I never got OmniRig to behave for me. I just tested 1.18 on my system and it
works just fine. Installed 1.19 and can't get it to behave at all.
I now use FLRig and have WSJT-X, Log4OM, FLDigi, a custom tuner utility, and
another project under development all talking to FLRig at the same time without
any problems.
Any particular reason you're using OmniRig?
de Mike W9MDB
On Saturday, May 18, 2019, 7:29:23 AM CDT, Mike <[email protected]>
wrote:
Well, that's not what he says and I have no idea, I'm just reporting the
issue. He said he'd be in touch with your developers. I just want to make sure
it's been seen. Thanks.
On Sat, May 18, 2019 at 7:27 AM Black Michael via wsjt-devel
<[email protected]> wrote:
If it works in 1.16 and doesn't in 1.19 then it would seem to be OmniRig and
not WSJT-X. Alex must've broken it.
That frequency test has been in there for quite a while (a couple years
perhaps?) and nobody else has this problem. It would indicate OmniRig is
dropping the frequency change request to return to the requested frequency.
de Mike W9MDB
On Saturday, May 18, 2019, 6:55:01 AM CDT, Mike <[email protected]>
wrote:
I am forwarding this conversation to amke sure you all know about this ...
I was running Omnirig 1.16 for years. I saw there was a new version (1.19) so
installed it. Have two rigs in use in Omnirig: FT-450D & IC-7300. Were no
problems before with Omnirig or the communications to/from the radios.
Now with the new 1.19, suppose the FT-450D is turned on and it's freq. display
reads 50.313.00. When I start WSJT-X using the new Omnirig it changes the
frequency to 50.313.05 on the radio display, and WSJT-X shows it's 50.313 055.
If I use WSJT-X to change bands the "55" Hz never shows up again no mater what
band I go to. But shut it all down and start over, same thing happens. 55 Hz
is added to the freq, of the FT-450D.
On the IC-7300, same thing happens at first BUT - I can see the display briefly
flash an extra 55 Hz on the display, then it goes to the correct frequency in
an instant most of the time. However, this morning it kept the extra 55 Hz on
the display of the IC-7300. Changing bands causes the 55 Hz to go away from
then on (for that operating session) like the FT-450D.
If I go back to the .exe for Omnirig 1.16 - the problems all go away and all
radios act perfectly fine just as they always did for years. I did not change
any settings when I switched to the new version to cause this. However; after I
observed it happen with 1.19 I tried to change various settings such as baud
rate (also for the radios), time out and other items to no avail. In any case
it does NOT happen when I go back to Omnirig 1.16. Even with different
settings. Omnirig 1.16 causes no problems at all.
I wrote the developer of Omnirig and got this response -
Hi Mike,
Thank you for reporting the problem. The frequency change by 55 Hz is not a
bug, WSJTX makes this change on startup to determine
the frequency change step of the radio. The program is supposed to undo the
change, but for some reason this does not happen. I
will contact the WSJTX developers to see how we can fix this.
Please note that I released OmniRig 1.19 in order to fix some serious problems
that WSJTX had with the old version. These
problems are now fixed, but the glitch you have reported still requires
correction.
73 Alex VE3NEA
_______________________________________________
wsjt-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
_______________________________________________
wsjt-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
_______________________________________________
wsjt-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
