I get mine for .08325 cents each off of Alibaba (shipped). They work great.
On Tue, Jul 23, 2013 at 6:44 PM, Clay Stewart < cstew...@stewartcomputerservices.com> wrote: > Yes, after crimping any wire end pull tab out as most crimpers we have > used compress the tab. > > We use UBNT ends with no real issues... over a thousand plus with two > missing a single wire contact, which did cause a little time finding the > issue... but had seen this in other brands as well. > > Hopefully you do have a tech pulllng the plugs out hard from the NSsm > which will break the lock piece in the socket. > > > > On Tue, Jul 23, 2013 at 4:31 PM, Josh Luthman <j...@imaginenetworksllc.com > > wrote: > >> Pull the tab out a bit. >> >> Josh Luthman >> Office: 937-552-2340 >> Direct: 937-552-2343 >> 1100 Wayne St >> Suite 1337 >> Troy, OH 45373 >> On Jul 23, 2013 4:26 PM, "Dave Hulsebus" <cont...@portative.net> wrote: >> >>> ** >>> We found the last 3 boxes of Tough connectors we've purchased have had >>> issues staying snapped into NanoBridges. They just won't snap in and work >>> their way out just enough to cause failure over time. No issues with any >>> other radio's - just NB's. Has anyone else experienced this issue ? >>> >>> Dave >>> >>> ------------------------------ >>> *From:* wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] *On >>> Behalf Of *Marlon Schafer (509.982.2181) >>> *Sent:* Tuesday, July 23, 2013 2:30 PM >>> *To:* WISPA General List >>> *Subject:* Re: [WISPA] shielded rj45 ends >>> >>> Yes. >>> >>> There are two styles. One has no metal shielding, the other does. Both >>> are expensive (relatively) but I’m addicted to them. I love not having to >>> worry about how far back I strip things. Not having to worry about wires >>> crossing when pushed into the connector (I can check them before crimping) >>> etc. >>> >>> http://ezrj45.com/ezrj45plugs.php?gclid=CLSDvLWfxrgCFWXZQgodwlQANg >>> >>> Marsh cable stocks them. >>> >>> marlon >>> >>> >>> *From:* Kevin Owen <ko...@fsr.com> >>> *Sent:* Tuesday, July 23, 2013 11:21 AM >>> *To:* WISPA General List <wireless@wispa.org> >>> *Subject:* Re: [WISPA] shielded rj45 ends >>> >>> >>> Do they support shielded cabling?**** >>> >>> **** >>> >>> Kevin**** >>> >>> **** >>> >>> **** >>> >>> *From:* wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] *On >>> Behalf Of *Marlon Schafer (509.982.2181) >>> *Sent:* Tuesday, July 23, 2013 11:14 AM >>> *To:* WISPA General List >>> *Subject:* Re: [WISPA] shielded rj45 ends**** >>> >>> **** >>> >>> We love the EZ-RJ45 units. Get them from Marsh Cable.**** >>> >>> **** >>> >>> It’s the style where the wires go right through the ends of the >>> connectors and the crimper crimps and cuts at the same time. HUGE time >>> saver.**** >>> >>> **** >>> >>> marlon**** >>> >>> **** >>> >>> **** >>> >>> *From:* heith petersen <wi...@mncomm.com> **** >>> >>> *Sent:* Tuesday, July 23, 2013 6:50 AM**** >>> >>> *To:* wireless@wispa.org **** >>> >>> *Subject:* [WISPA] shielded rj45 ends**** >>> >>> **** >>> >>> I was curious what shielded ends members are using. I typically use the >>> cable that Cayman wireless sells, definitely not tough cable. I prefer the >>> UBNT tough ends as I have no issues with them, however some of my techs >>> dread them. I have purchased some other ends in the past but at a high >>> premium. Anyways just looking for some ideas as I am getting out voted on >>> the tough ends.**** >>> >>> **** >>> >>> thanks**** >>> >>> heith**** >>> ------------------------------ >>> >>> _______________________________________________ >>> Wireless mailing list >>> Wireless@wispa.org >>> http://lists.wispa.org/mailman/listinfo/wireless**** >>> >>> ------------------------------ >>> _______________________________________________ >>> Wireless mailing list >>> Wireless@wispa.org >>> http://lists.wispa.org/mailman/listinfo/wireless >>> >>> >>> _______________________________________________ >>> Wireless mailing list >>> Wireless@wispa.org >>> http://lists.wispa.org/mailman/listinfo/wireless >>> >>> >> _______________________________________________ >> Wireless mailing list >> Wireless@wispa.org >> http://lists.wispa.org/mailman/listinfo/wireless >> >> > > > -- > > > -- > SCS > Clay Stewart > CEO, Tye River Farms, Inc., > DBA Stewart Computer Services > 434.263.6363 O > 434.942.6510 C > cstew...@stewartcomputerservices.com > “We Keep You Up and Running” > Wireless Broadband > Programming > Network Services > > _______________________________________________ > Wireless mailing list > Wireless@wispa.org > http://lists.wispa.org/mailman/listinfo/wireless > >
_______________________________________________ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless