Hi Filip, On Mon, 19 Dec 2022 at 02:29, Filip Žaludek <filip.zalu...@oracle.com> wrote: > > > > Hi Simon, > > is your testing framework connected to HDMI? Only notable discrepancy > from generic config is enabled 'efidebug' command. > > > Tested more (cycled 'U-Boot>' and 'reset'), both RPi3B and RPi3B+.. > USB Keyboard failure rates: > connected console 02/10 > connected hdmi 06/10 > connected console + hdmi 07/10 > ** USB Keyboard always detected by 'usb info', just does not respond. > > USB Keyboard failure rates, reverted 96991e652f541323a03c5b7e075d54a117091618: > connected console + hdmi 00/10
Yes this one does have HDMI. Are you wanting me to run multiple runs? With or without the display? Regards, Simon > > > > Just to note subsequent Grub2 menu redraw to my 180x50 console terminal > is about 5x faster when hdmi disconnected. > > > > Thanks for testing! > Regards, > Filip > > > > FW: rpi-firmware-20220830-1.0.1.el8.noarch > Revision: 9bd3d354a1a0712ac27c717df9ad60566b0406ee > > > > > > > > On 12/17/22 23:24, Simon Glass wrote: > > Hi Filip, > > > > On Sat, 17 Dec 2022 at 05:50, Filip Žaludek <filip.zalu...@oracle.com> > > wrote: > >> > >> > >> > >> Hello, > >> change seems to be unfriendly to RPi3B+, it allows to enter 'U-Boot>' > >> shell but usb keyboard > >> does not respond. Keyboard is detected by 'usb info' in v2023.01-rc3, not > >> in v2022.10. > >> When reverted, usb keyboard works as expected. > >> > >> Anybody sitting front of RPi3B+ care to confirm? > >> > >> > >> Regards, > >> Filip > >> > >> > >> > >> > >> > >> Patch: > >> https://urldefense.com/v3/__https://github.com/u-boot/u-boot/commit/96991e652f541323a03c5b7e075d54a117091618__;!!ACWV5N9M2RV99hQ!MunypRlNhelLw1nrbbLFCTeZK2pCAlIH_WPhgvmgFhfy3wJnPA5titNwl3o2fkc-mCqWAgJxjjc1sSD1$ > >> > >> > >> Debug: > >> USB KBD: found interrupt EP: 0x81 > >> USB KBD: set boot protocol > >> dwc2_submit_control_msg: dev='usb@7e980000', udev=000000003af4be00, > >> udev->dev='usb_kbd', portnr=3 > >> USB KBD: set idle interval... > >> dwc2_submit_control_msg: dev='usb@7e980000', udev=000000003af4be00, > >> udev->dev='usb_kbd', portnr=3 > >> USB KBD: enable interrupt pipe... > >> usb_kbd usb_kbd: Timeout poll on interrupt endpoint > >> > >> > >> Tested: > >> SW: v2022.10 & v2023.01-rc3 compiled from sources as 'rpiarm64' > >> HW: USB 1.1 and 2.0 keyboards, RPi3B+ > >> JeOS: > >> https://urldefense.com/v3/__http://download.opensuse.org/ports/aarch64/tumbleweed/appliances/openSUSE-Tumbleweed-ARM-JeOS-raspberrypi.aarch64-2022.10.11-Snapshot20221112.raw.xz__;!!ACWV5N9M2RV99hQ!MunypRlNhelLw1nrbbLFCTeZK2pCAlIH_WPhgvmgFhfy3wJnPA5titNwl3o2fkc-mCqWAgJxjkilUmrv$ > >> (u-boot-rpiarm64-2022.10-1.1.aarch64) > >> > >> > > > > This seems to work on current master: > > > > do-try-int.sh rpi3 > > Revision 9bd3d354a1a0712ac27c717df9ad60566b0406ee, board rpi3 > > > > Checking revision 9bd3d354a1a0712ac27c717df9ad60566b0406ee > > /vid/software/devel/ubtest > > tbot starting ... > > ├─Parameters: > > │ rev = '9bd3d354a1a0712ac27c717df9ad60566b0406ee' > > │ clean = False > > ├─Calling uboot_build_and_flash ... > > │ ├─Calling uboot_build ... > > │ │ ├─Calling uboot_checkout ... > > │ │ │ ├─Builder: rpi3 > > │ │ │ └─Done. (0.181s) > > │ │ ├─Configuring build ... > > │ │ ├─Calling uboot_make ... > > │ │ │ └─Done. (1.504s) > > │ │ └─Done. (2.178s) > > │ ├─Calling uboot_flash ... > > │ │ ├─Calling copy ... > > │ │ │ └─Done. (0.004s) > > │ │ └─Done. (1.119s) > > │ └─Done. (3.663s) > > ├───────────────────────────────────────── > > └─SUCCESS (3.799s) > > tbot starting ... > > ├─Calling interactive_board ... > > │ ├─POWERON (rpi3) > > │ ├─Entering interactive shell (CTRL+D to exit) ... > > > > > > U-Boot 2023.01-rc3-00057-g9bd3d354a1a (Dec 17 2022 - 15:23:14 -0700) > > > > DRAM: 