Since the minimal ubuntu boots, I used its boot.src (I edited to refer
to correct memory locations):
--------------------------------------------------
if test "${beaglerev}" = "xMA"; then
echo "Kernel is not ready for 1Ghz limiting to 800Mhz"
setenv mpurate 800
fi
setenv dvimode 1280x720mr...@60
setenv vram 12MB
setenv bootcmd 'mmc init; fatload mmc 0:1 0x80000000 uImage; fatload mmc 0:1
0x81600000 uInitrd; bootm 0x80000000 0x81600000'
setenv bootargs 'console=ttyS2,115200n8 console=tty0 root=/dev/mmcblk0p2
rootwait ro vram=${vram} omapfb.mode=tv:pal omapdss.def_disp=tv fixrtc
buddy=unknown'
boot
--------------------------------------------------
I guess the 800Mhz limit is part of the problem, because now I can boot
up to:
--------------------------------------------------
Beagle xM Rev A
Reading boot sector
Loading u-boot.bin from mmc
U-Boot 2010.09-rc1 (Sep 23 2010 - 11:20:00)
OMAP3630/3730-GP ES1.0, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz
OMAP3 Beagle board + LPDDR/NAND
I2C: ready
DRAM: 512 MiB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Beagle xM Rev A
Die ID #528e00001bf00000015739ea0702900b
Hit any key to stop autoboot: 0
mmc1 is available
Unknown command 'userbutton' - try 'help'
reading boot.scr
530 bytes read
Running bootscript from mmc ...
## Executing script at 80200000
Kernel is not ready for 1Ghz limiting to 800Mhz
mmc1 is available
reading uImage
3687812 bytes read
reading uInitrd
6769443 bytes read
## Booting kernel from Legacy Image at 80000000 ...
Image Name: Ubuntu Kernel
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3687748 Bytes = 3.5 MiB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 81600000 ...
Image Name: Ubuntu Initrd
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 6769379 Bytes = 6.5 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.35-22-omap (bui...@gourd) (gcc version 4.4.5
(Ubuntu/Linaro 4)
[ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction
cache
[ 0.000000] Machine: OMAP3 Beagle Board
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] OMAP3630 ES1.0 (l2cache iva sgx neon isp 192mhz_clk )
[ 0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000
[ 0.000000] Reserving 6291456 bytes SDRAM for VRAM
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total
pages: 130048
[ 0.000000] Kernel command line: console=ttyS2,115200n8 console=tty0
root=/dev/mmcblk0p2 ron
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] allocated 2621440 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want
memory cgroups
[ 0.000000] Memory: 512MB = 512MB total
[ 0.000000] Memory: 496164k/496164k available, 28124k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
[ 0.000000] vmalloc : 0xe0800000 - 0xf8000000 ( 376 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .init : 0xc0008000 - 0xc0044000 ( 240 kB)
[ 0.000000] .text : 0xc0044000 - 0xc06ac000 (6560 kB)
[ 0.000000] .data : 0xc0718000 - 0xc0767960 ( 319 kB)
[ 0.000000] SLUB: Genslabs=9, HWalign=64, Order=0-3, MinObjects=0, CPUs=1,
Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] Verbose stalled-CPUs detection is disabled.
[ 0.000000] NR_IRQS:402
[ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/600 MHz
[ 0.000000] (null): no physical address for uart#3, so skipping
early_init...
[ 0.000000] omap_hwmod: l3_hwmod: cannot be enabled (3)
[ 0.000000] omap_hwmod: l4_core_hwmod: cannot be enabled (3)
[ 0.000000] omap_hwmod: l4_per_hwmod: cannot be enabled (3)
[ 0.000000] omap_hwmod: l4_wkup_hwmod: cannot be enabled (3)
[ 0.000000] Reprogramming SDRC clock to 332000000 Hz
[ 0.000000] GPMC revision 5.0
[ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96
interrupts
[ 0.000000] Total of 96 interrupts on 1 active controller
[ 0.000000] OMAP GPIO hardware version 2.5
[ 0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [tty0] enabled
[ 0.000000] Calibrating delay loop... 510.47 BogoMIPS (lpj=1994752)
[ 0.000000] pid_max: default: 32768 minimum: 301
[ 0.000000] Security Framework initialized
[ 0.000000] AppArmor: AppArmor initialized
[ 0.000000] Yama: becoming mindful.
