Weewx version 4.9.1 working fine with my Vantage Vue. All log output looks no different to version 4.8.0. Console firmware is up to date, the console is connected to my Raspberry Pi3B+ using the standard Davis USB console logger. Pleased with Weewx and the flexibility it can offer. Regards Phil
On Thursday, October 27, 2022 at 6:25:47 PM UTC+1 gjce...@gmail.com wrote: > The Vantage Vue console with Firmware 3.0 is working just fine with weewx > 4.9.1 and the new vantage driver. > > On Thursday, October 27, 2022 at 3:18:14 AM UTC-7 Gerard Cerchio wrote: > >> My Vantage Vue is 4 years later, any thoughts if it would run into the >> same problem? >> >> cserve:/etc/weewx# wee_device --info >> Using configuration file /etc/weewx/weewx.conf >> Using Vantage driver version 3.2.3 (weewx.drivers.vantage) >> Querying... >> Davis Vantage EEPROM settings: >> >> CONSOLE TYPE: Vantage Vue >> >> CONSOLE FIRMWARE: >> Date: May 1 2012 >> Version: 3.0 >> >> >> >> On Wednesday, October 26, 2022 at 8:01:41 PM UTC-7 vince wrote: >> >>> Testing each later version one-by-one to see when it goes belly up via 'git >>> checkout revnumberhere -- vantage.py' >>> >>> - 4.8.0 version looks ok when dropped into place over 4.9.1 weewx >>> - may-06th version 7024f seems ok as well >>> - may-18th version b0145 fails repeatedly with the 'max tries >>> exceeded' error >>> >>> debug=1 syslog entries from 'grep vantage /var/log/syslog' are in the >>> attachment. >>> I used 'logger' to write out which version driver I was starting up.... >>> >>> On Wednesday, October 26, 2022 at 3:46:35 PM UTC-7 Tom Keffer wrote: >>> >>>> How about trying the old V4.8.0 driver in v4.9.1? You can find it here: >>>> https://raw.githubusercontent.com/weewx/weewx/v4.8.0/bin/weewx/drivers/vantage.py >>>> >>>> On Wed, Oct 26, 2022 at 3:12 PM vince <vince...@gmail.com> wrote: >>>> >>>>> Almost every single time. Not 100% but pretty close. >>>>> >>>>> - I put the 4.9.1 driver on my working 4.8.0 system, deleted the >>>>> __pycache__ file for it, and started weewx up and it 'did' recreate >>>>> the >>>>> problem. Failed immediately and kept failing. >>>>> >>>>> >>>>> - I also repeated the test with the extra sensors stuff set to { } >>>>> and it didn't fix it. So I'm guessing it's the issue-772 mods are at >>>>> fault. >>>>> >>>>> If you can get me a driver with issue-772 backed out or with more >>>>> diagnostic logging etc added I'd be happy to do more tests to try to >>>>> figure >>>>> it out. >>>>> >>>>> Lastly, FWIW, I'm running a VP2 with rather old firmware, if that >>>>> matters. >>>>> >>>>> Davis Vantage EEPROM settings: >>>>> >>>>> CONSOLE TYPE: Vantage Pro2 >>>>> >>>>> CONSOLE FIRMWARE: >>>>> Date: Jul 14 2008 >>>>> Version: 1.80 >>>>> >>>>> CONSOLE SETTINGS: >>>>> Archive interval: 300 (seconds) >>>>> Altitude: 365 (foot) >>>>> Wind cup type: large >>>>> Rain bucket type: 0.01 inches >>>>> Rain year start: 10 >>>>> Onboard time: 2022-10-26 15:10:05 >>>>> >>>>> CONSOLE DISPLAY UNITS: >>>>> Barometer: inHg >>>>> Temperature: degree_F >>>>> Rain: inch >>>>> Wind: mile_per_hour >>>>> >>>>> CONSOLE STATION INFO: >>>>> Latitude (onboard): +47.3 >>>>> Longitude (onboard): -122.3 >>>>> Use manual or auto DST? AUTO >>>>> DST setting: N/A >>>>> Use GMT offset or zone code? GMT_OFFSET >>>>> Time zone code: N/A >>>>> GMT offset: -8.0 hours >>>>> Temperature logging: LAST >>>>> Retransmit channel: OFF (0) >>>>> >>>>> TRANSMITTERS: >>>>> Channel Receive Repeater Type >>>>> 1 active none iss >>>>> 2 inactive none (N/A) >>>>> 3 inactive none (N/A) >>>>> 4 inactive none (N/A) >>>>> 5 inactive none (N/A) >>>>> 6 inactive none (N/A) >>>>> 7 inactive none (N/A) >>>>> 8 inactive none (N/A) >>>>> >>>>> RECEPTION STATS: >>>>> Total packets received: 255 >>>>> Total packets missed: 3 >>>>> Number of resynchronizations: 0 >>>>> Longest good stretch: 122 >>>>> Number of CRC errors: 0 >>>>> >>>>> BAROMETER CALIBRATION DATA: >>>>> Current barometer reading: 30.130 inHg >>>>> Altitude: 365 feet >>>>> Dew point: 44 F >>>>> Virtual temperature: 46 F >>>>> Humidity correction factor: 1.9 >>>>> Correction ratio: 1.014 >>>>> Correction constant: +0.000 inHg >>>>> Gain: 0.000 >>>>> Offset: 35.000 >>>>> >>>>> OFFSETS: >>>>> Wind direction: +0 deg >>>>> Inside Temperature: +0.0 F >>>>> Inside Humidity: +0 % >>>>> Outside Temperature: +0.0 F >>>>> Outside Humidity: +0 % >>>>> >>>>> -- >>>>> >>>> You received this message because you are subscribed to the Google >>>>> Groups "weewx-user" group. >>>>> To unsubscribe from this group and stop receiving emails from it, send >>>>> an email to weewx-user+...@googlegroups.com. >>>>> >>>> To view this discussion on the web visit >>>>> https://groups.google.com/d/msgid/weewx-user/87a9b91d-265d-4c51-9fcf-4d8c7370a3dfn%40googlegroups.com >>>>> >>>>> <https://groups.google.com/d/msgid/weewx-user/87a9b91d-265d-4c51-9fcf-4d8c7370a3dfn%40googlegroups.com?utm_medium=email&utm_source=footer> >>>>> . >>>>> >>>> -- You received this message because you are subscribed to the Google Groups "weewx-user" group. To unsubscribe from this group and stop receiving emails from it, send an email to weewx-user+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/weewx-user/06b970bb-e498-43b2-a9fd-4d8e622e476an%40googlegroups.com.
