Re: [PATCH v1 05/12] mtd: spi-nand: add EN75 BMT bad-block management support

[Tom Rini]

On Wed, Aug 26, 2026 at 04:12:00AM +0530, AK Sharma wrote:

> Add read support for the EcoNet/Airoha BMT/BBT (bad-block management
> table) layout used by the EN75xx vendor bootloaders, so U-Boot maps the
> SPI-NAND logical blocks the same way as the vendor firmware.
> 
> Signed-off-by: AK Sharma <maskacho...@yahoo.com>
> ---
>  drivers/mtd/nand/spi/Kconfig    |   8 +
>  drivers/mtd/nand/spi/Makefile   |   1 +
>  drivers/mtd/nand/spi/core.c     |   9 +-
>  drivers/mtd/nand/spi/en75_bmt.c | 665 ++++++++++++++++++++++++++++++++
>  drivers/mtd/nand/spi/en75_bmt.h |  24 ++
>  5 files changed, 706 insertions(+), 1 deletion(-)
>  create mode 100644 drivers/mtd/nand/spi/en75_bmt.c
>  create mode 100644 drivers/mtd/nand/spi/en75_bmt.h
> 
> diff --git a/drivers/mtd/nand/spi/Kconfig b/drivers/mtd/nand/spi/Kconfig
> index 1124dada..09531914 100644
> --- a/drivers/mtd/nand/spi/Kconfig
> +++ b/drivers/mtd/nand/spi/Kconfig
> @@ -6,3 +6,11 @@ menuconfig MTD_SPI_NAND
>       select SPI_MEM
>       help
>         This is the framework for the SPI NAND device drivers.
> +
> +config MTD_EN75_BMT
> +     bool "EcoNet EN75xx vendor BMT/BBT translation (read-only)"
> +     depends on MTD_SPI_NAND
> +     help
> +       Honour the EcoNet/Airoha factory BBT and BMT so logical NAND
> +       addresses match the bootbase and Linux. Read-only: never rewrite
> +       the tables.
> diff --git a/drivers/mtd/nand/spi/Makefile b/drivers/mtd/nand/spi/Makefile
> index a7a0b2cb..20aa718d 100644
> --- a/drivers/mtd/nand/spi/Makefile
> +++ b/drivers/mtd/nand/spi/Makefile
> @@ -1,6 +1,7 @@
>  # SPDX-License-Identifier: GPL-2.0
>  
>  spinand-objs := core.o otp.o
> +spinand-objs += $(if $(CONFIG_MTD_EN75_BMT),en75_bmt.o)
>  spinand-objs += alliancememory.o ato.o esmt.o fmsh.o foresee.o gigadevice.o 
> macronix.o
>  spinand-objs += micron.o paragon.o skyhigh.o toshiba.o winbond.o xtx.o
>  obj-$(CONFIG_MTD_SPI_NAND) += spinand.o
> diff --git a/drivers/mtd/nand/spi/core.c b/drivers/mtd/nand/spi/core.c
> index 14af4264..29fdefe2 100644
> --- a/drivers/mtd/nand/spi/core.c
> +++ b/drivers/mtd/nand/spi/core.c
> @@ -33,6 +33,7 @@
>  #include <linux/mtd/spinand.h>
>  #include <linux/printk.h>
>  #include <linux/delay.h>
> +#include "en75_bmt.h"
>  #endif
>  
>  struct spinand_plat {
> @@ -1703,15 +1704,21 @@ static int spinand_probe(struct udevice *dev)
>  #ifndef __UBOOT__
>       ret = mtd_device_register(mtd, NULL, 0);
>  #else
> +     ret = en75_bmt_attach(mtd);
> +     if (ret)
> +             goto err_spinand_cleanup;
> +
>       ret = add_mtd_device(mtd);
>  #endif
>       if (ret)
> -             goto err_spinand_cleanup;
> +             goto err_bmt_detach;
>  
>       plat->mtd = mtd;
>  
>       return 0;
>  
> +err_bmt_detach:
> +     en75_bmt_detach(mtd);
>  err_spinand_cleanup:
>       spinand_cleanup(spinand);

I am concerned about generic code path changes here, how is this handled
in the upstream kernel?

-- 
Tom

signature.asc
Description: PGP signature