[ 0.000000] Mount-cache hash table entries: 512
[ 0.000000] Initializing cgroup subsys ns
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Initializing cgroup subsys memory
[ 0.000000] Initializing cgroup subsys devices
[ 0.000000] Initializing cgroup subsys freezer
[ 0.000000] CPU: Testing write buffer coherency: ok
[ 0.000000] devtmpfs: initialized
[ 0.000000] regulator: core version 0.5
[ 0.000000] NET: Registered protocol family 16
[ 0.000000] OMAP3 Beagle Rev: xM
[ 0.000000] ------------[ cut here ]------------
[ 0.000000] WARNING: at
/build/buildd/linux-2.6.35/arch/arm/mach-omap2/serial.c:727 omap_se)
[ 0.000000] (null): can't init uart3, no clocks available
[ 0.000000] Modules linked in:
[ 0.000000] [<c004c508>] (unwind_backtrace+0x0/0x100) from [<c05142e8>]
(dump_stack+0x18/0x)
[ 0.000000] [<c05142e8>] (dump_stack+0x18/0x1c) from [<c0081bb8>]
(warn_slowpath_common+0x5)
[ 0.000000] [<c0081bb8>] (warn_slowpath_common+0x5c/0x6c) from [<c0081c6c>]
(warn_slowpath_)
[ 0.000000] [<c0081c6c>] (warn_slowpath_fmt+0x38/0x40) from [<c0010814>]
(omap_serial_init_)
[ 0.000000] [<c0010814>] (omap_serial_init_port+0x88/0x1f8) from
[<c00109b4>] (omap_serial_)
[ 0.000000] [<c00109b4>] (omap_serial_init+0x30/0x3c) from [<c00125e0>]
(omap3_beagle_init+)
[ 0.000000] [<c00125e0>] (omap3_beagle_init+0x6c/0xfc) from [<c000c660>]
(customize_machine)
[ 0.000000] [<c000c660>] (customize_machine+0x24/0x2c) from [<c00443bc>]
(do_one_initcall+0)
[ 0.000000] [<c00443bc>] (do_one_initcall+0x3c/0x1dc) from [<c00085b4>]
(do_basic_setup+0x6)
[ 0.000000] [<c00085b4>] (do_basic_setup+0x64/0x74) from [<c0008654>]
(kernel_init+0x90/0x1)
[ 0.000000] [<c0008654>] (kernel_init+0x90/0x120) from [<c0045af4>]
(kernel_thread_exit+0x0)
[ 0.000000] ---[ end trace da227214a82491b7 ]---
[ 0.000000] Found NAND on CS0
[ 0.000000] Registering NAND on CS0
[ 0.000000] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5
counters available
[ 0.000091] OMAP DMA hardware revision 5.0
[ 0.004486] bio: create slab <bio-0> at 0
[ 0.006164] SCSI subsystem initialized
[ 0.006805] usbcore: registered new interface driver usbfs
[ 0.006896] usbcore: registered new interface driver hub
[ 0.007080] usbcore: registered new device driver usb
[ 0.007415] i2c_omap i2c_omap.1: bus 1 rev4.0 at 2600 kHz
[ 0.009704] twl4030: PIH (irq 7) chaining IRQs 368..375
[ 0.009765] twl4030: power (irq 373) chaining IRQs 376..383
[ 0.010162] twl4030: gpio (irq 368) chaining IRQs 384..401
[ 0.012237] regulator: VUSB1V5: 1500 mV normal standby
[ 0.012603] regulator: VUSB1V8: 1800 mV normal standby
[ 0.012908] regulator: VUSB3V1: 3100 mV normal standby
[ 0.014221] twl4030_usb twl4030_usb: Initialized TWL4030 USB module
[ 0.014862] regulator: VMMC1: 1850 <--> 3150 mV at 3000 mV normal standby
[ 0.015197] regulator: VDAC: 1800 mV normal standby
[ 0.015655] regulator: VPLL2: 1800 mV normal standby
[ 0.016052] regulator: VSIM: 1800 <--> 3000 mV at 1800 mV normal standby
[ 0.024902] i2c_omap i2c_omap.3: bus 3 rev4.0 at 100 kHz
[ 0.025756] Advanced Linux Sound Architecture Driver Version 1.0.23.
