On 2011/03/18 6:02 AM, Aaron Williams wrote: > Hi, > > I am running into issues in that the CFI code is broken for flash with an 8- > bit bus. The problem is that the CFI code uses the wrong addresses for 8-bits > vs 16-bits. > > The CFI function flash_map incorrectly calculates the byte offset with > Spansion flash. > > In our case, we have an 8-bit Spansion S29GL-N MirrorBit flash chip on an 8- > bit bus. > > According to the data sheet, in 8-bit mode the first unlock address is 0xAAA > and the second is 0x555. Basically all of the addresses are approximately > double what they are in 16-bit mode. > > Most of the addresses in the CFI code are wrong for 8-bit mode. > > They should be as follows: > unlock1: 0xAAA > unlock2: 0x555 > CFI Query: 0xAA > > Offset Device ID: 0x02, 0x1c, 0x1e > Offset Silicon Sector Factory Protect: 0x6 > Sector protect verify (sector address) + 4 > > The problem is that the dectection code detects (incorrectly) that we're an 8- > bit device on a 16-bit bus when in fact it's an 8-bit bus. > > For 16-bits, it's: > > unlock1: 0x555 > unlock2: 0x2aa > CFI Query: 0x55 > Offset Device ID: 0x1, 0x0e, 0x0f > > Now, in 16-bit mode these addresses should be effectively doubled so they > should look to be the same to software as I understand it. > > This is all taken from the datasheet. > > Note that the CFI code works fine with the flash hooked up as 16-bit on a 16- > bit bus. > > If it's an 8-bit flash on a 16-bit bus then the addresses should be doubled. >
> > -Aaron Hi Aaron, Does this patch (originally by Stefan Roese) work for you? I also need it for the DNS323 port. FWIW, mine is also a Spansion flash (S29GL064M90TFIR4), although I am not 100% sure of the layout and connectivity. Rogan --- drivers/mtd/cfi_flash.c | 22 +++++++++++++++++++++- 1 files changed, 21 insertions(+), 1 deletions(-) diff --git a/drivers/mtd/cfi_flash.c b/drivers/mtd/cfi_flash.c index dd394a8..74e9ade 100644 --- a/drivers/mtd/cfi_flash.c +++ b/drivers/mtd/cfi_flash.c @@ -291,6 +291,9 @@ static inline uchar flash_read_uchar (flash_info_t * info, uint offset) uchar *cp; uchar retval; +#if 1 // test-only + offset = offset * 2; +#endif cp = flash_map (info, 0, offset); #if defined(__LITTLE_ENDIAN) || defined(CONFIG_SYS_WRITE_SWAPPED_DATA) retval = flash_read8(cp); @@ -308,6 +311,9 @@ static inline ushort flash_read_word (flash_info_t * info, uint offset) { ushort *addr, retval; +#if 1 // test-only + offset = offset * 2; +#endif addr = flash_map (info, 0, offset); retval = flash_read16 (addr); flash_unmap (info, 0, offset, addr); @@ -328,6 +334,9 @@ static ulong flash_read_long (flash_info_t * info, flash_sect_t sect, #ifdef DEBUG int x; #endif +#if 1 // test-only + offset = offset * 2; +#endif addr = flash_map (info, sect, offset); #ifdef DEBUG @@ -363,6 +372,9 @@ void flash_write_cmd (flash_info_t * info, flash_sect_t sect, void *addr; cfiword_t cword; +#if 1 // test-only + offset = offset * 2; +#endif addr = flash_map (info, sect, offset); flash_make_cmd (info, cmd, &cword); switch (info->portwidth) { @@ -420,6 +432,9 @@ static int flash_isequal (flash_info_t * info, flash_sect_t sect, cfiword_t cword; int retval; +#if 1 // test-only + offset = offset * 2; +#endif addr = flash_map (info, sect, offset); flash_make_cmd (info, cmd, &cword); @@ -1762,6 +1777,7 @@ static int __flash_detect_cfi (flash_info_t * info, struct cfi_qry *qry) info->addr_unlock1 = 0x555; info->addr_unlock2 = 0x2aa; +#if 0 // test-only /* * modify the unlock address if we are * in compatibility mode @@ -1776,6 +1792,7 @@ static int __flash_detect_cfi (flash_info_t * info, struct cfi_qry *qry) info->addr_unlock1 = 0xaaa; info->addr_unlock2 = 0x555; } +#endif info->name = "CFI conformant"; return 1; @@ -1942,11 +1959,13 @@ ulong flash_get_size (phys_addr_t base, int banknum) debug ("cfi version is 0x%04x\n", info->cfi_version); size_ratio = info->portwidth / info->chipwidth; +#if 0 // test-only /* if the chip is x8/x16 reduce the ratio by half */ if ((info->interface == FLASH_CFI_X8X16) && (info->chipwidth == FLASH_CFI_BY8)) { size_ratio >>= 1; } +#endif debug ("size_ratio %d port %d bits chip %d bits\n", size_ratio, info->portwidth << CFI_FLASH_SHIFT_WIDTH, info->chipwidth << CFI_FLASH_SHIFT_WIDTH); @@ -2034,12 +2053,13 @@ ulong flash_get_size (phys_addr_t base, int banknum) /* round up when converting to ms */ info->write_tout = (tmp + 999) / 1000; info->flash_id = FLASH_MAN_CFI; +#if 0 if ((info->interface == FLASH_CFI_X8X16) && (info->chipwidth == FLASH_CFI_BY8)) { /* XXX - Need to test on x8/x16 in parallel. */ info->portwidth >>= 1; } - +#endif flash_write_cmd (info, 0, 0, info->cmd_reset); } -- 1.7.1 _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot