There is another issue too, where a messages is sent without yearly rain as
this one, where the daily rainin is used by intercetor. It should not mix
the yearly and daily measurements it should use only one of them which
exists in all messages. But when it uses the daily it zeros the total rail
so it will add next 2.25 or 2.48 as rain for the day. I think the statition
still send messages what it shouldn't be.
May 22 07:40:34 UBUNTUMATE-1000H weewx[26366]: interceptor: ServerThread:
GET:
siteid=xxxx&siteAuthenticationKey=xxxx&dateutc=2019-05-21%2021:40:33&tempf=54.3&dewptf=47.7&humidity=78&baromin=30.34&winddir=34&windspeedmph=5.4&windgustmph=6.9&rainin=0.00&
*dailyrainin=0.00*&softwaretype=EasyWeatherV1.3.2
May 22 07:40:34 UBUNTUMATE-1000H weewx[26366]: interceptor: MainThread: raw
data:
siteid=xxxx&siteAuthenticationKey=xxxx&dateutc=2019-05-21%2021:40:33&tempf=54.3&dewptf=47.7&humidity=78&baromin=30.34&winddir=34&windspeedmph=5.4&windgustmph=6.9&rainin=0.00&
*dailyrainin=0.00*&softwaretype=EasyWeatherV1.3.2
May 22 07:40:34 UBUNTUMATE-1000H weewx[26366]: interceptor: MainThread:
using rain_total 0.0 from dailyrainin
May 22 07:40:34 UBUNTUMATE-1000H weewx[26366]: interceptor: MainThread:
firmware EasyWeatherV1.3.2: baromin is barometer
May 22 07:40:34 UBUNTUMATE-1000H weewx[26366]: interceptor: MainThread:
unrecognized parameter rainin=0.00
May 22 07:40:34 UBUNTUMATE-1000H weewx[26366]: interceptor: MainThread:
ignored parameter softwaretype=EasyWeatherV1.3.2
May 22 07:40:34 UBUNTUMATE-1000H weewx[26366]: interceptor: MainThread:
unrecognized parameter siteid=xxxx
May 22 07:40:34 UBUNTUMATE-1000H weewx[26366]: interceptor: MainThread:
unrecognized parameter siteAuthenticationKey=xxxx
May 22 07:40:34 UBUNTUMATE-1000H weewx[26366]: interceptor: MainThread:
rain counter wraparound detected: *new=0.0* last=2.25
Gábor
Joe Santas <joesan...@gmail.com> ezt írta (időpont: 2019. máj. 22., Sze
8:10):
> Just tried disabling rapid fire but no change. Its still incrementing as
> previously... That 2.2.x figure still pops up.. Not sure where its pulling
> this from
> using rain_total 2.248
>
>
> May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread:
> ignored parameter action=updateraw
> May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread:
> unrecognized parameter weeklyrainin=0.00
> May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread: raw
> packet: {'wind_speed': 2.7, 'humidity_in': 54.0, 'temperature_in': 72.7,
> 'barometer': 30.3, 'windchill': 70.9, 'dewpoint': 45.5, 'humidity_out':
> 40.0, 'uv': 0.0, 'radiation': 50.65, 'rain': 0.0, 'dateTime': 1558505079,
> 'temperature_out': 70.9, 'wind_dir': 17.0, 'rain_total': 2.25, 'usUnits':
> 1, 'wind_gust': 3.4}
> May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread:
> mapped packet: {'barometer': 30.3, 'windchill': 70.9, 'dewpoint': 45.5,
> 'outHumidity': 40.0, 'UV': 0.0, 'radiation': 50.65, 'rain': 0.0,
> 'dateTime': 1558505079, 'windDir': 17.0, 'outTemp': 70.9, 'windSpeed': 2.7,
> 'inHumidity': 54.0, 'inTemp': 72.7, 'windGust': 3.4, 'usUnits': 1}
> May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: ServerThread:
> POST:
> PASSKEY=XXXX&stationtype=EasyWeatherV1.3.2&dateutc=2019-05-22+06:04:39&tempinf=72.7&humidityin=54&baromrelin=30.30&baromabsin=29.69&tempf=70.9&humidity=40&winddir=17&windspeedmph=2.7&windspdmph_avg10m=0.0&windgustmph=3.4&maxdailygust=6.9&rainratein=0.000&eventrainin=0.000&hourlyrainin=0.000&dailyrainin=0.000&weeklyrainin=0.000&monthlyrainin=
> 1.346&yearlyrainin=2.248&solarradiation=50.65&uv=0
> May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread: raw
> data:
> PASSKEY=B49D741DD8D21E1D5B657ADE7C3A9D91&stationtype=EasyWeatherV1.3.2&dateutc=2019-05-22+06:04:39&tempinf=72.7&humidityin=54&baromrelin=30.30&baromabsin=29.69&tempf=70.9&humidity=40&winddir=17&windspeedmph=2.7&windspdmph_avg10m=0.0&windgustmph=3.4&maxdailygust=6.9&rainratein=0.000&eventrainin=0.000&hourlyrainin=0.000&dailyrainin=0.000&weeklyrainin=0.000&monthlyrainin=
> 1.346&yearlyrainin=2.248&solarradiation=50.65&uv=0
> May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread:
> using rain_total 2.248 from yearlyrainin
> May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread:
> unrecognized parameter eventrainin=0.000
> May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread:
> unrecognized parameter baromrelin=30.30
> May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread:
> unrecognized parameter maxdailygust=6.9
> May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread:
> unrecognized parameter monthlyrainin=1.346
> May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread:
> unrecognized parameter PASSKEY=
> May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread:
> unrecognized parameter humidityin=54
> May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread:
> unrecognized parameter rainratein=0.000
> May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread:
> unrecognized parameter windspdmph_avg10m=0.0
> May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread:
> unrecognized parameter hourlyrainin=0.000
> May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread:
> unrecognized parameter baromabsin=29.69
> May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread:
> unrecognized parameter tempinf=72.7
> May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread:
> unrecognized parameter uv=0
> May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread:
> unrecognized parameter stationtype=EasyWeatherV1.3.2
> May 22 16:04:39 UBUNTUMATE-1000H weewx[2069]: interceptor: MainThread:
> unrecognized parameter weeklyrainin=0.000
>
>
> On Wednesday, May 22, 2019 at 2:46:57 PM UTC+10, gjr80 wrote:
>>
>> Hi,
>>
>> Not an interceptor or ECOWITT HP2551 user but looking at your log1.txt
>> log extract it appears that your station is sending both rapidfire as well
>> as normal (non-rapidfire) updates.
>>
>> Rapid fire:
>> May 22 07:40:02 UBUNTUMATE-1000H weewx[26366]: interceptor: ServerThread:
>> GET: ID=IVICTORI1768&PASSWORD=XXXX&indoortempf=71.1&tempf=54.3&dewptf=
>> 47.7&windchillf=54.3&indoorhumidity=52&humidity=78&windspeedmph=6.9&
>> windgustmph=8.1&winddir=40&absbaromin=29.73&baromin=30.34&rainin=0.00&
>> dailyrainin=0.00&weeklyrainin=0.00&monthlyrainin=1.35&yearlyrainin=2.25&
>> solarradiation=16.88&UV=0&dateutc=2019-05-21%2021:40:01&softwaretype=
>> EasyWeatherV1.3.2&action=updateraw&realtime=1&rtfreq=5
>>
>> normal:
>> May 22 07:40:18 UBUNTUMATE-1000H weewx[26366]: interceptor: ServerThread:
>> POST: PASSKEY=XXXX&stationtype=EasyWeatherV1.3.2&dateutc=2019-05-21+21:40
>> :17&tempinf=71.4&humidityin=52&baromrelin=30.34&baromabsin=29.73&tempf=
>> 54.3&humidity=78&winddir=18&windspeedmph=5.4&windspdmph_avg10m=0.0&
>> windgustmph=6.9&maxdailygust=15.9&rainratein=0.000&eventrainin=0.000&
>> hourlyrainin=0.000&dailyrainin=0.000&weeklyrainin=0.000&monthlyrainin=
>> 1.346&yearlyrainin=2.248&solarradiation=16.02&uv=0
>>
>> This really shouldn't be an issue but if you have a look at the number of
>> decimal places used for each rain related observation in each you will see
>> the RF updates use 2 decimal places and the normal updates 3 decimal
>> places. Consequently, when you have normal after a RF you get a rain
>> counter wraparound detected and your rainfall has the wrapped around figure
>> added. If you have RF after normal you get 0.002 inches added. RF after RF
>> has no effect as both yearly rain fields are identical. I don't think using
>> any of the other rain fields will make a difference because the same
>> decimal places difference exist with both.