[ 0.026275] NetLabel: Initializing
[ 0.026306] NetLabel: domain hash size = 128
[ 0.026336] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.026428] NetLabel: unlabeled traffic allowed by default
[ 0.026489] Switching to clocksource 32k_counter
[ 0.034332] AppArmor: AppArmor Filesystem Enabled
[ 0.043792] musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0
[ 0.048828] musb_hdrc musb_hdrc: USB OTG mode controller at fa0ab000 using
DMA, IRQ 92
[ 0.049072] NET: Registered protocol family 2
[ 0.049316] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.050231] TCP established hash table entries: 16384 (order: 5, 131072
bytes)
[ 0.050598] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.050842] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.050872] TCP reno registered
[ 0.050872] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.050933] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.051147] NET: Registered protocol family 1
[ 0.051971] PMU: registered new PMU device of type 0
[ 0.052062] NetWinder Floating Point Emulator V0.97 (double precision)
[ 0.052429] audit: initializing netlink socket (disabled)
[ 0.052520] type=2000 audit(0.234:1): initialized
[ 0.204467] Trying to unpack rootfs image as initramfs...
[ 6.792785] VFS: Disk quotas dquot_6.5.2
[ 6.793151] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 6.796142] fuse init (API version 7.14)
[ 6.796752] msgmni has been set to 969
[ 6.798339] Block layer SCSI generic (bsg) driver version 0.4 loaded (major
253)
[ 6.798400] io scheduler noop registered
[ 6.798400] io scheduler deadline registered
[ 6.798492] io scheduler cfq registered (default)
[ 6.854919] OMAP DSS rev 2.0
[ 6.855072] OMAP DISPC rev 3.0
[ 6.855133] OMAP VENC rev 2
[ 6.936004] Freeing initrd memory: 6608K
[ 7.019897] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 7.103820] serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654
[ 7.273925] serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654
[ 7.443908] serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654
[ 8.317108] console [ttyS2] enabled
[ 8.327575] brd: module loaded
[ 8.334167] loop: module loaded
[ 8.338897] omap2-nand driver initializing
[ 8.343353] NAND device: Manufacturer ID: 0x20, Chip ID: 0xba (ST Micro
omap2-nand.0)
[ 8.351287] NAND bus width 8 instead 16 bit
[ 8.355529] No NAND device found.
[ 8.359008] NAND device: Manufacturer ID: 0x20, Chip ID: 0xba (ST Micro NAND
256MiB 1,8V 16)
[ 8.367919] Creating 5 MTD partitions on "omap2-nand.0":
[ 8.373321] 0x000000000000-0x000000080000 : "X-Loader"
[ 8.379913] 0x000000080000-0x000000260000 : "U-Boot"
[ 8.386749] 0x000000260000-0x000000280000 : "U-Boot Env"
[ 8.393218] 0x000000280000-0x000000680000 : "Kernel"
[ 8.400665] 0x000000680000-0x000010000000 : "File System"
[ 8.496917] Fixed MDIO Bus: probed
[ 8.500640] PPP generic driver version 2.4.2
[ 8.505310] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256)
(6 bit encapsul.
[ 8.515075] CSLIP: code copyright 1989 Regents of the University of
California.
[ 8.522460] SLIP linefill/keepalive option.
