I would prefer that any chance of sharing? On Tue, Aug 9, 2016 at 6:20 PM, Trey Scarborough <[email protected]> wrote:
> I set mine up by default the long way. So that all traffic generated by > default from my routers is the Loopback address. Its good for > EOIP/BGP/IPSEC/Radius/Syslog/etc. Then again like I said I set it up from > the start this way so it can change a lot of configurations if you do it > after anything is programed to use another IP. > > > On 8/9/2016 12:53 PM, Faisal Imtiaz wrote: > >> There is reason why I suggested you go the short way. >> >> The long way, is the technical attribute that can offer you a fix, but I >> cringe t think of how it may affect your network. >> >> >> :) >> >> Faisal Imtiaz >> Snappy Internet & Telecom >> 7266 SW 48 Street >> Miami, FL 33155 >> Tel: 305 663 5518 x 232 >> >> Help-desk: (305)663-5518 Option 2 or Email: [email protected] >> >> ------------------------------------------------------------------------ >> >> *From: *"That One Guy /sarcasm" <[email protected]> >> *To: *[email protected] >> *Sent: *Tuesday, August 9, 2016 1:22:03 PM >> *Subject: *Re: [AFMUG] mikrotik present as loopback address >> >> can you detail the long way >> in this instance, I just want it to be if it is traffic generated by >> the router destined for tcp port 25 present as 1.2.3.4 but dont >> impact anything else, what I dont want to risk is OSPF breaking or >> dropping an EOIP tunnel because that traffic is presenting differently >> >> On Tue, Aug 9, 2016 at 12:14 PM, Faisal Imtiaz >> <[email protected] <mailto:[email protected]>> wrote: >> >> There is a long way to solve this problem and there is a short >> way to solve this problem. >> >> short way first:- >> >> Mikrotik supports user authentication on out bound mail, so all >> you need to do is create a valid email user account on our mail >> server and use those credentials in your MT router Email >> settings so that you don't need an 'open mail relay'. >> >> Long way:- >> >> There is a setting call set-pref-src= in the routing filters, >> which accomplishes what you are asking for, however you will >> have to figure out on how exactly to tailor it to work for your >> environment. (I had to find this setting for one of our Peering >> Routers, a bit of a long story). >> >> :) >> >> Faisal Imtiaz >> Snappy Internet & Telecom >> 7266 SW 48 Street >> Miami, FL 33155 >> Tel: 305 663 5518 x 232 <tel:305%20663%205518%20x%20232> >> >> Help-desk: (305)663-5518 <tel:%28305%29663-5518> Option 2 or >> Email: [email protected] >> >> ------------------------------------------------------------ >> ------------ >> >> *From: *"That One Guy /sarcasm" <[email protected] >> <mailto:[email protected]>> >> *To: *[email protected] <mailto:[email protected]> >> *Sent: *Tuesday, August 9, 2016 12:51:03 PM >> *Subject: *[AFMUG] mikrotik present as loopback address >> >> right or wrong, i want to set up an open mail relay on our >> network for mikrotik backups. I want to lock the relay down >> to only accept traffic from our internal subnet for loopback >> IPs on the site routers. How do I make specific traffic >> always present as the same IP no matter which interface it >> exits since i cant seem to find a way to masquerade the >> output chain >> if it is doable, is there also a way to add a line to our >> default configs that will set the presentation IP to >> whatever the loopback IP on that device is? >> >> -- >> If you only see yourself as part of the team but >> you don't see your team as part of yourself you have already >> failed as part of the team. >> >> >> >> >> -- >> If you only see yourself as part of the team but you don't see your >> team as part of yourself you have already failed as part of the team. >> >> > > -- If you only see yourself as part of the team but you don't see your team as part of yourself you have already failed as part of the team.
