9879 */
-struct i2c_pads_info i2c_pad_info0 = {
- .scl = {
- .i2c_mode = MX6_PAD_EIM_D21__I2C1_SCL | PC,
- .gpio_mode = MX6_PAD_EIM_D21__GPIO3_IO21 | PC,
- .gp = IMX_GPIO_NR(3, 21)
- },
- .sda = {
- .i2c_mode = MX6_PAD_EIM_D28__I2C1_SDA | PC,
- .gpio_mode = MX6_PAD_EIM_D28__GPIO3_IO28 | PC,
- .gp = IMX_GPIO_NR(3, 28)
- }
-};
-
-/* I2C2: TIVO TM4C123 */
-struct i2c_pads_info i2c_pad_info1 = {
- .scl = {
- .i2c_mode = MX6_PAD_EIM_EB2__I2C2_SCL | PC,
- .gpio_mode = MX6_PAD_EIM_EB2__GPIO2_IO30 | PC,
- .gp = IMX_GPIO_NR(2, 30)
- },
- .sda = {
- .i2c_mode = MX6_PAD_EIM_D16__I2C2_SDA | PC,
- .gpio_mode = MX6_PAD_EIM_D16__GPIO3_IO16 | PC,
- .gp = IMX_GPIO_NR(3, 16)
- }
-};
-
-/* I2C3: PMIC PF0100, EEPROM AT24C256C */
-struct i2c_pads_info i2c_pad_info2 = {
- .scl = {
- .i2c_mode = MX6_PAD_EIM_D17__I2C3_SCL | PC,
- .gpio_mode = MX6_PAD_EIM_D17__GPIO3_IO17 | PC,
- .gp = IMX_GPIO_NR(3, 17)
- },
- .sda = {
- .i2c_mode = MX6_PAD_EIM_D18__I2C3_SDA | PC,
- .gpio_mode = MX6_PAD_EIM_D18__GPIO3_IO18 | PC,
- .gp = IMX_GPIO_NR(3, 18)
- }
-};
-
iomux_v3_cfg_t const misc_pads[] = {
/* Prod ID GPIO pins */
MX6_PAD_NANDF_D4__GPIO2_IO04 | MUX_PAD_CTRL(NO_PAD_CTRL),
@@ -186,174 +132,48 @@ iomux_v3_cfg_t const misc_pads[] = {
MX6_PAD_EIM_D29__GPIO3_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
-#ifdef CONFIG_FSL_ESDHC
-struct fsl_esdhc_cfg usdhc_cfg[1] = {
- { USDHC4_BASE_ADDR, 0, 8, },
-};
-
-int board_mmc_getcd(struct mmc *mmc)
+/*
+ * Do not overwrite the console
+ * Always use serial for U-Boot console
+ */
+int overwrite_console(void)
{
return 1;
}
-int board_mmc_init(bd_t *bis)
-{
- displ5_set_iomux_usdhc();
-
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
-
- return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
-}
-#endif /* CONFIG_FSL_ESDHC */
-
-static void displ5_setup_ecspi(void)
-{
- int ret;
-
- displ5_set_iomux_ecspi();
-
- ret = gpio_request(IMX_GPIO_NR(5, 29), "spi2_cs0");
- if (!ret)
- gpio_direction_output(IMX_GPIO_NR(5, 29), 1);
-
- ret = gpio_request(IMX_GPIO_NR(7, 0), "spi2_#wp");
- if (!ret)
- gpio_direction_output(IMX_GPIO_NR(7, 0), 1);
-}
-
-#ifdef CONFIG_FEC_MXC
-iomux_v3_cfg_t const enet_pads[] = {
- MX6_PAD_ENET_TXD1__ENET_1588_EVENT0_IN | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_RXD1__ENET_1588_EVENT3_OUT | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
-
- /* for old evalboard with R159 present and R160 not populated */
- MX6_PAD_GPIO_16__ENET_REF_CLK | MUX_PAD_CTRL(NO_PAD_CTRL),
-
- MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
-
- MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
- /*INT#_GBE*/
- MX6_PAD_ENET_TX_EN__GPIO1_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-static void setup_iomux_enet(void)
-{
- SETUP_IOMUX_PADS(enet_pads);
- gpio_direction_input(IMX_GPIO_NR(1, 28)); /*INT#_GBE*/
-}
-
-static int setup_mac_from_fuse(void)
+#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP)
+int ft_board_setup(void *blob, bd_t *bd)
{
- unsigned char enetaddr[6];
- int ret;
-
