On Sun, Jan 14, 2024 at 12:28:17PM -0800, Mike Larkin wrote: > On Sun, Jan 14, 2024 at 09:13:54PM +0100, Mizsei Zoltán wrote: > > Hi, > > > > I have messing with OpenBSD current on my LinkStar H68K ARM box, based on > > the Rockchip RK3568 SOC. Originally it had an unsupported Mediatek wlan > > card, which i have replaced it with an intel one i had lying around. > > While OBSD recognizes the installed card, it categorically states it is > > not-configured, while it supposed to be supported by the iwn driver. > > > > Sadly i did not made any photo about the card i have installed, and the > > device is tricky to disassemble, but AFAIR the installed card is 0x8086, > > 0x088f, "Intel Centrino Advanced-N 6235. What could cause a device > > mis-recognition? > > > > Any idea what's going on here? > > > > Best Regards, > > --Zoltan > > > > iwn* at pci? is not in arm64 GENERIC. > > You might try adding that line to /sys/arch/arm64/conf/GENERIC (look for iwx > just toss it after that). It might work. > > -ml
also in case it wasn't obvious, you need to reconfigure the kernel and rebuild after doing that. > > > OpenBSD 7.4-current (GENERIC.MP) #40: Wed Jan 10 02:01:40 MST 2024 > > [email protected]:/usr/src/sys/arch/arm64/compile/GENERIC.MP > > real mem = 3959590912 (3776MB) > > avail mem = 3755196416 (3581MB) > > random: good seed from bootblocks > > mainbus0 at root: HINLINK OPC-H68K Board > > psci0 at mainbus0: PSCI 1.1, SMCCC 1.2, SYSTEM_SUSPEND > > efi0 at mainbus0: UEFI 2.7 > > efi0: EDK2 rev 0x10000 > > smbios0 at efi0: SMBIOS 3.3.0 > > smbios0: vendor EDK2 version "miq" date 12/16/2023 > > smbios0: Firefly Firefly ROC-RK3568-PC > > cpu0 at mainbus0 mpidr 0: ARM Cortex-A55 r2p0 > > cpu0: 32KB 64b/line 4-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache > > cpu0: 512KB 64b/line 16-way L2 cache > > cpu0: > > DP,RDM,Atomic,CRC32,SHA2,SHA1,AES+PMULL,LRCPC,DPB,ASID16,PAN+ATS1E1,LO,HPDS,VH,HAFDBS,SBSS > > cpu1 at mainbus0 mpidr 100: ARM Cortex-A55 r2p0 > > cpu1: 32KB 64b/line 4-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache > > cpu1: 512KB 64b/line 16-way L2 cache > > cpu1: > > DP,RDM,Atomic,CRC32,SHA2,SHA1,AES+PMULL,LRCPC,DPB,ASID16,PAN+ATS1E1,LO,HPDS,VH,HAFDBS,SBSS > > cpu2 at mainbus0 mpidr 200: ARM Cortex-A55 r2p0 > > cpu2: 32KB 64b/line 4-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache > > cpu2: 512KB 64b/line 16-way L2 cache > > cpu2: > > DP,RDM,Atomic,CRC32,SHA2,SHA1,AES+PMULL,LRCPC,DPB,ASID16,PAN+ATS1E1,LO,HPDS,VH,HAFDBS,SBSS > > cpu3 at mainbus0 mpidr 300: ARM Cortex-A55 r2p0 > > cpu3: 32KB 64b/line 4-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache > > cpu3: 512KB 64b/line 16-way L2 cache > > cpu3: > > DP,RDM,Atomic,CRC32,SHA2,SHA1,AES+PMULL,LRCPC,DPB,ASID16,PAN+ATS1E1,LO,HPDS,VH,HAFDBS,SBSS > > scmi0 at mainbus0: SCMI 2.0 > > apm0 at mainbus0 > > agintc0 at mainbus0 mbi shift 4:4 nirq 352 nredist 4 ipi: 0, 1, 2: > > "interrupt-controller" > > syscon0 at mainbus0: "syscon" > > rkiovd0 at syscon0 > > syscon1 at mainbus0: "syscon" > > syscon2 at mainbus0: "syscon" > > syscon3 at mainbus0: "syscon" > > syscon4 at mainbus0: "syscon" > > syscon5 at mainbus0: "syscon" > > syscon6 at mainbus0: "syscon" > > rkclock0 at mainbus0: PMUCRU > > rkclock1 at mainbus0: CRU > > syscon7 at mainbus0: "power-management" > > "power-controller" at syscon7 not configured > > syscon8 at mainbus0: "qos" > > syscon9 at mainbus0: "qos" > > syscon10 at mainbus0: "qos" > > syscon11 at mainbus0: "qos" > > syscon12 at mainbus0: "qos" > > syscon13 at mainbus0: "qos" > > syscon14 at mainbus0: "qos" > > syscon15 at mainbus0: "qos" > > syscon16 at mainbus0: "qos" > > syscon17 at mainbus0: "qos" > > syscon18 at mainbus0: "qos" > > syscon19 at mainbus0: "qos" > > syscon20 at mainbus0: "qos" > > syscon21 at mainbus0: "qos" > > syscon22 at mainbus0: "qos" > > syscon23 at mainbus0: "qos" > > syscon24 at mainbus0: "qos" > > syscon25 at mainbus0: "qos" > > syscon26 at mainbus0: "qos" > > syscon27 at mainbus0: "qos" > > syscon28 at mainbus0: "qos" > > syscon29 at mainbus0: "qos" > > syscon30 at mainbus0: "qos" > > syscon31 at mainbus0: "qos" > > rkcomphy0 at mainbus0 > > rkcomphy1 at mainbus0 > > rkusbphy0 at mainbus0: phy 0 > > rkusbphy1 at mainbus0: phy 1 > > rkpinctrl0 at mainbus0: "pinctrl" > > rkgpio0 at rkpinctrl0 > > rkgpio1 at rkpinctrl0 > > rkgpio2 at rkpinctrl0 > > rkgpio3 at rkpinctrl0 > > rkgpio4 at rkpinctrl0 > > syscon32 at mainbus0: "syscon" > > syscon33 at mainbus0: "qos" > > syscon34 at mainbus0: "qos" > > syscon35 at mainbus0: "qos" > > syscon36 at mainbus0: "syscon" > > rkpciephy0 at mainbus0 > > rkcomphy2 at mainbus0 > > "fit-images" at mainbus0 not configured > > "opp-table-0" at mainbus0 not configured > > "display-subsystem" at mainbus0 not configured > > "firmware" at mainbus0 not configured > > "opp-table-1" at mainbus0 not configured > > simpleaudio0 at mainbus0 > > "pmu" at mainbus0 not configured > > agtimer0 at mainbus0: 24000 kHz > > "xin24m" at mainbus0 not configured > > "xin32k" at mainbus0 not configured > > "sram" at mainbus0 not configured > > xhci0 at mainbus0, xHCI 1.10 > > usb0 at xhci0: USB revision 3.0 > > uhub0 at usb0 configuration 1 interface 0 "Generic xHCI root hub" rev > > 3.00/1.00 addr 1 > > ehci0 at mainbus0 > > usb1 at ehci0: USB revision 2.0 > > uhub1 at usb1 configuration 1 interface 0 "Generic EHCI root hub" rev > > 2.00/1.00 addr 1 > > ohci0 at mainbus0: version 1.0 > > ehci1 at mainbus0 > > usb2 at ehci1: USB revision 2.0 > > uhub2 at usb2 configuration 1 interface 0 "Generic EHCI root hub" rev > > 2.00/1.00 addr 1 > > ohci1 at mainbus0: version 1.0 > > rkiic0 at mainbus0 > > iic0 at rkiic0 > > fanpwr0 at iic0 addr 0x1c: TCS4525, 1.15 VDC > > rkpmic0 at iic0 addr 0x20: RK809 > > rkpwm0 at mainbus0rkclock_get_frequency(rkclock0, 13) > > : no clock > > "gpu" at mainbus0 not configured > > "video-codec" at mainbus0 not configured > > "iommu" at mainbus0 not configured > > "rga" at mainbus0 not configured > > "video-codec" at mainbus0 not configured > > "iommu" at mainbus0 not configured > > dwqe0 at mainbus0 gmac 1: rev 0x51, address 3e:68:a7:8e:7e:25 > > rgephy0 at dwqe0 phy 0: RTL8169S/8110S/8211 PHY, rev. 6 > > "vop" at mainbus0 not configured > > "iommu" at mainbus0 not configured > > "hdmi" at mainbus0 not configured > > dwpcie0 at mainbus0 > > dwmmc0 at mainbus0: 50 MHz base clock > > sdmmc0 at dwmmc0: 4-bit, sd high-speed, dma > > dwmshc0 at mainbus0 > > dwmshc0: SDHC 4.20, 200 MHz base clock > > sdmmc1 at dwmshc0: 8-bit, sd high-speed, mmc high-speed, dma > > "i2s" at mainbus0 not configured > > "i2s" at mainbus0 not configured > > "dma-controller" at mainbus0 not configured > > "dma-controller" at mainbus0 not configured > > rkiic1 at mainbus0 > > iic1 at rkiic1 > > "watchdog" at mainbus0 not configured > > com0 at mainbus0: dw16550, 64 byte fifo > > rktemp0 at mainbus0 > > "saradc" at mainbus0 not configured > > ahci0 at mainbus0: AHCI 1.3 > > scsibus0 at ahci0: 32 targets > > dwpcie1 at mainbus0 > > dwpcie2 at mainbus0 > > dwqe1 at mainbus0 gmac 0: rev 0x51, address 3e:68:a7:8e:7e:24 > > rgephy1 at dwqe1 phy 0: RTL8169S/8110S/8211 PHY, rev. 6 > > rkrng0 at mainbus0: ver 2 > > "hdmi-con" at mainbus0 not configured > > gpiokeys0 at mainbus0: "reset" > > gpioleds0 at mainbus0: no LEDs > > "vcc12v-dcin" at mainbus0 not configured > > "vcc3v3-sys" at mainbus0 not configured > > "vcc5v0-sys" at mainbus0 not configured > > "vcc5v0-usb" at mainbus0 not configured > > "vcc5v0-usb-host" at mainbus0 not configured > > "vcc3v3-pcie" at mainbus0 not configured > > simpleaudio1 at mainbus0 > > pwmfan0 at mainbus0 > > simplefb0 at mainbus0: 3840x2160, 32bpp > > wsdisplay0 at simplefb0 mux 1: console (std, vt100 emulation) > > wsdisplay0: screen 1-5 added (std, vt100 emulation) > > usb3 at ohci0: USB revision 1.0 > > uhub3 at usb3 configuration 1 interface 0 "Generic OHCI root hub" rev > > 1.00/1.00 addr 1 > > usb4 at ohci1: USB revision 1.0 > > uhub4 at usb4 configuration 1 interface 0 "Generic OHCI root hub" rev > > 1.00/1.00 addr 1 > > pci0 at dwpcie0 > > ppb0 at pci0 dev 0 function 0 "Rockchip RK3566" rev 0x00 > > pci1 at ppb0 bus 1 > > "Intel WiFi Link 1030" rev 0x1a at pci1 dev 0 function 0 not configured > > pci2 at dwpcie1 > > ppb1 at pci2 dev 0 function 0 "Rockchip RK3566" rev 0x00 > > pci3 at ppb1 bus 1 > > rge0 at pci3 dev 0 function 0 "Realtek RTL8125" rev 0x05: msi, address > > 00:00:00:00:00:00 > > pci4 at dwpcie2 > > ppb2 at pci4 dev 0 function 0 "Rockchip RK3566" rev 0x00 > > pci5 at ppb2 bus 1 > > rge1 at pci5 dev 0 function 0 "Realtek RTL8125" rev 0x05: msi, address > > 00:00:00:00:00:00 > > scsibus1 at sdmmc0: 2 targets, initiator 0 > > sd0 at scsibus1 targ 1 lun 0: <SD/MMC, NCard, 0010> removable > > sd0: 14910MB, 512 bytes/sector, 30535680 sectors > > sdmmc1: can't enable card > > sdhc_sdclk_frequency_select: command in progress > > umass0 at uhub0 port 2 configuration 1 interface 0 "USB SanDisk 3.2Gen1" > > rev 3.20/1.00 addr 2 > > umass0: using SCSI over Bulk-Only > > scsibus2 at umass0: 2 targets, initiator 0 > > sd1 at scsibus2 targ 1 lun 0: <USB, SanDisk 3.2Gen1, 1.00> removable > > serial.0781558381075e2a041c > > sd1: 29340MB, 512 bytes/sector, 60088320 sectors > > uhidev0 at uhub4 port 1 configuration 1 interface 0 "Logitech USB Keyboard" > > rev 1.10/64.02 addr 2 > > uhidev0: iclass 3/1 > > ukbd0 at uhidev0: 8 variable keys, 6 key codes > > wskbd0 at ukbd0: console keyboard, using wsdisplay0 > > uhidev1 at uhub4 port 1 configuration 1 interface 1 "Logitech USB Keyboard" > > rev 1.10/64.02 addr 2 > > uhidev1: iclass 3/0, 5 report ids > > ucc0 at uhidev1 reportid 1: 2 usages, 3 keys, enum > > wskbd1 at ucc0 mux 1 > > wskbd1: connecting to wsdisplay0 > > uhid0 at uhidev1 reportid 2: input=1, output=0, feature=0 > > ucc1 at uhidev1 reportid 3: 21 usages, 14 keys, enum > > wskbd2 at ucc1 mux 1 > > wskbd2: connecting to wsdisplay0 > > uhid1 at uhidev1 reportid 5: input=0, output=0, feature=5 > > vscsi0 at root > > scsibus3 at vscsi0: 256 targets > > softraid0 at root > > scsibus4 at softraid0: 256 targets > > root on sd1a (d9b3f31cd079d97e.a) swap on sd1b dump on sd1b > > WARNING: bad clock chip time > > WARNING: CHECK AND RESET THE DATE! > > linkstar$ > > linkstar$ > > linkstar$ > > linkstar$ uname -a > > OpenBSD linkstar.extrowerk.com 7.4 GENERIC.MP#40 arm64 > > linkstar$ doas pcidump -v > > doas ([email protected]) password: > > Domain /dev/pci0: > > 0:0:0: Rockchip RK3566 > > 0x0000: Vendor ID: 1d87, Product ID: 3566 > > 0x0004: Command: 0007, Status: 0010 > > 0x0008: Class: 06 Bridge, Subclass: 04 PCI, > > Interface: 00, Revision: 00 > > 0x000c: BIST: 00, Header Type: 01, Latency Timer: 00, > > Cache Line Size: 00 > > 0x0010: BAR empty (00000000) > > 0x0014: BAR empty (00000000) > > 0x0018: Primary Bus: 0, Secondary Bus: 1, Subordinate Bus: 15, > > Secondary Latency Timer: 00 > > 0x001c: I/O Base: 01, I/O Limit: f1, Secondary Status: 0000 > > 0x0020: Memory Base: f420, Memory Limit: f5f0 > > 0x0024: Prefetch Memory Base: 4001, Prefetch Memory Limit: 7ff1 > > 0x0028: Prefetch Memory Base Upper 32 Bits: 00000000 > > 0x002c: Prefetch Memory Limit Upper 32 Bits: 00000000 > > 0x0030: I/O Base Upper 16 Bits: f410, I/O Limit Upper 16 Bits: f41f > > 0x0038: Expansion ROM Base Address: 00000000 > > 0x003c: Interrupt Pin: 01, Line: ff, Bridge Control: 0000 > > 0x0040: Capability 0x01: Power Management > > State: D0 > > 0x0050: Capability 0x05: Message Signalled Interrupts (MSI) > > Enabled: no > > 0x0070: Capability 0x10: PCI Express > > Max Payload Size: 128 / 128 bytes > > Max Read Request Size: 512 bytes > > Link Speed: 2.5 / 8.0 GT/s > > Link Width: x1 / x1 > > 0x0100: Enhanced Capability 0x01: Advanced Error Reporting > > 0x0148: Enhanced Capability 0x19: Secondary PCIe Capability > > 0x0160: Enhanced Capability 0x1e: L1 PM > > 0x0170: Enhanced Capability 0x0b: Vendor-Specific > > 0x00b0: Capability 0x11: Extended Message Signalled Interrupts > > (MSI-X) > > Enabled: no; table size 1 (BAR 0:0) > > 1:0:0: Intel WiFi Link 1030 > > 0x0000: Vendor ID: 8086, Product ID: 008a > > 0x0004: Command: 