>>
>> Maybe less than ideal but can you turn off RF updates on your station,
>> that would at last show if that cures the issue or not. If so, maybe the
>> solution is to get the interceptor driver to ignore either the RF updates
>> or the normal updates. Not sure whether it can or not, probably one for
>> Matthew the author.
>>
>> Gary
>>
>> On Wednesday, 22 May 2019 14:13:03 UTC+10, Joe Santas wrote:
>>>
>>> Cleared the settings on the weatherstation. Same issue again.
>>> Obviously something else is going on. Also tried shutting down the weather
>>> station and deleting the weewx.sdb file so it re creates a new one but no
>>> joy so far.
>>> I have attached the latest copy of the log.
>>>
>>> Regards
>>>
>>>
>>>
>>> On Wednesday, May 22, 2019 at 2:22:50 AM UTC+10, Gábor Szabados wrote:
>>>>
>>>> Sounds like a plan. Let me know once you have done it.
>>>>
>>>> Interceptor should receive only the wu messages, then it should not
>>>> have any issue.
>>>>
>>>> Gabor
>>>>
>>>> Joe Santas <joes...@gmail.com> ezt írta (időpont: 2019. máj. 21., Ke
>>>> 17:41):
>>>>
>>>>> From what i have read they specify just the tcp to port 80 which i
>>>>> already have in place. What i will do is deactivate the upload features
>>>>> in
>>>>> the weatherstation its self and see if it makes a difference and leave the
>>>>> rules i currently have in place and see if this sorts it.
>>>>> Once this is done i will configure weewx config file to push the data
>>>>> up to wunderground and weathercloud any any other services i use.
>>>>>
>>>>> Regards
>>>>>
>>>>> On Wednesday, May 22, 2019 at 1:35:11 AM UTC+10, Gábor Szabados wrote:
>>>>>>
>>>>>> Read about how you can redirect only the traffic to WU servers to
>>>>>> your weewx server then you will be ok.
>>>>>>
>>>>>> I've seen some Merlin router firmware descriptions how it can be
>>>>>> done. Or DD-WRT descriptions are around the net too.
>>>>>>
>>>>>> Gabor
>>>>>>
>>>>>> Joe Santas <joes...@gmail.com> ezt írta (időpont: 2019. máj. 21., Ke
>>>>>> 16:22):
>>>>>>
>>>>>>> You may be onto something. So i will have to turn off the non wu
>>>>>>> servers on the device its self. Im unable to do this as i am at work
>>>>>>> but i
>>>>>>> can reconfigure my router remotely to route the correct traffic. I can
>>>>>>> try
>>>>>>> this from work. Which protocol should i leave active? At the moment i
>>>>>>> am
>>>>>>> forwarding all tcp traffic to my weewx server from the weather station.