992 MiB > > RPI 3 Model B (0xa22082) > > Core: 66 devices, 14 uclasses, devicetree: embed > > MMC: mmc@7e202000: 0, mmc@7e300000: 1 > > Loading Environment from FAT... Unable to read "uboot.env" from mmc0:1... > > In: serial > > Out: vidconsole > > Err: vidconsole > > Net: No ethernet found. > > starting USB... > > Bus usb@7e980000: USB DWC2 > > scanning bus usb@7e980000 for devices... usb_kbd usb_kbd: Timeout poll > > on interrupt endpoint > > Failed to get keyboard state from device 0c40:8000 > > 6 USB Device(s) found > > scanning usb for storage devices... 1 Storage Device(s) found > > Hit any key to stop autoboot: 0 > > U-Boot> usb info > > 1: Hub, USB Revision 1.10 > > - U-Boot Root Hub > > - Class: Hub > > - PacketSize: 8 Configurations: 1 > > - Vendor: 0x0000 Product 0x0000 Version 0.0 > > Configuration: 1 > > - Interfaces: 1 Self Powered 0mA > > Interface: 0 > > - Alternate Setting 0, Endpoints: 1 > > - Class Hub > > - Endpoint 1 In Interrupt MaxPacket 2 Interval 255ms > > > > 2: Hub, USB Revision 2.0 > > - Class: Hub > > - PacketSize: 64 Configurations: 1 > > - Vendor: 0x0424 Product 0x9514 Version 2.0 > > Configuration: 1 > > - Interfaces: 1 Self Powered Remote Wakeup 2mA > > Interface: 0 > > - Alternate Setting 0, Endpoints: 1 > > - Class Hub > > - Endpoint 1 In Interrupt MaxPacket 1 Interval 12ms > > - Endpoint 1 In Interrupt MaxPacket 1 Interval 12ms > > > > 3: Human Interface, USB Revision 1.10 > > - Logitech USB Keyboard > > - Class: (from Interface) Human Interface > > - PacketSize: 8 Configurations: 1 > > - Vendor: 0x046d Product 0xc31c Version 100.0 > > Configuration: 1 > > - Interfaces: 2 Bus Powered Remote Wakeup 90mA > > - String: "U64.00_B0001" > > Interface: 0 > > - Alternate Setting 0, Endpoints: 1 > > - Class Human Interface, Subclass: Boot Keyboard > > - String: "USB Keyboard" > > - Endpoint 1 In Interrupt MaxPacket 8 Interval 10ms > > Interface: 1 > > - Alternate Setting 0, Endpoints: 1 > > - Class Human Interface, Subclass: None > > - String: "USB Keyboard" > > - Endpoint 2 In Interrupt MaxPacket 4 Interval 255ms > > > > 4: Human Interface, USB Revision 0.1 > > - QDtech MPI5001 ? > > - Class: (from Interface) Human Interface > > - PacketSize: 64 Configurations: 1 > > - Vendor: 0x0483 Product 0x5750 Version 2.0 > > Configuration: 1 > > - Interfaces: 1 Bus Powered 64mA > > Interface: 0 > > - Alternate Setting 0, Endpoints: 1 > > - Class Human Interface, Subclass: None > > - Endpoint 2 In Interrupt MaxPacket 64 Interval 1ms > > - Endpoint 2 Out Interrupt MaxPacket 64 Interval 1ms > > > > 5: Vendor specific, USB Revision 2.0 > > - Class: Vendor specific > > - PacketSize: 64 Configurations: 1 > > - Vendor: 0x0424 Product 0xec00 Version 2.0 > > Configuration: 1 > > - Interfaces: 1 Self Powered Remote Wakeup 2mA > > Interface: 0 > > - Alternate Setting 0, Endpoints: 3 > > - Class Vendor specific > > - Endpoint 1 In Bulk MaxPacket 512 > > - Endpoint 2 Out Bulk MaxPacket 512 > > - Endpoint 3 In Interrupt MaxPacket 16 Interval 4ms > > > > 6: Mass Storage, USB Revision 2.10 > > - SanDisk USB Extreme Pro 513456791960 > > - Class: (from Interface) Mass Storage > > - PacketSize: 64 Configurations: 1 > > - Vendor: 0x0781 Product 0x5588 Version 1.0 > > Configuration: 1 > > - Interfaces: 1 Self Powered 0mA > > Interface: 0 > > - Alternate Setting 0, Endpoints: 2 > > - Class Mass Storage, Transp. SCSI, Bulk only > > - Endpoint 1 In Bulk MaxPacket 512 > > - Endpoint 2 Out Bulk MaxPacket 512 > > > > U-Boot> hello > > Unknown command 'hello' - try 'help' > > U-Boot> > > │ ├─POWEROFF (rpi3) > > │ ├─Exiting poweroff > > │ └─Done. (34.381s) > > ├───────────────────────────────────────── > > └─SUCCESS (34.481s) > > > > (the 'hello' is typed on the keyboard) > > > > Regards, > > Simon