0000, Status: 0010 > > 0x0008: Class: 02 Network, Subclass: 80 Miscellaneous, > > Interface: 00, Revision: 1a > > 0x000c: BIST: 00, Header Type: 00, Latency Timer: 00, > > Cache Line Size: 00 > > 0x0010: BAR mem 64bit addr: 0x0000000000000000/0x00002000 > > 0x0018: BAR empty (00000000) > > 0x001c: BAR empty (00000000) > > 0x0020: BAR empty (00000000) > > 0x0024: BAR empty (00000000) > > 0x0028: Cardbus CIS: 00000000 > > 0x002c: Subsystem Vendor ID: 8086 Product ID: 0000 > > 0x0030: Expansion ROM Base Address: 00000000 > > 0x0038: 00000000 > > 0x003c: Interrupt Pin: 01 Line: 00 Min Gnt: 00 Max Lat: 00 > > 0x00c8: Capability 0x01: Power Management > > State: D0 > > 0x00d0: Capability 0x05: Message Signalled Interrupts (MSI) > > Enabled: no > > 0x00e0: Capability 0x10: PCI Express > > Max Payload Size: 128 / 128 bytes > > Max Read Request Size: 128 bytes > > Link Speed: 2.5 / 2.5 GT/s > > Link Width: x1 / x1 > > 0x0100: Enhanced Capability 0x01: Advanced Error Reporting > > 0x0140: Enhanced Capability 0x03: Device Serial Number > > Serial Number: 000000ffff000000 > > Domain /dev/pci1: > > 0:0:0: Rockchip RK3566 > > 0x0000: Vendor ID: 1d87, Product ID: 3566 > > 0x0004: Command: 0007, Status: 0010 > > 0x0008: Class: 06 Bridge, Subclass: 04 PCI, > > Interface: 00, Revision: 00 > > 0x000c: BIST: 00, Header Type: 01, Latency Timer: 00, > > Cache Line Size: 00 > > 0x0010: BAR empty (00000000) > > 0x0014: BAR empty (00000000) > > 0x0018: Primary Bus: 0, Secondary Bus: 1, Subordinate Bus: 15, > > Secondary Latency Timer: 00 > > 0x001c: I/O Base: 01, I/O Limit: f1, Secondary Status: 0000 > > 0x0020: Memory Base: f220, Memory Limit: f3f0 > > 0x0024: Prefetch Memory Base: 4001, Prefetch Memory Limit: 7ff1 > > 0x0028: Prefetch Memory Base Upper 32 Bits: 00000000 > > 0x002c: Prefetch Memory Limit Upper 32 Bits: 00000000 > > 0x0030: I/O Base Upper 16 Bits: f210, I/O Limit Upper 16 Bits: f21f > > 0x0038: Expansion ROM Base Address: 00000000 > > 0x003c: Interrupt Pin: 01, Line: ff, Bridge Control: 0000 > > 0x0040: Capability 0x01: Power Management > > State: D0 > > 0x0050: Capability 0x05: Message Signalled Interrupts (MSI) > > Enabled: no > > 0x0070: Capability 0x10: PCI Express > > Max Payload Size: 128 / 256 bytes > > Max Read Request Size: 512 bytes > > Link Speed: 2.5 / 8.0 GT/s > > Link Width: x1 / x1 > > 0x0100: Enhanced Capability 0x01: Advanced Error Reporting > > 0x0148: Enhanced Capability 0x19: Secondary PCIe Capability > > 0x0160: Enhanced Capability 0x1e: L1 PM > > 0x0170: Enhanced Capability 0x0b: Vendor-Specific > > 0x00b0: Capability 0x11: Extended Message Signalled Interrupts > > (MSI-X) > > Enabled: no; table size 128 (BAR 4:131072) > > 1:0:0: Realtek RTL8125 > > 0x0000: Vendor ID: 10ec, Product ID: 8125 > > 0x0004: Command: 0006, Status: 0010 > > 0x0008: Class: 02 Network, Subclass: 00 Ethernet, > > Interface: 00, Revision: 05 > > 0x000c: BIST: 00, Header Type: 00, Latency Timer: 00, > > Cache Line Size: 00 > > 0x0010: BAR io addr: 0x00000000/0x0100 > > 0x0014: BAR