>>>>>>>
>>>>>>> Regards
>>>>>>>
>>>>>>> On Wednesday, May 22, 2019 at 12:13:36 AM UTC+10, Gábor Szabados
>>>>>>> wrote:
>>>>>>>>
>>>>>>>> I can see more issues there, because I faced a similar one before.
>>>>>>>>
>>>>>>>> One of your issues, maybe the main one, that your weather station
>>>>>>>> is sending reports to multiple servers and all of them ia redirected to
>>>>>>>> your weewx. Interceptor tries to parse all the messages and faces a
>>>>>>>> mixed
>>>>>>>> state with yearlyrainin and dailyrainin and some rounding issues.
>>>>>>>>
>>>>>>>> First try to turn off the reporting to the non-wu servers. Or set
>>>>>>>> your router to forward only the wu request to your weewx. Then the
>>>>>>>> interceptor will recieve and parse only one kind of messages.
>>>>>>>>
>>>>>>>> Gabor
>>>>>>>>
>>>>>>>> Joe Santas <joes...@gmail.com> ezt írta (időpont: 2019. máj. 21.,
>>>>>>>> Ke 15:52):
>>>>>>>>
>>>>>>>>> wraparound detected in this log.
>>>>>>>>> After clearing the database rainfall graph has started to populate
>>>>>>>>> once again even though no rain lol.
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>> On Tuesday, May 21, 2019 at 5:12:03 PM UTC+10, Gábor Szabados
>>>>>>>>> wrote:
>>>>>>>>>>
>>>>>>>>>> Hi Joe,
>>>>>>>>>>
>>>>>>>>>> Could you try to look for messages in the log, like interceptor:
>>>>>>>>>> MainThread: rain counter wraparound detected:
>>>>>>>>>>
>>>>>>>>>> I can see a rounding issue (maybe) at the yearly rain is once
>>>>>>>>>> 2.248 the then 2.25, when no weekly rain change.
>>>>>>>>>>
>>>>>>>>>> May 21 02:53:17 UBUNTUMATE-1000H weewx[7192]: interceptor:
>>>>>>>>>> MainThread: raw data:
>>>>>>>>>> PASSKEY=********************&stationtype=EasyWeatherV1.3.2&dateutc=2019-05-20+16:53:05&tempinf=65.8&humidityin=60&baromrelin=30.14&baromabsin=29.54&tempf=55.4&humidity=77&winddir=16&windspeedmph=2.9&windspdmph_avg10m=0.0&windgustmph=3.4&maxdailygust=8.1&rainratein=0.000&eventrainin=0.000&hourlyrainin=0.000&dailyrainin=0.000&weeklyrainin=0.000&monthlyrainin=1.346&yearlyrainin=2.248&solarradiation=0.00&uv=0
>>>>>>>>>>
>>>>>>>>>> May 21 02:53:22 UBUNTUMATE-1000H weewx[7192]: interceptor:
>>>>>>>>>> ServerThread: GET:
>>>>>>>>>> ID=*********&PASSWORD=****&indoortempf=65.8&tempf=55.4&dewptf=48.4&windchillf=55.4&indoorhumidity=60&humidity=77&windspeedmph=2.9&windgustmph=3.4&winddir=16&absbaromin=29.54&baromin=30.14&rainin=0.00&dailyrainin=0.00&weeklyrainin=0.00&monthlyrainin=1.35&yearlyrainin=2.25&solarradiation=0.00&UV=0&dateutc=2019-05-20%2016:53:21&softwaretype=EasyWeatherV1.3.2&action=updateraw&realtime=1&rtfreq=5
>>>>>>>>>>
>>>>>>>>>> Look for wraparound events and check on your console too what is
>>>>>>>>>> your yearly value. Try to find places where the yearlyrainin changes
>>>>>>>>>> and
>>>>>>>>>> where it calculates rain from the change then I can try to find you
>>>>>>>>>> the
>>>>>>>>>> logic what goes wrong. Look for dateutc values too, is it
>>>>>>>>>> incremental or
>>>>>>>>>> changes back time to time when wraparound happens, if happens.