[ 8.526916] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.533721] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
[ 8.539520] ehci-omap ehci-omap.0: new USB bus registered, assigned bus
number 1
[ 8.547119] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
[ 8.565704] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
[ 8.572265] hub 1-0:1.0: USB hub found
[ 8.576110] hub 1-0:1.0: 3 ports detected
[ 8.604827] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 8.611572] mice: PS/2 mouse device common for all mice
[ 8.617401] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
[ 8.624969] device-mapper: uevent: version 1.0.3
[ 8.630371] device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised:
[email protected]
[ 8.639221] device-mapper: multipath: version 1.1.1 loaded
[ 8.644805] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 8.652069] cpuidle: using governor ladder
[ 8.656188] cpuidle: using governor menu
[ 8.660278] sdhci: Secure Digital Host Controller Interface driver
[ 8.666503] sdhci: Copyright(c) Pierre Ossman
[ 8.859497] No device for DAI omap-mcbsp-dai-0
[ 8.864044] No device for DAI omap-mcbsp-dai-1
[ 8.868530] No device for DAI omap-mcbsp-dai-2
[ 8.873046] No device for DAI omap-mcbsp-dai-3
[ 8.877532] No device for DAI omap-mcbsp-dai-4
[ 8.882019] Not OMAP3 EVM!
[ 8.884765] OMAP3 Beagle/Devkit8000 SoC init
[ 8.889892] asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok
[ 8.898498] ALSA device list:
[ 8.901580] #0: omap3beagle (twl4030)
[ 8.905517] usb 1-2: new high speed USB device using ehci-omap and address 2
[ 8.913970] TCP cubic registered
[ 8.918365] NET: Registered protocol family 10
[ 8.924102] lo: Disabled Privacy Extensions
[ 8.929168] NET: Registered protocol family 17
[ 8.937744] Power Management for TI OMAP3.
[ 8.943908] VFP support v0.3: implementor 41 architecture 3 part 30 variant
c rev 3
[ 8.953338] registered taskstats version 1
[ 8.970397] omapfb omapfb: illegal display bpp
[ 8.974945] omapfb omapfb: failed to setup fb_info
[ 8.979888] omapfb omapfb: failed to setup omapfb
[ 8.984680] omapfb: probe of omapfb failed with error -22
[ 8.990692] regulator_init_complete: incomplete constraints, leaving VPLL2 on
[ 8.998138] regulator_init_complete: incomplete constraints, leaving VDAC on
[ 9.006134] twl_rtc twl_rtc: setting system clock to 2000-01-01 00:10:48 UTC
(946685448)
[ 9.014617] Freeing init memory: 240K
[ 9.075134] hub 1-2:1.0: USB hub found
[ 9.089294] hub 1-2:1.0: 5 ports detected
[ 9.156646] udev[67]: starting version 163
[ 9.183105] mmc0: host does not support reading read-only switch. assuming
write-enable.
[ 9.283294] mmc0: new high speed SDHC card at address aaaa
[ 9.378570] usb 1-2.1: new high speed USB device using ehci-omap and address
3
[ 9.489105] mmcblk0: mmc0:aaaa SU04G 3.69 GiB
[ 9.508056] mmcblk0: p1 p2
[ 10.669555] Btrfs loaded
[ 12.319122] mmcblk0: p1 p2
[ 18.701416] EXT3-fs: barriers not enabled
[ 32.599304] kjournald starting. Commit interval 5 seconds
[ 33.110748] EXT3-fs (mmcblk0p2): using internal journal
[ 33.116058] EXT3-fs (mmcblk0p2): recovery complete
[ 33.127777] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode
[ 61.024597] EXT3-fs: barriers not enabled
[ 61.029754] kjournald starting. Commit interval 5 seconds
[ 61.035400] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode
--------------------------------------------------
And then it freezes at this point.
Brett
--------------------------------------------------
--
BeagleBoard xM freezes while attempting to boot 10.10
https://bugs.launchpad.net/bugs/664827
You received this bug notification because you are a member of Ubuntu
Bugs, which is subscribed to Ubuntu.
--
ubuntu-bugs mailing list
[email protected]
https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