- ret = eth_env_get_enetaddr("ethaddr", enetaddr);
- if (ret) /* ethaddr is already set */
- return 0;
-
- imx_get_mac_from_fuse(0, enetaddr);
-
- if (is_valid_ethaddr(enetaddr)) {
- eth_env_set_enetaddr("ethaddr", enetaddr);
- return 0;
- }
-
+ fdt_fixup_ethernet(blob);
return 0;
}
+#endif
-int board_eth_init(bd_t *bd)
+int board_phy_config(struct phy_device *phydev)
{
- struct phy_device *phydev;
- struct mii_dev *bus;
- int ret;
-
- setup_iomux_enet();
-
- iomuxc_set_rgmii_io_voltage(DDR_SEL_1P5V_IO);
-
- ret = enable_fec_anatop_clock(0, ENET_125MHZ);
- if (ret)
- return ret;
-
- setup_mac_from_fuse();
-
- bus = fec_get_miibus(IMX_FEC_BASE, -1);
- if (!bus)
- return -ENODEV;
-
- /*
- * We use here the "rgmii-id" mode of operation and allow M88E1512
- * PHY to use its internally callibrated RX/TX delays
- */
- phydev = phy_find_by_mask(bus, 0xffffffff /* (0xf << 4) */,
- PHY_INTERFACE_MODE_RGMII_ID);
- if (!phydev) {
- ret = -ENODEV;
- goto err_phy;
- }
-
/* display5 due to PCB routing can only work with 100 Mbps */
phydev->advertising &= ~(ADVERTISED_1000baseX_Half |
ADVERTISED_1000baseX_Full |
SUPPORTED_1000baseT_Half |
SUPPORTED_1000baseT_Full);
- ret = fec_probe(bd, -1, IMX_FEC_BASE, bus, phydev);
- if (ret)
- goto err_sw;
+ if (phydev->drv->config)
+ return phydev->drv->config(phydev);
return 0;
-
-err_sw:
- free(phydev);
-err_phy:
- mdio_unregister(bus);
- free(bus);
- return ret;
}
-#endif /* CONFIG_FEC_MXC */
-
-/*
- * Do not overwrite the console
- * Always use serial for U-Boot console
- */
-int overwrite_console(void)
-{
- return 1;
-}
-
-#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP)
-int ft_board_setup(void *blob, bd_t *bd)
-{
- fdt_fixup_ethernet(blob);
- return 0;
-}
-#endif
int board_init(void)
{
+ int ret;
+
debug("board init\n");
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
/* Setup iomux for non console UARTS */
displ5_set_iomux_uart();
-
- displ5_setup_ecspi();
-
+ /* Setup misc (application specific) stuff */
SETUP_IOMUX_PADS(misc_pads);
get_board_id(gpio_table_sw_ids, &gpio_table_sw_ids_names[0],
@@ -369,9 +189,18 @@ int board_init(void)
udelay(25);
- setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info0);
- setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
- setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
+ /* Setup low level FEC (ETH) */
+ ret = gpio_request(IMX_GPIO_NR(1, 28), "INT_GBE");
+ if (!ret)
+ gpio_direction_input(IMX_GPIO_NR(1, 28)); /*INT#_GBE*/
+
+ iomuxc_set_rgmii_io_voltage(DDR_SEL_1P5V_IO);
+ enable_fec_anatop_clock(0, ENET_125MHZ);
+
+ /* Setup #WP for SPI-NOR memory */
+ ret = gpio_request(IMX_GPIO_NR(7, 0), "spi2_#wp");
+ if (!ret)
+ gpio_direction_output(IMX_GPIO_NR(7, 0), 1);
return 0;
}
diff --git a/configs/display5_defconfig b/configs/display5_defconfig
index 0ef56024e9..6fca4d059b 100644
--- a/configs/display5_defconfig
+++ b/configs/display5_defconfig
@@ -46,13 +46,17 @@ CONFIG_CMD_GPT=y
CONFIG_CMD_I2C=y
CONFIG_CMD_MMC=y
CONFIG_CMD_PART=y
+# CONFIG_CMD_PINMUX is not set
CONFIG_CMD_SF=y
