Ah! I'll give that a shot. Thanks.
-----Original Message----- From: wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] On Behalf Of Philip Dorr Sent: Saturday, September 25, 2010 9:38 AM To: WISPA General List Subject: Re: [WISPA] UBNT Nano5M Secondary RJ45 Port PoE Burnout! input power in the "secondary" port and use the "main" port to power the second radio On Fri, Sep 24, 2010 at 8:39 PM, Robert West <robert.w...@just-micro.com> wrote: > Eh? What ya mean??? > > > -----Original Message----- > From: wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] On > Behalf Of Philip Dorr > Sent: Friday, September 24, 2010 9:14 PM > To: WISPA General List > Subject: Re: [WISPA] UBNT Nano5M Secondary RJ45 Port PoE Burnout! > > It works perfectly fine if you power through the secondary port. > > On Fri, Sep 24, 2010 at 8:05 PM, RickG <rgunder...@gmail.com> wrote: >> I was skeptical of the poe passthrough sicne I first saw it and this is why. >> On repeaters, it would be so tempting to just run one wire but I've >> stuck with two. It will be interesting to see if it gets fixed. Thanks >> for sharing! >> >> On Fri, Sep 24, 2010 at 8:50 PM, Robert West >> <robert.w...@just-micro.com> >> wrote: >>> >>> Today I finally figured out an Issue I’ve been having with a >>> NanoStation5M. I have a customer who wanted service, was in trees >>> but had a hot signal out at the road. Dug a 4 foot hole, put in 2 10 >>> foot sections of rigid conduit and 5 bags of concrete. Ran an >>> underground line of Cat5e, double shielded and flooded cable with >>> ground wire to his house. That was 5 months or so ago. At the >>> beginning of August, he called me and said his neighbor wanted >>> service. Same trees so I took the AirGrid down, put up a Nano5M and >>> plugged a Nano loco2 into the secondary port and shot it at a second >>> Nano Loco2 at his place. Replaced my weird Airgrid >>> >>> >>> >>> Worked perfectly, everyone happy. 2 weeks ago I get a call, neighbor >>> not working. I go out, no power light on the Nano at the pole. I >>> figure, bad crimp……. Take it down, make up a new wire to connect the two, >>> fires up. >>> All good. 2 days later, same issue. I reset it all to defaults, >>> reconfigure, all okay. 2 days later, same thing. I downgrade >>> firmware to 5.2. Couple of days later, no signal again. I’ll also >>> add I was getting some “weird” lag at the AP that this setup was >>> feeding off of. So I was fighting two battles. Then today, I find >>> that the PoE Pass Through check box is empty. DUH! I check it, >>> apply, comes back empty. I do it again, same issue. I go out and I >>> can connect my laptop through the secondary port but it will not give any >>> voltage. >>> >>> >>> >>> I checked my lag time issue at the AP. GONE! >>> >>> >>> >>> I then checked in the UBNT forums…………. It’s an issue. After 20 days >>> PoE on the secondary Nano port starts to die. Replaced it with >>> another Nano5M, working fine but looks like I’ll be coming up with >>> another MacGyver solution to service this dude………. >>> >>> >>> >>> Just so ya knows. >>> >>> >>> >>> Bob- >>> >>> >>> >>> >>> >>> >>> >>> >>> >>> >>> >>> --------------------------------------------------------------------- >>> ----------- >>> WISPA Wants You! Join today! >>> http://signup.wispa.org/ >>> >>> --------------------------------------------------------------------- >>> ----------- >>> >>> WISPA Wireless List: wireless@wispa.org >>> >>> Subscribe/Unsubscribe: >>> http://lists.wispa.org/mailman/listinfo/wireless >>> >>> Archives: http://lists.wispa.org/pipermail/wireless/ >> >> >> >> >> ---------------------------------------------------------------------- >> ---------- >> WISPA Wants You! Join today! >> http://signup.wispa.org/ >> ---------------------------------------------------------------------- >> ---------- >> >> WISPA Wireless List: wireless@wispa.org >> >> Subscribe/Unsubscribe: >> http://lists.wispa.org/mailman/listinfo/wireless >> >> Archives: http://lists.wispa.org/pipermail/wireless/ >> > > > -------------------------------------------------------------------------------- > WISPA Wants You! Join today! > http://signup.wispa.org/ > -------------------------------------------------------------------------------- > > WISPA Wireless List: wireless@wispa.org > > Subscribe/Unsubscribe: > http://lists.wispa.org/mailman/listinfo/wireless > > Archives: http://lists.wispa.org/pipermail/wireless/ > > > > -------------------------------------------------------------------------------- > WISPA Wants You! Join today! > http://signup.wispa.org/ > -------------------------------------------------------------------------------- > > WISPA Wireless List: wireless@wispa.org > > Subscribe/Unsubscribe: > http://lists.wispa.org/mailman/listinfo/wireless > > Archives: http://lists.wispa.org/pipermail/wireless/ -------------------------------------------------------------------------------- WISPA Wants You! Join today! http://signup.wispa.org/ -------------------------------------------------------------------------------- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/ -------------------------------------------------------------------------------- WISPA Wants You! Join today! http://signup.wispa.org/ -------------------------------------------------------------------------------- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/
