Hello Rich- Have you listened to the .wav files to see if they sound clean and undistorted?
Windows allows audio channels to be monitored. Open sound control panel > recording tab, locate input device > properties > listen tab > click listen to this device. Listen to the audio quality when the app fails to decode everything that’s in the waterfall. Bring up Task Manager > performance > open resource monitor > Memory and check if Standby memory is used up. That’s when my system starts acting strange. You may need to reboot more often. Hope this helps. Bill W2PKY Sent from my iPad > On Apr 16, 2021, at 1:47 PM, Mike Lewis <[email protected]> wrote: > > > I have been seeing cycles with only a few decode counts on busy bands > periodically > > I am usually run 2 WJST-X instances 24/7 comparing the decode count each > cycle of a new SDR rig while I am working on it, compared to my K3, both on > the same antenna. I watch the decode count number and waterfall images > constantly, but not the actual decodes much. I do not reboot very often, the > short decode count only happen to me once then back to normal. I blamed that > on the possibility the missing decodes would appear in the next decode group > as late decodes, but I have not verified that happens/happened. Need to look > at that next time. I usually see it a few times a day. I will look to see > if it is odd or even as well. This is 2.4.0-rc4. It occurred on earlier rc > versions, maybe on 2.3 also. > > Mike > K7MDL EL87sm & CN88sf > > From: Rich - K1HTV <[email protected]> > Sent: Friday, April 16, 2021 08:14 > To: WSJT <[email protected]> > Subject: [wsjt-devel] Few FT8 decodes on Even cycles > > In the past couple of months, using both the GA and the RC versions of > WSJT-X, I've been plagued with an intermittent decode problem while running > FT8. I am using Win10 on a dual core i5-2500 @ 3.3GHz with 16GB of RAM. It > may take days and sometimes less for the problem to occur. On a busy 20 Meter > band, the decode count and corresponding number of decodes are normally > between 30 and 60 per 15 second FT8 sequence. > > When the problem develops, with a full waterfall display, on the odd cycles, > only 4 to 8 signals are decoded and counted. On the even cycles only a few > and often NONE of the many dozen signals are decoded. The DT on most of the > few decoded signals is usually 0.1 seconds, so it's not a clock issue. > > The only fix is to reboot the computer and then the count goes back to the 30 > to 60 decodes on both even and odd 15 second cycles. > > When the problem occurs, checking with Task Manager, the max CPU usage on > WSJT-X peaks at less than 5% and the max total CPU usage with other apps is > no more than 20% on peaks. A max of 30% of the 16GB RAM is being used. I use > the Chrome browser, using 300-800MB of RAM. When I shut down Chrome and all > other apps, there doesn't appear to be any phantom occurrences of their > processes running, but the very poor decoding problem still exists. > > I turned on WSJT-X "Save all" and played back the saved WAV files and the > number of decodes matched the low counter readings noted for the same > sequences. I switched from using the Elecraft K3 USB CODEC to using the sound > card with audio from the K3 Line Out jack and get the same poor performance > when the problem arises. > > As I said, only a reboot of the computer will bring things back to normal. > I'm at a loss to figure out what is causing this intermittent problem and how > to correct it. Does anyone have any ideas of the cause and how it can be > fixed? Thanks. > > 73, > Rich - K1HTV > _______________________________________________ > wsjt-devel mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/wsjt-devel
_______________________________________________ wsjt-devel mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/wsjt-devel