CONFIG_CMD_SPI=y
+CONFIG_CMD_WDT=y
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_CACHE=y
CONFIG_CMD_TIME=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_EXT4=y
CONFIG_CMD_FAT=y
@@ -66,20 +70,45 @@ CONFIG_DEFAULT_DEVICE_TREE="imx6q-display5"
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_BOOTCOUNT_BOOTLIMIT=3
+CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
+CONFIG_I2C_DEFAULT_BUS_NUMBER=0x2
+CONFIG_SYS_I2C_MXC=y
+CONFIG_SYS_I2C_MXC_I2C1=y
+CONFIG_SYS_I2C_MXC_I2C2=y
+CONFIG_SYS_I2C_MXC_I2C3=y
+CONFIG_MISC=y
+CONFIG_I2C_EEPROM=y
+CONFIG_SYS_I2C_EEPROM_ADDR=0x50
+CONFIG_SYS_I2C_EEPROM_BUS=2
+CONFIG_SYS_EEPROM_SIZE=32768
+CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
+CONFIG_SYS_I2C_EEPROM_ADDR_LEN=2
CONFIG_SUPPORT_EMMC_BOOT=y
CONFIG_FSL_ESDHC=y
CONFIG_MTD_DEVICE=y
+CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
CONFIG_SF_DEFAULT_BUS=1
CONFIG_SF_DEFAULT_MODE=0
CONFIG_SF_DEFAULT_SPEED=50000000
+CONFIG_SPI_FLASH_SFDP_SUPPORT=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SPI_FLASH_MTD=y
CONFIG_PHYLIB=y
CONFIG_PHY_MARVELL=y
CONFIG_FEC_MXC=y
CONFIG_MII=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX6=y
+CONFIG_DM_PMIC=y
+CONFIG_DM_PMIC_PFUZE100=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_PFUZE100=y
CONFIG_MXC_UART=y
CONFIG_SPI=y
CONFIG_MXC_SPI=y
+CONFIG_SYSRESET=y
+CONFIG_SYSRESET_WATCHDOG=y
+CONFIG_I2C_EDID=y
CONFIG_IMX_WATCHDOG=y
diff --git a/configs/display5_factory_defconfig
b/configs/display5_factory_defconfig
index 0d9eed3a3e..aafeda437d 100644
--- a/configs/display5_factory_defconfig
+++ b/configs/display5_factory_defconfig
@@ -4,13 +4,19 @@ CONFIG_SYS_TEXT_BASE=0x17800000
CONFIG_SPL_GPIO_SUPPORT=y
CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_SYS_MALLOC_F_LEN=0x1000
+CONFIG_MX6_DDRCAL=y
CONFIG_TARGET_DISPLAY5=y
+CONFIG_SPL_MMC_SUPPORT=y
CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_SPL_SYS_MALLOC_F_LEN=0x400
CONFIG_NR_DRAM_BANKS=1
CONFIG_SPL=y
CONFIG_SPL_SPI_FLASH_SUPPORT=y
CONFIG_SPL_SPI_SUPPORT=y
+CONFIG_TPL_SYS_MALLOC_F_LEN=0x400
CONFIG_FIT=y
+CONFIG_SPL_LOAD_FIT=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg,MX6Q"
CONFIG_BOOTDELAY=3
@@ -20,7 +26,6 @@ CONFIG_SUPPORT_RAW_INITRD=y
CONFIG_MISC_INIT_R=y
CONFIG_BOUNCE_BUFFER=y
CONFIG_SPL_TEXT_BASE=0x00908000
-# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
# CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR is not set
CONFIG_SPL_DMA_SUPPORT=y
CONFIG_SPL_I2C_SUPPORT=y
@@ -46,11 +51,14 @@ CONFIG_CMD_PART=y
CONFIG_CMD_SF=y
CONFIG_CMD_SPI=y
CONFIG_CMD_USB_SDP=y
+CONFIG_CMD_WDT=y
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_CACHE=y
CONFIG_CMD_TIME=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_EXT4=y
CONFIG_CMD_EXT4_WRITE=y
@@ -61,30 +69,57 @@ CONFIG_MTDIDS_DEFAULT="nor0=02008000.spi.1"
CONFIG_MTDPARTS_DEFAULT="mtdparts=02008000.spi.1:128k(SPL),1m(u-boot),64k(env1),64k(env2),4m(swu-kernel),16m(swu-initramfs),1m(factory),-(reserved)"
