What if a tractor drives through the tower?
-----
Mike Hammett
Intelligent Computing Solutions
http://www.ics-il.com
On 9/25/2010 10:17 AM, Stuart Pierce wrote:
Are you serious ? What if the poe checkbox gets unchecked ?
---------- Original Message ----------------------------------
From: Philip Dorr<wirel...@judgementgaming.com>
Reply-To: WISPA General List<wireless@wispa.org>
Date: Sat, 25 Sep 2010 08:37:58 -0500
input power in the "secondary" port and use the "main" port to power
the second radio
On Fri, Sep 24, 2010 at 8:39 PM, Robert West<robert.w...@just-micro.com> wrote:
Eh? Â What ya mean???
-----Original Message-----
From: wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] On Behalf
Of Philip Dorr
Sent: Friday, September 24, 2010 9:14 PM
To: WISPA General List
Subject: Re: [WISPA] UBNT Nano5M Secondary RJ45 Port PoE Burnout!
It works perfectly fine if you power through the secondary port.
On Fri, Sep 24, 2010 at 8:05 PM, RickG<rgunder...@gmail.com> wrote:
I was skeptical of the poe passthrough sicne I first saw it and this is why.
On repeaters, it would be so tempting to just run one wire but I've
stuck with two. It will be interesting to see if it gets fixed. Thanks
for sharing!
On Fri, Sep 24, 2010 at 8:50 PM, Robert West
<robert.w...@just-micro.com>
wrote:
Today I finally figured out an Issue I’ve been having with a
NanoStation5M.  I have a customer who wanted service,  was in  trees
but had a hot signal out at the road. Â Dug a 4 foot hole, put in 2 10
foot sections of rigid conduit and 5 bags of concrete. Â Ran an
underground line of Cat5e, double shielded and flooded cable with
ground wire to his house. Â That was 5 months or so ago. Â At the
beginning of August, he called me and said his neighbor wanted
service. Â Same trees so I took the AirGrid down, put up a Nano5M and
plugged a Nano loco2 into the secondary port and shot it at a second
Nano Loco2 at his place. Â Replaced my weird Airgrid
Worked perfectly, everyone happy. Â 2 weeks ago I get a call, neighbor
not working. Â I go out, no power light on the Nano at the pole. Â I
figure, bad crimp…….  Take it down, make up a new wire to connect the two,
fires up.
All good. Â 2 days later, same issue. Â I reset it all to defaults,
reconfigure, all okay. Â 2 days later, same thing. Â I downgrade
firmware to 5.2.  Couple of days later, no signal again.  I’ll also
add I was getting some “weird�  lag at the AP that this setup was
feeding off of. Â So I was fighting two battles. Â Then today, I find
that the PoE Pass Through check box is empty. Â DUH! Â I check it,
apply, comes back empty. Â I do it again, same issue. Â I go out and I
can connect my laptop through the secondary port but it will not give any
voltage.
I checked my lag time issue at the AP. Â GONE!
I then checked in the UBNT forums………….  It’s an issue.  After 20
days
PoE on the secondary Nano port starts to die. Â Replaced it with
another Nano5M, working fine but looks like I’ll be coming up with
another MacGyver solution to service this dude……….
Just so ya knows.
Bob-
---------------------------------------------------------------------
-----------
WISPA Wants You! Join today!
http://signup.wispa.org/
---------------------------------------------------------------------
-----------
WISPA Wireless List: wireless@wispa.org
Subscribe/Unsubscribe:
http://lists.wispa.org/mailman/listinfo/wireless
Archives: http://lists.wispa.org/pipermail/wireless/
----------------------------------------------------------------------
----------
WISPA Wants You! Join today!
http://signup.wispa.org/
----------------------------------------------------------------------
----------
WISPA Wireless List: wireless@wispa.org
Subscribe/Unsubscribe:
http://lists.wispa.org/mailman/listinfo/wireless
Archives: http://lists.wispa.org/pipermail/wireless/
--------------------------------------------------------------------------------
WISPA Wants You! Join today!
http://signup.wispa.org/
--------------------------------------------------------------------------------
WISPA Wireless List: wireless@wispa.org
Subscribe/Unsubscribe:
http://lists.wispa.org/mailman/listinfo/wireless
Archives: http://lists.wispa.org/pipermail/wireless/
--------------------------------------------------------------------------------
WISPA Wants You! Join today!
http://signup.wispa.org/
--------------------------------------------------------------------------------
WISPA Wireless List: wireless@wispa.org
Subscribe/Unsubscribe:
http://lists.wispa.org/mailman/listinfo/wireless
Archives: http://lists.wispa.org/pipermail/wireless/
--------------------------------------------------------------------------------
WISPA Wants You! Join today!
http://signup.wispa.org/
--------------------------------------------------------------------------------
WISPA Wireless List: wireless@wispa.org
Subscribe/Unsubscribe:
http://lists.wispa.org/mailman/listinfo/wireless
Archives: http://lists.wispa.org/pipermail/wireless/
________________________________________________________________
Sent via the WebMail system at avolve.net
--------------------------------------------------------------------------------
WISPA Wants You! Join today!
http://signup.wispa.org/
--------------------------------------------------------------------------------
WISPA Wireless List: wireless@wispa.org
Subscribe/Unsubscribe:
http://lists.wispa.org/mailman/listinfo/wireless
Archives: http://lists.wispa.org/pipermail/wireless/
--------------------------------------------------------------------------------
WISPA Wants You! Join today!
http://signup.wispa.org/
--------------------------------------------------------------------------------
WISPA Wireless List: wireless@wispa.org
Subscribe/Unsubscribe:
http://lists.wispa.org/mailman/listinfo/wireless
Archives: http://lists.wispa.org/pipermail/wireless/
