On Sat, Sep 26, 2026 at 09:32:04AM -0400, Josh Grosse wrote:
> This began at some point after the vcpu enhancement.
Adding the vm.conf. Guest is 7.9-release.
---
files= /home/josh/vm/
vm lab {
disable
owner josh
memory 8g
disk $files lab/disk.drive
disk $files lab/releases/usr.ports.drive
local interface tap0 rdomain 1 switch perm
}
switch perm {
interface veb0 rdomain 1
}
---
> # vmd -dvvvvv output, and dmesg follow.
>
> ---
>
> vmd: startup
> vmd: vm_register: registering vm 1
> vmd: /etc/vm.conf:11: vm "lab" registered (disabled)
> vmd: /etc/vm.conf:15: switch "perm" registered
> vmd: vm_priv_brconfig: interface veb0 rdomain 1
> vmd: vm_priv_brconfig: interface veb0 description switch1-perm
> vmd: vmd_configure: setting staggered start configuration to parallelism: 4
> and delay: 30
> vmd: vmd_configure: starting vms in staggered fashion
> vmd: start_vm_batch: starting batch of 4 vms
> vmd: start_vm_batch: not starting vm lab (disabled)
> vmd: start_vm_batch: done starting vms
> priv: config_getconfig: priv retrieving config
> control: config_getconfig: control retrieving config
> vmm: config_getconfig: vmm retrieving config
> agentx: config_getconfig: agentx retrieving config
> vmd: vm_opentty: vm lab tty /dev/ttyp1 uid 1000 gid 4 mode 620
> vmm: vm_register: registering vm 1
> vmd: vm_priv_ifconfig: interface tap0 description vm1-if0-lab
> vmd: vm_priv_ifconfig: switch "perm" interface veb0 add tap0
> vmd: vm_priv_ifconfig: interface tap0 rdomain 1
> vmd: vm_priv_ifconfig: interface tap0 address 100.64.1.2/31
> vmd: started lab (vm 1) successfully, tty /dev/ttyp1
> vm/lab: loadfile_bios: loaded BIOS image
> vm/lab: mmio_dev_add: added mmio handler for range [0xf0000000 - 0xffbfffff]
> vm/lab: mmio_dev_add: added mmio handler for range [0xfec00000 - 0xfec0ffff]
> vm/lab: mmio_dev_add: added mmio handler for range [0xfee00000 - 0xfee00fff]
> vm/lab: acpi_init: initializing acpi tables
> vm/lab: acpi_init: DSDT loaded successfully (523 bytes)
> vm/lab: acpi_create_facs: writing FACS to efff4000
> vm/lab: acpi_create_fadt: creating FADT
> vm/lab: acpi_create_fadt: FADT size 268
> vm/lab: acpi_create_fadt: DSDT pointer 0xefff3000 / 0x0
> vm/lab: acpi_create_fadt: writing FADT to efff2000
> vm/lab: acpi_create_fadt: FADT creation complete
> vm/lab: acpi_init: FADT created pointing to DSDT
> vm/lab: acpi_create_madt: creating MADT
> vm/lab: acpi_create_madt: MADT size 64
> vm/lab: acpi_create_madt: computed MADT checksum 0x70
> vm/lab: acpi_create_madt: writing MADT to efff1000
> vm/lab: acpi_create_madt: MADT creation complete
> vm/lab: acpi_create_xsdt: creating XSDT
> vm/lab: acpi_create_xsdt: XSDT size 52
> vm/lab: acpi_create_xsdt: writing XSDT to efff0000
> vm/lab: acpi_create_xsdt: XSDT creation complete
> vm/lab: acpi_create_rsdp: creating RSDP
> vm/lab: acpi_create_rsdp: writing RSDP to 9d000
> vm/lab: acpi_create_rsdp: RSDP creation complete
> vm/lab: acpi_init: writing RSDP pointer 0x9d00 -> 0x40e
> vm/lab: pic_set_elcr: setting level triggered mode for irq 3
> vm/lab: pic_set_elcr: setting level triggered mode for irq 5
> vm/lab: virtio_init: vm "lab" vio0 lladdr fe:e1:bb:d1:e0:2d, local
> vm/lab: pic_set_elcr: setting level triggered mode for irq 6
> vm/lab: pic_set_elcr: setting level triggered mode for irq 7
> vm/lab: lab: launching vioblk1
> priv: SIOCAIFADDR: Device busy
> vm/lab: virtio_dev_launch: sending 'd' type device struct
> vm/lab: virtio_dev_launch: sending vm message for 'lab'
> vm/lab/vioblk: vioblk_main: got viblk dev. num disk fds = 1, sync fd = 17,
> async fd = 19, capacity = 0 seg_max = 126, vm fd = 3
