Thanks Mat. I was talking about the thread that George posted. http://community.cambiumnetworks.com/t5/PMP-450/450d-losing-sync/td-p/45012
On Wed, Oct 7, 2015 at 11:29 AM, Matt Mangriotis < matt.mangrio...@cambiumnetworks.com> wrote: > Alignment tone was broken in 13.3. This is in the release notes. > Recommend you move to R13.4. > > > > I am unsure of the “manufacturing issue” you refer to. We have had a > couple reports that 450d units were affected by the same manufacturing > quality issue that affected some other 5 GHz 450 SMs (they share the same > electrical PCB). If you see the “ADI Communications Failure” as referenced > in the FSB (even if the serial numbers don’t appear in this list), please > let us know right away. > > > > > http://community.cambiumnetworks.com/t5/PMP-450/Field-Service-Bulletin-ADI-Catalina-R1-Chip-not-supported/m-p/43211 > > > > > > Matt > > > > *From:* Af [mailto:af-boun...@afmug.com] *On Behalf Of *Carl Peterson > *Sent:* Wednesday, October 07, 2015 9:49 AM > *To:* af@afmug.com > *Subject:* Re: [AFMUG] 450d 13.3 on 12.2.2 AP > > > > Doh. Anyone from Cambium want to chime in on the scope of the > manufacturing issue? > > FYI, We installed one today on an AP running 13.2.1.3 and it seems to > work fine but the aim tool isn't working. SM running 13.3 out of the box. > Is there an issue with the aim tone on these? > > > > On Tue, Oct 6, 2015 at 6:10 PM, George Skorup <geo...@cbcast.com> wrote: > > Uh oh? > > http://community.cambiumnetworks.com/t5/PMP-450/450d-losing-sync/td-p/45012 > > > > On 10/6/2015 2:41 PM, David wrote: > > Yeah, better move to 13.2 I have no issues with it across 14 of our sites. > > On 10/06/2015 10:59 AM, Brian Sullivan wrote: > > 13.1.2 and above brings a lot of needed performance, I would upgrade at > least to that. > > On 10/6/2015 10:41 AM, Carl Peterson wrote: > > Is there an issue with 13.3 SMs on 12.2.2 APs? We are testing the 450d > and it looks like it is connecting but really isn't. > > > > Any chance this is a polarity issue? All of our dished SMs are connecting > fine. I seem to remember an issue with some 450APs having H and V swapped > internally. > > > LUID: 037 - [0a-00-3e-xx-xx-xx] > <http://10.13.39.140:1080/?mac_esn=0a003eb29e8a> State: IN SESSION > (Encrypt Disabled) > Site Name: NAME > PMP 450 MIMO OFDM > Software Version: CANOPY 13.3 > FPGA Version: 112414 (DES, Sched, US/ETSI) P11 > Session Timeout: 0, AirDelay: 2950 ns, 29 bits (approximately 0.274 > miles (1449 feet)) > Session Count: 4, Reg Count: 4, Re-Reg Count: 0, Session Uptime: 24 > d, 21:26:07 > Power Level : -54.2 dBm Signal Strength Ratio : 7.0 dB V - H dB > Signal to Noise Ratio: 14 dB V / 0 dB H > Sustained Uplink Data Rate (AP): 65000 (kbps) > Uplink Burst Allocation (AP): 2500000 (kbit) > Sustained Downlink Data Rate (AP): 65000 (kbps) > Downlink Burst Allocation (AP): 2500000 (kbit) > Broadcast/Multicast Allocation (AP): 50000 (kbit) > Max Burst Uplink Rate (D): 0 (kbit) > Max Burst Downlink Rate (AP): 0 (kbit) > Low Priority Uplink CIR (D): 0 (kbps) > Low Priority Downlink CIR (D) > > > > > > > > > > > > -- > > Carl Peterson > > *PORT NETWORKS* > > 401 E Pratt St, Ste 2553 > > Baltimore, MD 21202 > > (410) 637-3707 > -- Carl Peterson *PORT NETWORKS* 401 E Pratt St, Ste 2553 Baltimore, MD 21202 (410) 637-3707