[PATCH v3 09/12] mmc: fsl_esdhc_imx: simplify esdhc_setup_data()

[Sean Anderson]

[ fsl_esdhc commit 7e48a028a42c111ba38a90b86e5f57dace980fa0 ]

First, we need the waterlevel setting for PIO mode only. Secondy, both DMA
setup code is identical for both directions, except for the data pointer.
Thus, unify them.

Signed-off-by: Michael Walle <mich...@walle.cc>
Signed-off-by: Sean Anderson <sean.ander...@seco.com>
Reviewed-by: Jaehoon Chung <jh80.ch...@samsung.com>
---

(no changes since v1)

 drivers/mmc/fsl_esdhc_imx.c | 89 ++++++++++++++++++++++---------------
 1 file changed, 52 insertions(+), 37 deletions(-)

diff --git a/drivers/mmc/fsl_esdhc_imx.c b/drivers/mmc/fsl_esdhc_imx.c
index 283af35a81..6c25a77c79 100644
--- a/drivers/mmc/fsl_esdhc_imx.c
+++ b/drivers/mmc/fsl_esdhc_imx.c
@@ -279,59 +279,74 @@ static void esdhc_pio_read_write(struct fsl_esdhc_priv 
*priv,
 }
 #endif
 
-static int esdhc_setup_data(struct fsl_esdhc_priv *priv, struct mmc *mmc,
-                           struct mmc_data *data)
+#ifdef CONFIG_SYS_FSL_ESDHC_USE_PIO
+static void esdhc_setup_watermark_level(struct fsl_esdhc_priv *priv,
+                                       struct mmc_data *data)
 {
-       int timeout;
-       uint trans_bytes = data->blocksize * data->blocks;
        struct fsl_esdhc *regs = priv->esdhc_regs;
-       uint wml_value;
-
-       wml_value = data->blocksize/4;
+       uint wml_value = data->blocksize / 4;
 
        if (data->flags & MMC_DATA_READ) {
                if (wml_value > WML_RD_WML_MAX)
                        wml_value = WML_RD_WML_MAX_VAL;
 
                esdhc_clrsetbits32(&regs->wml, WML_RD_WML_MASK, wml_value);
-#ifndef CONFIG_SYS_FSL_ESDHC_USE_PIO
-               priv->dma_addr = dma_map_single(data->dest, trans_bytes,
-                                               mmc_get_dma_dir(data));
-               if (upper_32_bits(priv->dma_addr))
-                       printf("Cannot use 64 bit addresses with SDMA\n");
-               esdhc_write32(&regs->dsaddr, lower_32_bits(priv->dma_addr));
-#endif
        } else {
                if (wml_value > WML_WR_WML_MAX)
                        wml_value = WML_WR_WML_MAX_VAL;
-               if (priv->wp_enable) {
-                       if ((esdhc_read32(&regs->prsstat) &
-                           PRSSTAT_WPSPL) == 0) {
-                               printf("\nThe SD card is locked. Can not write 
to a locked card.\n\n");
-                               return -ETIMEDOUT;
-                       }
-               } else {
-#if CONFIG_IS_ENABLED(DM_GPIO)
-                       if (dm_gpio_is_valid(&priv->wp_gpio) &&
-                           dm_gpio_get_value(&priv->wp_gpio)) {
-                               printf("\nThe SD card is locked. Can not write 
to a locked card.\n\n");
-                               return -ETIMEDOUT;
-                       }
-#endif
-               }
 
                esdhc_clrsetbits32(&regs->wml, WML_WR_WML_MASK,
-                                       wml_value << 16);
-#ifndef CONFIG_SYS_FSL_ESDHC_USE_PIO
-               priv->dma_addr = dma_map_single((void *)data->src, trans_bytes,
-                                               mmc_get_dma_dir(data));
-               if (upper_32_bits(priv->dma_addr))
-                       printf("Cannot use 64 bit addresses with SDMA\n");
-               esdhc_write32(&regs->dsaddr, lower_32_bits(priv->dma_addr));
-#endif
+                                  wml_value << 16);
        }
+}
+#endif
 
+static void esdhc_setup_dma(struct fsl_esdhc_priv *priv, struct mmc_data *data)
+{
+       uint trans_bytes = data->blocksize * data->blocks;
+       struct fsl_esdhc *regs = priv->esdhc_regs;
+       void *buf;
+
+       if (data->flags & MMC_DATA_WRITE)
+               buf = (void *)data->src;
+       else
+               buf = data->dest;
+
+       priv->dma_addr = dma_map_single(buf, trans_bytes,
+                                       mmc_get_dma_dir(data));
+       if (upper_32_bits(priv->dma_addr))
+               printf("Cannot use 64 bit addresses with SDMA\n");
+       esdhc_write32(&regs->dsaddr, lower_32_bits(priv->dma_addr));
        esdhc_write32(&regs->blkattr, data->blocks << 16 | data->blocksize);
+}
+
+static int esdhc_setup_data(struct fsl_esdhc_priv *priv, struct mmc *mmc,
+                           struct mmc_data *data)
+{
+       int timeout;
+       bool is_write = data->flags & MMC_DATA_WRITE;
+       struct fsl_esdhc *regs = priv->esdhc_regs;
+
+       if (is_write) {
+               if (priv->wp_enable && !(esdhc_read32(&regs->prsstat) & 
PRSSTAT_WPSPL)) {
+                       printf("Cannot write to locked SD card.\n");
+                       return -EINVAL;
+               } else {
+#if CONFIG_IS_ENABLED(DM_GPIO)
+                       if (dm_gpio_is_valid(&priv->wp_gpio) &&
+                           dm_gpio_get_value(&priv->wp_gpio)) {
+                               printf("Cannot write to locked SD card.\n");
+                               return -EINVAL;
+                       }
+#endif
+               }
+       }
+
+#ifdef CONFIG_SYS_FSL_ESDHC_USE_PIO
+       esdhc_setup_watermark_level(priv, data);
+#else
+       esdhc_setup_dma(priv, data);
+#endif
 
        /* Calculate the timeout period for data transactions */
        /*
-- 
2.25.1