If you find out how to do that let me know how it's done as it would be a useful additional bit of knowledge! It's not something I think I can actually do on my Netgear router, but perhaps the D-link has more functionality.
-------------------------------------------- Peter Coulter -------------------------------------------- > -----Original Message----- > From: Tom Knowlton [mailto:[EMAIL PROTECTED] > Sent: Friday, March 26, 2004 11:10 PM > To: [EMAIL PROTECTED]; [EMAIL PROTECTED] > Subject: RE: router config to work with VNC > > > Network Admin says I need to change the DLink router settings > so it routes to itself. > > -----Original Message----- > From: Peter Coulter [mailto:[EMAIL PROTECTED] > Sent: Friday, March 26, 2004 4:01 PM > To: Tom Knowlton; [EMAIL PROTECTED] > Subject: RE: router config to work with VNC > > > The answer to that is yes ... plug the Actiontec not into the > WAN port of the D-link but into one of the LAN ports! :-) > Seems like a waste of good router though, but you are then > literally using it as a plain switch! > > -------------------------------------------- > Peter Coulter > -------------------------------------------- > > > > -----Original Message----- > > From: Tom Knowlton [mailto:[EMAIL PROTECTED] > > Sent: Friday, March 26, 2004 10:49 PM > > To: [EMAIL PROTECTED]; [EMAIL PROTECTED] > > Subject: RE: router config to work with VNC > > > > > > Isn't there anyway to sort of turn the DLink router into > > something that behaves more like a hub or a switch?????? > > > > > > Tom > > > > -----Original Message----- > > From: Peter Coulter [mailto:[EMAIL PROTECTED] > > Sent: Friday, March 26, 2004 3:39 PM > > To: Tom Knowlton; [EMAIL PROTECTED] > > Subject: RE: router config to work with VNC > > > > > > Tom: > > > > The ActionTec 1524R SU is a wireless broadband gateway > > (modem/router). The Dlink 614+ is a wireless router. This > > begs the quesiton why you need the D-link router at all? > > Unless there is some other reason you haven't mentioned that > > you need the D-link for? > > > > To connect to the internet via a DSL connection, and have a > > home LAN sharing that connection, is fully within the scope > > of the ActionTec alone (more than enough connectivity with 4 > > x LAN ports PLUS wireless). > > In fact adding the D-link into the mix is just adding to your > > configuration difficulties (connecting two NAT routers > > back-to-back, each DHCP servers, each with wireless!!). For a > > start you've having to set up port-forwarding in two places > > when it really isn't necessary. > > > > I suggest using the ActionTec alone and see if you can get > > GoToMyVNC.com to see Display 0 .. 9. > > > > -------------------------------------------- > > Peter Coulter > > -------------------------------------------- > > > > > > > -----Original Message----- > > > From: Tom Knowlton [mailto:[EMAIL PROTECTED] > > > Sent: Friday, March 26, 2004 8:43 PM > > > To: [EMAIL PROTECTED]; [EMAIL PROTECTED] > > > Subject: RE: router config to work with VNC > > > > > > > > > Peter: > > > > > > I'm grateful for your help. > > > > > > A little more on the modem and router: > > > > > > Both have 4 ethernet ports. DLink Router has a WAN port, > which the > > > ActionTec is plugging into right now (using one of the ethernet > > > ports on the ActionTec). > > > > > > The ActionTec is a model 1524R SU. It is a Wireless-ready (not > > > being utilized by me) DSL broadband modem. > > > > > > ActionTec Vendor Home Page: > > > http://www.actiontec.com/ > > > > > > ActionTec Model specific: > > > http://www.actiontec.com/products/broadband/wireless_ready_dsl > > > _gateway/wireless_ready_dsl_gateway_specifications.html > > > > > > > > > ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ > > > > > > DLink Wireless Router is a DI 614+. I need the DLink so I can > > > transmit the Internet to our laptop, and daughter's computer > > > upstairs. > > > > > > DLink router Vendor Home Page: > > > http://www.dlink.com/ > > > > > > > > > DLink router Model specific: http://www.dlink.com/products/?pid=20 > > > > > > > > > > > > > > > ============================================= > > > ============================================= > > > > > > To answer your other questions (best I can): > > > > > > Q: Is the modem a DHCP server? > > > A: Yes. I turned this OFF once with disasterous consequences. > > > > > > In fact, I think DHCP is turned on for both the ActionTec > modem and > > > the DLink router. I think it is Dynamic DHCP assigned for both > > > modem and router. > > > > > > > > > IMPORTANT UPDATE on the DLink (LAN) subnet: > > > > > > I have changed the DLink router subnet over to 10.x.x.x. > I did this > > > last night. > > > > > > > > > Q: I assume also that it is set to automatically acquire Default > > > Gateway and DNS server information from the ISP > > > > > > A: Not sure. Seems right. > > > > > > > > > > > > <<<<<Looking forward to actually getting to the VNC bit!! ;-)>>>>> > > > > > > Me too! > > > > > > > > > Right before I went to bed last night I ran the GoToMyVNC.com > > > against my IP address (205.208.x.x) and Display 0 thru 9 were NOT > > > OPEN. :( > > > > > > > > > > > > Thanks, > > > > > > > > > Tom > > > > > > > > > > > > > > > > > > -----Original Message----- > > > From: Peter Coulter [mailto:[EMAIL PROTECTED] > > > Sent: Friday, March 26, 2004 1:21 PM > > > To: Tom Knowlton; [EMAIL PROTECTED] > > > Subject: RE: router config to work with VNC > > > > > > > > > Tom, > > > > > > You'd need to say a bit more about the ActionTec modem before I > > > could answer questions on it. Even the model name would allow a > > > manual to be dragged up online. But your modem must be slightly > > > different to mine because if I type my external > > > (dynamic) IP address into IE it doesn't take me to the modem; > > > the only way I can access the modem via IE is using 192.168.0.1. > > > > > > Also, when it comes to mind: Is the modem a DHCP server? > The D-link > > > router will be a DHCP server by default and you cannot > have two DHCP > > > servers on the same subnet or they will likely be issuing > clashing > > > IP addresses. So if both devices are DHCP servers the > facility would > > > have to be disabled in one or other of them. To me it makes more > > > sense to have the router as the DHCP sever and thus > deactivate the > > > facility in the modem (if such a facility exists there). > > > > > > It's rarely enough just to quote an IP address; usually > at least the > > > sub-net mask but also the default gateway are necessary > to get the > > > whole picture (although in most small/home LANs the former can be > > > guessed with almost complete certainty and the latter with a fair > > > degree of > > > certainty!) So when you say that you have moved the D-link > > > over to the IP address 192.168.0.2 I assume you mean you've > > > set the router IP address in the LAN-side set-up pages. I > > > assume also that it is set to automatically acquire Default > > > Gateway and DNS server information from the ISP; that will be > > > how the D-link directs traffic that is not bound for its own > > > sub-net out onto the Internet, I don't think it really cares > > > too much about the fact it is going through the modem, it > > > just dumps stuff out the default gateway as its only known > > > route to the outside world. > > > > > > I must say there are things that get me excited ... but routers > > > ain't one of 'em! :-) Looking forward to actually getting > to the VNC > > > bit!! ;-) > > > > > > Peter > > > > > > > > > > -----Original Message----- > > > > From: Tom Knowlton [mailto:[EMAIL PROTECTED] > > > > Sent: 26 March 2004 03:54 > > > > To: coulter; [EMAIL PROTECTED] > > > > Subject: RE: router config to work with VNC > > > > > > > > > > > > UPDATE: > > > > > > > > I moved my DLink router IP over to 192.168.0.2 > > > > > > > > Now when I type 192.168.0.2 it takes me to the DLink Router > > > config (as > > > > expected) > > > > > > > > When I type in my static IP address (205.208.XXX.XXX) it > > takes me to > > > > my ActionTec broadband modem config....is that right? > > > > > > > > Now, there is still another IP address, isn't there? The > > > one that my > > > > DLink is using to connect to my ActionTec modem. > > > > That is the part I am not sure about. > > > > > > > > So I need an answer to that part, plus I still need to get VNC > > > > working. > > > > > > > > But the good news is that for the FIRST TIME....I can get to the > > > > firewall config for both my DLink Router and my ActionTec > > broadband > > > > modem WITHOUT having to disconnect any cables. I'm so excited. > > > > > > > > -----Original Message----- > > > > From: coulter [mailto:[EMAIL PROTECTED] > > > > Sent: Thursday, March 25, 2004 6:36 AM > > > > To: [EMAIL PROTECTED] > > > > Cc: Tom Knowlton > > > > Subject: RE: router config to work with VNC > > > > > > > > > > > > As noted by other posters your diagram is incomplete. > > > > > > > > However what if does tell me is that you have two devices - > > > namely the > > > > Actiontec modem and the D-link router - with the same > IP address > > > > namely 192.168.0.1 (you say it in words in some of the > > > supporting text > > > > but it is not shown in the diagrams). > > > > > > > > First you can't have two devices with the same IP > address and not > > > > expect problems. Plus your Dlink must be getting very > > > confused -- it's > > > > supposed to be a router, by definition a router routes! Usually > > > > between different sub-nets!! :-) But as it is seeing > the same IP > > > > address 192.168.0.1 on each of its port (both WAN-side and > > > > LAN-side) it's likely not a happy bunny. > > > > > > > > For me the easiest way to solve this is to put the modem and the > > > > router on different sub-nets as follows: leave the modem on > > > > 192.168.0.1 (the 192.168.0.0/255.255.255.0 sub-net) and put > > > the router > > > > on a completely different sub-net. So that it is very > > clear which is > > > > which make them very different, thus I suggest putting > > the router on > > > > the 10.0.0.0 / 255.255.255.0 (although really anything > other than > > > > 192.168.0.x will do). The router being the DHCP server > > then dishes > > > > out LAN IP address to this revised sub-net. The very first > > > > consequence of this will be that you can access both > > devices via IE > > > > using their now different IP addresses without having to be > > > > disconnect the devices every now and again! ;-) > > > > > > > > Once you get this difficulty between modem and router > > sorted you may > > > > be able to progress with VNC issues. Set up > > port-forwarding on each > > > > device now as appropriate. > > > > > > > > Good luck, > > > > P > > > > > > > > > --__--__-- > > > > > > > > > > Message: 14 > > > > > Subject: RE: router config to work with VNC > > > > > Date: Wed, 24 Mar 2004 17:13:21 -0700 > > > > > From: "Tom Knowlton" <[EMAIL PROTECTED]> > > > > > To: "Scott C. Best" <[EMAIL PROTECTED]>, <[EMAIL PROTECTED]> > > > > > > > > > > Does this diagram help any? (until I can get Kaboodle up > > > > and running) > > > > > > > > > > > > > > > http://www.knowltonfamily.com/config_port_forward.gif _______________________________________________ VNC-List mailing list [EMAIL PROTECTED] To remove yourself from the list visit: http://www.realvnc.com/mailman/listinfo/vnc-list
