Hi Fred:

Here's my page on transmission line Zo and how it's not a constant impedance:
http://www.prc68.com/I/Zo.shtml
I've added a list of impedance equipment on the Impedance web page:
http://www.prc68.com/I/Z.shtml#Rel

I've used a number of the Keithley DC boxes for automated testing of 
semiconductors.
http://www.prc68.com/I/RASS_PP.html#D
http://www.prc68.com/I/RASS_PP.html#TD
They are great where you need a current source in the nano or femto amp range 
or higher.

Have Fun,

Brooke Clarke
http://www.PRC68.com
http://www.end2partygovernment.com/Clarke4Congress.html


Fred Schneider wrote:
Thanks for the info, the HP impedance measurement handbook is a bit my bible so 
I know it.

About analysers, i know a modern impedance analyser, be it a vna, IV, or just a 
LCR meter can be more accurate and has more possibilities.
I have two digital vna's  ( DG8SAQ VNWA) one that has the RF-IV test head 
designed by Paul and an analog one from HP. The latter I yesterday used to make 
RF-IV measurements as an experiment. A tek CT currentprobe from splitter to 
reference and the other output via a shunt fixture to the test port. The result 
was above wat I expected,  a nice impedance curve that has a resolution of 40 
dB under 1 ohm.
I am most time busy doing network analysing, component research, most of them 
involve capacitors and parasitic behaviour of components. And playing with 
calibrators.

But I teached my self everything and i have no math education so I always 
avoided that ( i have discalculus too) but I like it a lot and the lat time I 
try to get back to the basics for deeper understanding about what I am 
meaduring and for most practice and learn some math. The result is new ( that 
is for me) ways to measure things. I ( re ?)invented a CF converter, build snd 
designed a IV-meter like fF meter, did coulomb and C ( under 10pF) measurements 
with a O plugin in an old Tek 547 ( after that i found out it was, in a 
different form, described in the manual). Did tek-130 style C measements like 
described by Terman. Measured capacitanceusing DC, tryed about 10 ways to 
measure ESR, recently tried to measure the parasitics of 10 m bare wire. Things 
like inductance, resistance, skineffect, Q, capacitance ect. Very intresting, 
the meaurements worked, grapical it made sense and gave an idea, but the math 
was to complex for me to extract it to numbers, gave the data ( thoug!
  hstone files) and graphs to a friend who is a math , RF engineer and RF guru 
but he had to admit it was even to complex for him. He could probably do it but 
it would take to much time. I could not anlyse the data my self.  This is pure 
hobby, I do not even have an electronic education.

I have a marconi TF1313A, 0,1% bridge and a HP ( the same, like the damaged one 
you have)
I builded a simpke complex measurement bridge based on the arrl antenna 
handbook. Also made a poor mans wobbulator based on a noise source, external 
signal generator and audio SA software ( involved mixing so it could be used 
for the whole HF band)

But it would be great to have an old bridge like the GR ones. With lots of 
knobs and after that calculate from there, to the corrections ect. Mostly to 
measure capacitove stuff.

I'm offered a GR1620 from a list member that I will buy, i read the manual and 
I allready love it.
With the info gathered I also would like to have a passive RF type bridge. I 
know I can easy use a vna but I like to measure the basics and try to extract 
the other parametrs from there as a learning experience. I am now doing some 3 
voltmeter experiments. It is nice to compare results from this experiments to 
my vna. Some times I'm way of but it feels good if it worked out well. Like 
meauring capacitance and esr on a curvtracer, that was fun. Or the RI-IV 
meaurement of a cap. After that I had calculated esr capacitance and esl from 
that I did a simulation and that gave the same SRF. That gives me a kick.

So to be short ( very difficult for me ;-) ) , i do not have a need for a 
frequency or so, i adjust/ make up my experiments around an instrument.

Thanks to the answers from you and the others and your link i now know were to 
look for and use the right search terms. First wait for answer from the seller 
of the GR about transport and hopr we find a way abd then play with that nice 
instrument and then look for a RF admitance/impedance bridge.

Short question, keithley makes source meters, They are in the micromeasurements 
handbook but I can not really place this. It sounds like a sort of IV meter, or 
coulomb meter but for DC. Not planning to buy one, just curious.

Thanks,

Fred PA4TIM

Op 25 mei 2012 om 22:41 heeft Brooke Clarke<[email protected]>  het volgende 
geschreven:

Hi Fred:

In HP speak "meters" have numerical readouts and "analyzers" have graphical 
readouts.
So the 4-terminal pair LCR meters are good, but the 4-terminal pair LCR 
analyzers are better.
You can substitute "Impedance" for LCR in the above.
I say better because the you can get an equivalent circuit from an analyzer 
that has more than two components, which is the limit of the meters.
Some analyzers can fit complex models automatically, for example Impedance 
Analyzers and Crystal Impedance meters (which use swept frequency but only have 
numerical readouts).

The bible for impedance measurement is HP's "The Impedance Measurement 
Handbook", see my Related paragraph on the Impedance web page:
http://www.prc68.com/I/Z.shtml#Rel
This is a MUST READ if you're into precision LCR type measurements.
There's also the issue of compensation and correction of fixture parasitics.  
For more on fixtures see the HP Accessories Selection Guide for Impedance 
Measurements.

The key idea is that there's a contour plot of accuracy vs impedance and 
frequency for the different measurement methods, with the 4-terminal pair 
method giving the most accurate results.  
http://www.prc68.com/I/HP4274_4275_LCR.shtml#4TP
A lot of that is because of canceling magnetic coupling between the 4 coax 
cables (note that not all the coax shields are are at ground).
The earlier instruments that used 4 each 5-way binding posts are not anywhere 
as accurate.

Have Fun,

Brooke Clarke
http://www.PRC68.com
http://www.end2partygovernment.com/Clarke4Congress.html


Fred Schneider wrote:
Hi,
I do not know if it is a topic for here, but it is about precision messurements.
For my collection and learing through measuring the old , "back to the basics" way,  I am 
looking for a bridge to measure things like small caps, dielectric constants ad other 
"weard" parameters. I have several VNA's and RLC bridges but they used to make bridges 
that you can see as a manual VNA. It gave R and jX, sometimes with build in detector and 
oscillator, sometimes using these external.
But there are so many bridges, from general purpose to special measuring things 
( like the resistance from a detonator) and from general purpose to high 
precision that I am lost. I think GR or Wayne Kerr made the best ones. I'm to 
young to have experience with them and never seen one for real.

Can someone give me a hint what to search for. For instance the right name of 
such a bridge ( i think Z/Y or admittance cq impedance bridge) and what is 
important so I can determ if they are for what I want and not just a allround 
LCR bridge.

I want to measure the more extreme things like ESR, fF, delectric 
proporties/losses ect but for most I love old precision measurement instruments 
which make you think about what you do and have lots of knobs instead of menus.

Fred PA4TIM
_______________________________________________
volt-nuts mailing list -- [email protected]
To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/volt-nuts
and follow the instructions there.


_______________________________________________
volt-nuts mailing list -- [email protected]
To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/volt-nuts
and follow the instructions there.
_______________________________________________
volt-nuts mailing list -- [email protected]
To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/volt-nuts
and follow the instructions there.




_______________________________________________
volt-nuts mailing list -- [email protected]
To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/volt-nuts
and follow the instructions there.

Reply via email to