empty (00000000) > > 0x0018: BAR mem 64bit addr: 0x00000000f2200000/0x00010000 > > 0x0020: BAR mem 64bit addr: 0x0000000000000000/0x00004000 > > 0x0028: Cardbus CIS: 00000000 > > 0x002c: Subsystem Vendor ID: 10ec Product ID: 8125 > > 0x0030: Expansion ROM Base Address: 00000000 > > 0x0038: 00000000 > > 0x003c: Interrupt Pin: 01 Line: ff Min Gnt: 00 Max Lat: 00 > > 0x0040: Capability 0x01: Power Management > > State: D0 > > 0x0050: Capability 0x05: Message Signalled Interrupts (MSI) > > Enabled: yes > > 0x0070: Capability 0x10: PCI Express > > Max Payload Size: 128 / 256 bytes > > Max Read Request Size: 512 bytes > > Link Speed: 2.5 / 5.0 GT/s > > Link Width: x1 / x1 > > 0x0100: Enhanced Capability 0x01: Advanced Error Reporting > > 0x0148: Enhanced Capability 0x02: Virtual Channel Capability > > 0x0168: Enhanced Capability 0x03: Device Serial Number > > Serial Number: 0000000000000000 > > 0x0178: Enhanced Capability 0x17: TPH Requester > > 0x0204: Enhanced Capability 0x18: Latency Tolerance Reporting > > 0x020c: Enhanced Capability 0x1e: L1 PM > > 0x021c: Enhanced Capability 0x0b: Vendor-Specific > > 0x00b0: Capability 0x11: Extended Message Signalled Interrupts > > (MSI-X) > > Enabled: no; table size 32 (BAR 4:0) > > 0x00d0: Capability 0x03: Vital Product Data (VPD) > > 7f: [|vpd] > > Domain /dev/pci2: > > 0:0:0: Rockchip RK3566 > > 0x0000: Vendor ID: 1d87, Product ID: 3566 > > 0x0004: Command: 0007, Status: 0010 > > 0x0008: Class: 06 Bridge, Subclass: 04 PCI, > > Interface: 00, Revision: 00 > > 0x000c: BIST: 00, Header Type: 01, Latency Timer: 00, > > Cache Line Size: 00 > > 0x0010: BAR mem 64bit addr: 0x0000000000000000/0x40000000 > > 0x0018: Primary Bus: 0, Secondary Bus: 1, Subordinate Bus: 15, > > Secondary Latency Timer: 00 > > 0x001c: I/O Base: 01, I/O Limit: f1, Secondary Status: 0000 > > 0x0020: Memory Base: f020, Memory Limit: f1f0 > > 0x0024: Prefetch Memory Base: 4001, Prefetch Memory Limit: 7ff1 > > 0x0028: Prefetch Memory Base Upper 32 Bits: 00000000 > > 0x002c: Prefetch Memory Limit Upper 32 Bits: 00000000 > > 0x0030: I/O Base Upper 16 Bits: f010, I/O Limit Upper 16 Bits: f01f > > 0x0038: Expansion ROM Base Address: 00000000 > > 0x003c: Interrupt Pin: 01, Line: ff, Bridge Control: 0000 > > 0x0040: Capability 0x01: Power Management > > State: D0 > > 0x0050: Capability 0x05: Message Signalled Interrupts (MSI) > > Enabled: no > > 0x0070: Capability 0x10: PCI Express > > Max Payload Size: 128 / 256 bytes > > Max Read Request Size: 512 bytes > > Link Speed: 5.0 / 8.0 GT/s > > Link Width: x1 / x2 > > 0x0100: Enhanced Capability 0x01: Advanced Error Reporting > > 0x0148: Enhanced Capability 0x19: Secondary PCIe Capability > > 0x0160: Enhanced Capability 0x1e: L1 PM > > 0x01a0: Enhanced Capability 0x0b: Vendor-Specific > > 0x02a0: Enhanced Capability 0x0b: Vendor-Specific > > 0x00b0: Capability 0x11: Extended Message Signalled Interrupts > > (MSI-X) > > Enabled: no; table size 128 (BAR 4:131072) > > 1:0:0: Realtek RTL8125 > > 0x0000: Vendor ID: 10ec, Product ID: 