# CONFIG_SPL_EFI_PARTITION is not set
CONFIG_PARTITION_TYPE_GUID=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="imx6q-display5"
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_DFU_MMC=y
CONFIG_DFU_SF=y
+CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
+CONFIG_I2C_DEFAULT_BUS_NUMBER=0x2
+CONFIG_SYS_I2C_MXC=y
+CONFIG_SYS_I2C_MXC_I2C1=y
+CONFIG_SYS_I2C_MXC_I2C2=y
+CONFIG_SYS_I2C_MXC_I2C3=y
+CONFIG_MISC=y
+CONFIG_I2C_EEPROM=y
+CONFIG_SYS_I2C_EEPROM_ADDR=0x50
+CONFIG_SYS_I2C_EEPROM_BUS=2
+CONFIG_SYS_EEPROM_SIZE=32768
+CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5
+CONFIG_SYS_I2C_EEPROM_ADDR_LEN=2
CONFIG_SUPPORT_EMMC_BOOT=y
CONFIG_FSL_ESDHC=y
CONFIG_MTD_DEVICE=y
+CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
CONFIG_SF_DEFAULT_BUS=1
CONFIG_SF_DEFAULT_MODE=0
CONFIG_SF_DEFAULT_SPEED=50000000
+CONFIG_SPI_FLASH_SFDP_SUPPORT=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SPI_FLASH_MTD=y
CONFIG_PHYLIB=y
+CONFIG_PHY_MARVELL=y
CONFIG_FEC_MXC=y
CONFIG_MII=y
+CONFIG_DM_PMIC=y
+CONFIG_DM_PMIC_PFUZE100=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_PFUZE100=y
CONFIG_MXC_UART=y
CONFIG_SPI=y
CONFIG_MXC_SPI=y
+CONFIG_SYSRESET=y
+CONFIG_SYSRESET_WATCHDOG=y
CONFIG_USB=y
+CONFIG_DM_USB=y
CONFIG_USB_GADGET=y
CONFIG_USB_GADGET_MANUFACTURER="Liebherr"
-CONFIG_USB_GADGET_VENDOR_NUM=0x1b67
-CONFIG_USB_GADGET_PRODUCT_NUM=0x4000
+CONFIG_USB_GADGET_VENDOR_NUM=0x0525
+CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
CONFIG_CI_UDC=y
CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_I2C_EDID=y
CONFIG_IMX_WATCHDOG=y
-CONFIG_OF_LIBFDT=y
+CONFIG_PANIC_HANG=y
diff --git a/include/configs/display5.h b/include/configs/display5.h
index 5dbe5b8528..c8218effc3 100644
--- a/include/configs/display5.h
+++ b/include/configs/display5.h
@@ -35,8 +35,11 @@
* 0x1540000 - 0x1640000 : SPI.factory (1MiB)
*/
-#ifndef CONFIG_SPL_BUILD
-#define CONFIG_SPI_FLASH_MTD
+/* SPI Flash Configs */
+#if defined(CONFIG_SPL_BUILD)
+#undef CONFIG_DM_SPI
+#undef CONFIG_DM_SPI_FLASH
+#undef CONFIG_SPI_FLASH_MTD
#endif
/* Below values are "dummy" - only to avoid build break */
@@ -58,23 +61,7 @@
#define CONFIG_MXC_UART_BASE UART5_BASE
/* I2C Configs */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_MXC
-#define CONFIG_SYS_I2C_MXC_I2C1
-#define CONFIG_SYS_I2C_MXC_I2C2
-#define CONFIG_SYS_I2C_MXC_I2C3
#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_I2C_SPEED 100000
-#define CONFIG_I2C_EDID
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-
-/* Ethernet */
-#ifdef CONFIG_FEC_MXC
-#define IMX_FEC_BASE ENET_BASE_ADDR
-#define CONFIG_FEC_XCV_TYPE RGMII
-#define CONFIG_ETHPRIME "FEC"
-#define CONFIG_FEC_MXC_PHYADDR 0
-#endif
/* MMC Configs */
#define CONFIG_FSL_USDHC
@@ -363,7 +350,11 @@
/* Watchdog */
#define CONFIG_WATCHDOG_TIMEOUT_MSECS 15000
-
+#if defined(CONFIG_SPL_BUILD)
+#undef CONFIG_WDT
+#undef CONFIG_WATCHDOG
+#define CONFIG_HW_WATCHDOG
+#endif
/* ENV config */
#ifdef CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_SIZE (SZ_64K)
--
2.11.0
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
