So, if testing under power you will show errors like we're seeing? One
test will be good and another will show "abnormal"?
Faisal Imtiaz wrote:
. Netonix still shows cable errors though a
standard cable tester shows
if you are testing the cable with the radio plugged in, then this is normal..
Regards.
Faisal Imtiaz
Snappy Internet & Telecom
7266 SW 48 Street
Miami, FL 33155
Tel: 305 663 5518 x 232
Help-desk: (305)663-5518 Option 2 or Email: supp...@snappytelecom.net
----- Original Message -----
From: "CBB - Jay Fuller" <par...@cyberbroadband.net>
To: af@afmug.com
Sent: Thursday, June 15, 2017 6:58:57 PM
Subject: Re: [AFMUG] Netonix/Mimosa compatibility.
At the moment it's two Mimosa radios at one tower and one radio at
another that have the issue. We replaced our Shireen Cat 5 with Shireen
Cat 6 and Shireen connectors and the link negotiation problem seems to
have gotten better but the Netonix still shows cable errors though a
standard cable tester shows continuity and correct pin out. I may
contact Netonix and see if they can give me a clue as to what problem
their unit is detecting.
Bill Prince wrote:
Have you just plugged into a laptop or anything besides the Netonix?
We've had at least one situation with a bad port on a Netonix switch
that had symptoms similar to this.
bp
<part15sbs{at}gmail{dot}com>
On 6/15/2017 3:44 PM, Jay Weekley wrote:
We tried it on one radio of the four in question.
Faisal Imtiaz wrote:
hmm.. sounds like you have some other issue going on ...
Faisal Imtiaz
Snappy Internet & Telecom
7266 SW 48 Street
Miami, FL 33155
Tel: 305 663 5518 x 232
Help-desk: (305)663-5518 Option 2 or Email: supp...@snappytelecom.net
----- Original Message -----
From: "CBB - Jay Fuller" <par...@cyberbroadband.net>
To: af@afmug.com
Sent: Thursday, June 15, 2017 6:03:05 PM
Subject: Re: [AFMUG] Netonix/Mimosa compatibility.
We tried the Mimosa brick and it didn't help but that was prior to
trying Mimosa's suggestion of moving to Cat6 . We've tried locking
it to
100 meg full duplex and it held a connection but I am not sure if we
tried 1 gig half.
Faisal Imtiaz wrote:
Here is what I would suggest.
1) Use the Mimosa Brick, for testing, and see if that fixes your
issue
if it does then consider, using a different port or 48VH
power etc to see if the
issue is on then netonix side.
if you still have the same issue with Mimosa Brick then you
know the problem is
else ware.
BWT.. if you lock both sides (Radio & Netonix) to 100meg full
duplex or even 1G
half duplex do they hold the connection ?
Regards.
Faisal Imtiaz
Snappy Internet & Telecom
7266 SW 48 Street
Miami, FL 33155
Tel: 305 663 5518 x 232
Help-desk: (305)663-5518 Option 2 or Email: supp...@snappytelecom.net
----- Original Message -----
From: "CBB - Jay Fuller" <par...@cyberbroadband.net>
To: af@afmug.com
Sent: Thursday, June 15, 2017 5:06:16 PM
Subject: Re: [AFMUG] Netonix/Mimosa compatibility.
Oh, and no surge protector at the moment.
Faisal Imtiaz wrote:
have not seen that issue ...
Are you using 48VH port ? or just 48V ?
and is there a surge protector in the middle ?
Regards
Faisal Imtiaz
Snappy Internet & Telecom
7266 SW 48 Street
Miami, FL 33155
Tel: 305 663 5518 x 232
Help-desk: (305)663-5518 Option 2 or Email:
supp...@snappytelecom.net
----- Original Message -----
From: "CBB - Jay Fuller" <par...@cyberbroadband.net>
To: af@afmug.com
Sent: Thursday, June 15, 2017 4:44:38 PM
Subject: [AFMUG] Netonix/Mimosa compatibility.
Has anyone experience a compatibility problem when using Mimosa
radios
with Netonix for power? We've got a problem with gigabit link
negotiation issues where link will alternate between a gig and
no link.
We've upgraded to Cat 6 and are still seeing the issue.
---
This email has been checked for viruses by AVG.
http://www.avg.com