>>>>>>>>>>
>>>>>>>>>> Best Regards,
>>>>>>>>>>
>>>>>>>>>> Gabor
>>>>>>>>>>
>>>>>>>>>> --
>>>>>>>>> You received this message because you are subscribed to the Google
>>>>>>>>> Groups "weewx-user" group.
>>>>>>>>> To unsubscribe from this group and stop receiving emails from it,
>>>>>>>>> send an email to weewx...@googlegroups.com.
>>>>>>>>> To view this discussion on the web visit
>>>>>>>>> https://groups.google.com/d/msgid/weewx-user/f4434e12-7ed4-4a60-bc6c-42ff8de0d5ee%40googlegroups.com
>>>>>>>>> <https://groups.google.com/d/msgid/weewx-user/f4434e12-7ed4-4a60-bc6c-42ff8de0d5ee%40googlegroups.com?utm_medium=email&utm_source=footer>
>>>>>>>>> .
>>>>>>>>> For more options, visit https://groups.google.com/d/optout.
>>>>>>>>>
>>>>>>>> --
>>>>>>> You received this message because you are subscribed to a topic in
>>>>>>> the Google Groups "weewx-user" group.
>>>>>>> To unsubscribe from this topic, visit
>>>>>>> https://groups.google.com/d/topic/weewx-user/lg4W_4qHTaQ/unsubscribe
>>>>>>> .
>>>>>>> To unsubscribe from this group and all its topics, send an email to
>>>>>>> weewx...@googlegroups.com.
>>>>>>> To view this discussion on the web visit
>>>>>>> https://groups.google.com/d/msgid/weewx-user/30272d74-fedd-46a6-9a0f-ba66112df697%40googlegroups.com
>>>>>>> <https://groups.google.com/d/msgid/weewx-user/30272d74-fedd-46a6-9a0f-ba66112df697%40googlegroups.com?utm_medium=email&utm_source=footer>
>>>>>>> .
>>>>>>> For more options, visit https://groups.google.com/d/optout.
>>>>>>>
>>>>>> --
>>>>> You received this message because you are subscribed to the Google
>>>>> Groups "weewx-user" group.
>>>>> To unsubscribe from this group and stop receiving emails from it, send
>>>>> an email to weewx...@googlegroups.com.
>>>>> To view this discussion on the web visit
>>>>> https://groups.google.com/d/msgid/weewx-user/a5b531bf-8bd0-4ede-8ae4-6d5d84f34a3a%40googlegroups.com
>>>>> <https://groups.google.com/d/msgid/weewx-user/a5b531bf-8bd0-4ede-8ae4-6d5d84f34a3a%40googlegroups.com?utm_medium=email&utm_source=footer>
>>>>> .
>>>>> For more options, visit https://groups.google.com/d/optout.
>>>>>
>>>> --
> You received this message because you are subscribed to the Google Groups
> "weewx-user" group.
> To unsubscribe from this group and stop receiving emails from it, send an
> email to weewx-user+unsubscr...@googlegroups.com.
> To view this discussion on the web visit
> https://groups.google.com/d/msgid/weewx-user/e44bf030-458a-45c4-8a98-0a52af19cb5d%40googlegroups.com
> <https://groups.google.com/d/msgid/weewx-user/e44bf030-458a-45c4-8a98-0a52af19cb5d%40googlegroups.com?utm_medium=email&utm_source=footer>
> .
> For more options, visit https://groups.google.com/d/optout.
>
--
You received this message because you are subscribed to the Google Groups
"weewx-user" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to weewx-user+unsubscr...@googlegroups.com.
To view this discussion on the web visit
https://groups.google.com/d/msgid/weewx-user/CAEx3znJ9%2B0PtN1e_J%3D8SonkGO-OYOjQv85H%3DS295YW3u8tHSbw%40mail.gmail.com.
For more options, visit https://groups.google.com/d/optout.