> vm/lab/vioblk1: vioblk_main: initialized vioblk1 with raw image
> (capacity=10485760)
> vm/lab/vioblk1: vioblk_main: wiring in async vm event handler (fd=19)
> vm/lab/vioblk1: vm_device_pipe: initializing 'd' device pipe (fd=19)
> vm/lab/vioblk1: vioblk_main: wiring in sync channel handler (fd=17)
> vm/lab/vioblk1: vioblk_main: telling vm lab device is ready
> vm/lab/vioblk1: vioblk_main: sending heartbeat
> vm/lab: virtio_dev_launch: device reports ready via sync channel
> vm/lab: vm_device_pipe: initializing 'd' device pipe (fd=18)
> vm/lab: lab: launching vioblk0
> vm/lab: virtio_dev_launch: sending 'd' type device struct
> vm/lab: virtio_dev_launch: sending vm message for 'lab'
> vm/lab/vioblk: vioblk_main: got viblk dev. num disk fds = 1, sync fd = 17,
> async fd = 20, capacity = 0 seg_max = 126, vm fd = 3
> vm/lab/vioblk0: vioblk_main: initialized vioblk0 with raw image
> (capacity=62914560)
> vm/lab/vioblk0: vioblk_main: wiring in async vm event handler (fd=20)
> vm/lab/vioblk0: vm_device_pipe: initializing 'd' device pipe (fd=20)
> vm/lab/vioblk0: vioblk_main: wiring in sync channel handler (fd=17)
> vm/lab/vioblk0: vioblk_main: telling vm lab device is ready
> vm/lab/vioblk0: vioblk_main: sending heartbeat
> vm/lab: virtio_dev_launch: device reports ready via sync channel
> vm/lab: vm_device_pipe: initializing 'd' device pipe (fd=19)
> vm/lab: lab: launching vionet0
> vm/lab: virtio_dev_launch: sending 'n' type device struct
> vm/lab: virtio_dev_launch: sending vm message for 'lab'
> vm/lab/vionet: vionet_main: got vionet dev. tap fd = 9, syncfd = 17, asyncfd
> = 21, vm fd = 3
> vm/lab/vionet0: vionet_main: wiring in async vm event handler (fd=21)
> vm/lab/vionet0: vm_device_pipe: initializing 'n' device pipe (fd=21)
> vm/lab/vionet0: vionet_main: wiring in sync channel handler (fd=17)
> vm/lab/vionet0: vionet_main: telling vm lab device is ready
> vm/lab/vionet0: vionet_main: sending async ready message
> vm/lab: virtio_dev_launch: device reports ready via sync channel
> vm/lab: vm_device_pipe: initializing 'n' device pipe (fd=20)
> vm/lab: pic_set_elcr: setting level triggered mode for irq 9
> vm/lab: run_vm: starting 1 vcpu thread(s) for vm lab
> vm/lab: vcpu_reset: resetting vcpu 0
> vm/lab: run_vm: waiting on events for VM lab
> vm/lab: lab: received tap addr fe:e1:ba:d3:49:aa for nic 0
> vm/lab: handle_dev_msg: device reports ready
> vm/lab: handle_dev_msg: device reports ready
> vm/lab: handle_dev_msg: device reports ready
> vm/lab/vionet0: dev_dispatch_vm: set hostmac
> vm/lab: vcpu_exit_fw_cfg: selector 0x0000
> vm/lab: vcpu_exit_fw_cfg: selector 0x0001
> vm/lab: fw_cfg_handle_dma: selector 0x0019
> vm/lab: fw_cfg_file_dir: file directory with 4 files
> vm/lab: 36B 0020 etc/acpi/rsdp
> vm/lab: 128B 0021 etc/table-loader
> vm/lab: 120B 0022 etc/e820
> vm/lab: 4B 0023 etc/screen-and-debug
> vm/lab: vcpu_exit_fw_cfg: selector 0x0022
> vm/lab: fw_cfg_select_file: accessing file etc/e820
> vm/lab: fw_cfg_handle_dma: selector 0x000d
> vm/lab: fw_cfg_select: unhandled selector d
> vm/lab: fw_cfg_handle_dma: selector 0x000f
> vm/lab: fw_cfg_handle_dma: selector 0x8000
> vm/lab: fw_cfg_select: unhandled selector 8000
> vm/lab: fw_cfg_handle_dma: selector 0x8001
> vm/lab: fw_cfg_select: unhandled selector 8001
> vm/lab: fw_cfg_handle_dma: selector 0x0019
> vm/lab: fw_cfg_file_dir: file directory with 4 files
> vm/lab: 36B 0020 etc/acpi/rsdp
> vm/lab: 128B 0021 etc/table-loader
> vm/lab: 120B 0022 etc/e820
> vm/lab: 4B 0023 etc/screen-and-debug
> vm/lab: fw_cfg_handle_dma: selector 0x0004
> vm/lab: i8259_write_datareg: master pic, reset IRQ vector to 0x8