8125 > > 0x0004: Command: 0006, Status: 0010 > > 0x0008: Class: 02 Network, Subclass: 00 Ethernet, > > Interface: 00, Revision: 05 > > 0x000c: BIST: 00, Header Type: 00, Latency Timer: 00, > > Cache Line Size: 00 > > 0x0010: BAR io addr: 0x00000000/0x0100 > > 0x0014: BAR empty (00000000) > > 0x0018: BAR mem 64bit addr: 0x00000000f0200000/0x00010000 > > 0x0020: BAR mem 64bit addr: 0x0000000000000000/0x00004000 > > 0x0028: Cardbus CIS: 00000000 > > 0x002c: Subsystem Vendor ID: 10ec Product ID: 8125 > > 0x0030: Expansion ROM Base Address: 00000000 > > 0x0038: 00000000 > > 0x003c: Interrupt Pin: 01 Line: ff Min Gnt: 00 Max Lat: 00 > > 0x0040: Capability 0x01: Power Management > > State: D0 > > 0x0050: Capability 0x05: Message Signalled Interrupts (MSI) > > Enabled: yes > > 0x0070: Capability 0x10: PCI Express > > Max Payload Size: 128 / 256 bytes > > Max Read Request Size: 512 bytes > > Link Speed: 5.0 / 5.0 GT/s > > Link Width: x1 / x1 > > 0x0100: Enhanced Capability 0x01: Advanced Error Reporting > > 0x0148: Enhanced Capability 0x02: Virtual Channel Capability > > 0x0168: Enhanced Capability 0x03: Device Serial Number > > Serial Number: 0000000000000000 > > 0x0178: Enhanced Capability 0x17: TPH Requester > > 0x0204: Enhanced Capability 0x18: Latency Tolerance Reporting > > 0x020c: Enhanced Capability 0x1e: L1 PM > > 0x021c: Enhanced Capability 0x0b: Vendor-Specific > > 0x00b0: Capability 0x11: Extended Message Signalled Interrupts > > (MSI-X) > > Enabled: no; table size 32 (BAR 4:0) > > 0x00d0: Capability 0x03: Vital Product Data (VPD) > > 7f: [|vpd] > > linkstar$ ifconfig > > lo0: flags=2008049<UP,LOOPBACK,RUNNING,MULTICAST,LRO> mtu 32768 > > index 6 priority 0 llprio 3 > > groups: lo > > inet6 ::1 prefixlen 128 > > inet6 fe80::1%lo0 prefixlen 64 scopeid 0x6 > > inet 127.0.0.1 netmask 0xff000000 > > dwqe0: flags=808843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST,AUTOCONF4> mtu > > 1500 > > lladdr 3e:68:a7:8e:7e:25 > > index 1 priority 0 llprio 3 > > media: Ethernet autoselect (none) > > status: no carrier > > dwqe1: flags=808843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST,AUTOCONF4> mtu > > 1500 > > lladdr 3e:68:a7:8e:7e:24 > > index 2 priority 0 llprio 3 > > media: Ethernet autoselect (none) > > status: no carrier > > rge0: flags=808843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST,AUTOCONF4> mtu > > 1500 > > lladdr 3e:68:a7:8e:7e:23 > > index 3 priority 0 llprio 3 > > media: Ethernet autoselect > > status: no carrier > > rge1: flags=808843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST,AUTOCONF4> mtu > > 1500 > > lladdr 3e:68:a7:8e:7e:22 > > index 4 priority 0 llprio 3 > > groups: egress > > media: Ethernet autoselect (1000baseT full-duplex) > > status: active > > inet 192.168.1.181 netmask 0xffffff00 broadcast 192.168.1.255 > > enc0: flags=0<> > > index 5 priority 0 llprio 3 > > groups: enc > > status: active > > pflog0: flags=141<UP,RUNNING,PROMISC> mtu 33136 > > index 7 priority 0 llprio 3 > > groups: pflog > > > > --Z-- > >
