I use a cheap $7 screwdriver set that I got from Harbor Freight. The telescoping handle along with the small bits are thin enough and long enough to get into the handle screws.
http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=93916 You do not need the extension, just the screwdriver. Great for working on laptops too. On Apr 25, 8:02 pm, "Matthew S. Carpenter" <[email protected]> wrote: > My 6 inch 15 torx sears craftsman model #47181 item #00947181000 is just > fine. You can buy it online at Sears.com. If you don't want to pay > shipping but can't find at your local Sears, ask for help. If they don't > have it, ask if they can order it from their warehouse for their next > load of freight. > > I have tried this screw driver on my 512ke, Plus, and SE. It will > probably work fine on the Classic too. > > <http://www.thecowsaysmoo.org/rockinkat/pictures/computers/mac/torx/be...> > <http://www.thecowsaysmoo.org/rockinkat/pictures/computers/mac/torx/pl...> > <http://www.thecowsaysmoo.org/rockinkat/pictures/computers/mac/torx/ha...> > <http://www.thecowsaysmoo.org/rockinkat/pictures/computers/mac/torx/ta...> > > <http://www.sears.com/shc/s/p_10153_12605_00947181000P?keyword=47181> > > -Matthew S. Carpenter > > > > d.colvin d.colvin wrote: > > You're right. 6 inches is not enough. I had measured a while back and > > i really think 9 or 10 inches of shaft is needed to really the get the > > job done. It depends on how big the handle is. > > > I used a long bolt that I found in my dad's barn/workshop. It's like a > > handyman's heaven. There are mountains of treasures out there. > > > On Sat, Apr 25, 2009 at 1:52 AM, Doug <[email protected] > > <mailto:[email protected]>> wrote: > > > The Torx is probably too short. What I did today was to buy about > > a 14 inch > > long tool with a screw in the end. I took my no. 15 Torx and > > pounded the > > handle off leaving a six inch piece. I then filed off the two > > tangs that > > held it into the plastic handle an Voila, it fit perfectly into > > the end with > > screws on. I tightened the screws and I had a Torx screwdriver > > about 20 > > inches long and the screws came out with no problems. The tool I > > bought at > > home Hardware cost me $9.99... > > > Doug > > > -----Original Message----- > > From: [email protected] > > <mailto:[email protected]> > > [mailto:[email protected] > > <mailto:[email protected]>] > > On Behalf Of Charles Lenington > > Sent: April 24, 2009 10:38 PM > > To: [email protected] > > <mailto:[email protected]> > > Cc: [email protected] <mailto:[email protected]> > > Subject: torx for compact Macs > > > Christian Wacker wrote: > > > I have a Mac Classic, who's hard disk has died recently. I have a > > > snip > > > Before I spend the small amount of money and time on my Classic, to > > > get a long enough torx driver to open the case, and the time even > > > opening it, > > I just happened to find a Tx-15 today. at a local tool store (Steve's > > wholesale Dist., Inc.) (www.steveswholesaletools.com > > <http://www.steveswholesaletools.com> ==== site appers to > > be down , I'll try to call around class to see why/etr) > > > It is 6" long made by > > Vermont American > > part #16093 > > sku 0 45325 16093 0 > > > cost $5.67 + tax > > > I do have 3 jpegs of the bit and package ask off list if you want the > > jpegs sent to you. > > > I have also been digging around in pawn shops and have found a few > > approx 2" long ones also. > > > I can take a picture of them also if needed for a guide in your hunt.- > > Hide quoted text - > > - Show quoted text - --~--~---------~--~----~------------~-------~--~----~ You received this message because you are subscribed to the Vintage Macs group. The list FAQ is at http://lowendmac.com/lists/vintagemacs.shtml and our netiquette guide is at http://www.lowendmac.com/lists/netiquette.shtml To post to this group, send email to [email protected] To unsubscribe from this group, send email to [email protected] For more options, visit this group at http://groups.google.com/group/vintage-macs?hl=en Low End Mac RSS feed at feed://lowendmac.com/feed.xml -~----------~----~----~----~------~----~------~--~---
