Even propane will get it hot enough. Propane is nice because it will not get
it hot enough to burn. You don’t want it turning yellow.
Red to Orange is ideal. One way to test to see if you got it hot enough is to
use a magnet. If it is hot enough a magnet will not attract it.
From: Adam Moffett
Sent: Tuesday, August 10, 2021 12:39 PM
To: af@af.afmug.com
Subject: Re: [AFMUG] Installer Drill Bits
Interesting tip.
Will a torch with MAP gas get it that hot, or do you need acetylene?
On 8/10/2021 2:36 PM, Chuck McCown via AF wrote:
If someone gets a bit too hot and it loses its hardness, you can heat it up
to cherry red, hold for a minute and then dunk in motor oil. Good trick for
old chisels too.
From: Steve Jones
Sent: Tuesday, August 10, 2021 10:39 AM
To: AnimalFarm Microwave Users Group
Subject: Re: [AFMUG] Installer Drill Bits
i quit caring about installers having good bits the billionth time i told
them that you dont use them on rock, and if you are using rock with the right
bit or not you need a hammer drill, and no, your impact isnt a hammer drill,
and your long bit goes back in the tube, not on a pile of gear on the floor. F
those tower monkeys, let them get their own bits
On Tue, Aug 10, 2021 at 10:47 AM Chuck McCown via AF <af@af.afmug.com> wrote:
Aluminum can be worked with wood working tools, no problem. I use wood
routers, chop saws etc on aluminum all the time.
One tip I learned after ruining carpets in double wides. Put the drill in
reverse when drilling through carpet.
-----Original Message-----
From: Adam Moffett
Sent: Tuesday, August 10, 2021 5:32 AM
To: af@af.afmug.com
Subject: Re: [AFMUG] Installer Drill Bits
When I did installs every day I would use the same 5/16" drill bit for
6-12 months. I know I could have sharpened them, but it was easier to
just get another one at Lowes.
IMO drill slower so it doesn't get too hot. When you're going through
metal set the drill on the lowest speed and use moderate pressure. You
want to see little flakes coming off the metal rather than dust. If the
metal is thick then put some oil on the bit to conduct heat away. WD-40
will work in a pinch, or a little can of 3-in-1 oil with the dropper
tip. Even on wood, don't go full speed unless it's a short hole. When
the wood is real chewy you might have to back out and in to clear debris
and let the tip rest. If you're getting smoke you're trashing that
bit. Aluminum siding is so thin I can't believe that's what ruins your
bits.
On 8/9/2021 6:02 PM, Nate Burke wrote:
> We've been getting the installer drill bits at the local big box store.
> The 1/4"x18" bit with the hole in the flute to hook the wire on and pull
> back. They are cheap, and have the lifespan to show. Drill a couple
> aluminum siding houses and it's time for a new one. I'm looking to get
> them higher quality ones. They seem hard to locate at other
distributors.
> Am I calling them the wrong thing? I was searching for either 'bell
hanger
> bit' or 'installer bit' I found some on Amazon, but they are probably
> about the same quality as the bigbox ones.
>
> I found one at Grainer that is backordered several weeks, and I haven't
> found one at McMaster yet. Am I calling them the wrong thing?
>
--
AF mailing list
AF@af.afmug.com
http://af.afmug.com/mailman/listinfo/af_af.afmug.com
--
AF mailing list
AF@af.afmug.com
http://af.afmug.com/mailman/listinfo/af_af.afmug.com
------------------------------------------------------------------------------
--
AF mailing list
AF@af.afmug.com
http://af.afmug.com/mailman/listinfo/af_af.afmug.com
--------------------------------------------------------------------------------
--
AF mailing list
AF@af.afmug.com
http://af.afmug.com/mailman/listinfo/af_af.afmug.com
--
AF mailing list
AF@af.afmug.com
http://af.afmug.com/mailman/listinfo/af_af.afmug.com