> vm/lab: i8259_write_datareg: slave pic, reset IRQ vector to 0x70
> vm/lab: fw_cfg_handle_dma: selector 0x000f
> vm/lab: fw_cfg_handle_dma: selector 0x0005
> vm/lab: translate_gva: unpaged, va=pa=0xf600f
> vm/lab: translate_gva: unpaged, va=pa=0xf6017
> vm/lab: translate_gva: unpaged, va=pa=0xf601c
> vm/lab: translate_gva: unpaged, va=pa=0xf6026
> vm/lab: translate_gva: unpaged, va=pa=0xf603a
> vm/lab: translate_gva: unpaged, va=pa=0xf6044
> vm/lab: fw_cfg_handle_dma: selector 0x0005
> vm/lab: fw_cfg_handle_dma: selector 0x0021
> vm/lab: fw_cfg_select_file: accessing file etc/table-loader
> vm/lab: fw_cfg_handle_dma: selector 0x0020
> vm/lab: fw_cfg_select_file: accessing file etc/acpi/rsdp
> vm/lab: fw_cfg_handle_dma: selector 0x0023
> vm/lab: fw_cfg_select_file: accessing file etc/screen-and-debug
> vm/lab: vcpu_process_com_lcr: set baudrate = 115200
> vm/lab: vcpu_process_com_lcr: set baudrate = 115200
> vm/lab: vcpu_process_com_lcr: set baudrate = 115200
> vmd: vmd_dispatch_vmm: running vm: 1, vm_state: 0x3
> vm/lab: i8259_write_datareg: master pic, reset IRQ vector to 0x20
> vm/lab: i8259_write_datareg: slave pic, reset IRQ vector to 0x28
> vmd: vmd_dispatch_vmm: running vm: 1, vm_state: 0x3
> vm/lab: vcpu_process_com_lcr: set baudrate = 115200
> vmd: vmd_dispatch_vmm: running vm: 1, vm_state: 0x3
> vmd: vmd_dispatch_vmm: running vm: 1, vm_state: 0x3
> vm/lab: vcpu_process_com_lcr: set baudrate = 115200
> vmd: vmd_dispatch_vmm: running vm: 1, vm_state: 0x3
> vmd: vmd_dispatch_vmm: running vm: 1, vm_state: 0x3
> vmd: vmd_dispatch_vmm: running vm: 1, vm_state: 0x3
> vm/lab: vcpu_exit_eptviolation: instruction might cross page boundary
> vm/lab: virtio_shutdown: waiting on device pid 50277
> vm/lab/vionet0: rx_run_loop: exiting (0)
> vm/lab/vionet0: tx_run_loop: exiting (0)
> vm/lab: virtio_shutdown: device for pid 50277 is stopped
> vm/lab: virtio_shutdown: waiting on device pid 78826
> vm/lab: virtio_shutdown: device for pid 78826 is stopped
> vm/lab: virtio_shutdown: waiting on device pid 7508
> vm/lab: virtio_shutdown: device for pid 7508 is stopped
> vmm: vmm_sighdlr: handling signal 20
> vmm: vmm_sighdlr: vm lab exited (id 1)
> vmm: vm_remove: vmm vmm_sighdlr removing vm 1 from running config
> vmm: vm_stop: vmm vmm_sighdlr stopping vm 1
> vmd: vm_stop: vmd vmd_dispatch_vmm stopping vm 1
> vmd: vmd_dispatch_vmm: vm: 1, vm_state: 0x2
> vmd: vmd_sighdlr: handling signal
> vmd: vmd_shutdown: performing shutdown
> vmd: vm_remove: vmd vmd_shutdown removing vm 1 from running config
> vmm: vmm exiting, pid 24049
> vmd: vm_stop: vmd vmd_shutdown stopping vm 1
> priv: priv exiting, pid 94500
> control: control exiting, pid 42958
> agentx: agentx exiting, pid 130
> vmd: terminating
>
> ---
>
> OpenBSD 8.0-beta (GENERIC.MP) #57: Sat Sep 26 00:32:32 MDT 2026
> [email protected]:/usr/src/sys/arch/amd64/compile/GENERIC.MP
> real mem = 17034862592 (16245MB)
> avail mem = 16494858240 (15730MB)
> random: good seed from bootblocks
> mpath0 at root
> scsibus0 at mpath0: 256 targets
> mainbus0 at root
> bios0 at mainbus0: SMBIOS rev. 2.7 @ 0xbcd2d000 (66 entries)
> bios0: vendor LENOVO version "GMET91WW (2.39 )" date 06/03/2021
> bios0: LENOVO 20BE00BTUS
> efi0 at bios0: UEFI 2.3.1
> efi0: Lenovo rev 0x2390
> acpi0 at bios0: ACPI 5.0
> acpi0: sleep states S0 S3 S4 S5
> acpi0: tables DSDT FACP SLIC DBGP ECDT HPET APIC MCFG SSDT SSDT SSDT SSDT
> SSDT SSDT SSDT PCCT SSDT TCPA UEFI MSDM ASF! BATB FPDT UEFI BGRT
> acpi0: wakeup devices LID_(S4) SLPB(S3) IGBE(S4) EXP2(S4) EXP3(S4) XHCI(S3)
> EHC1(S3) EHC2(S3)
> acpitimer0 at acpi0: 3579545 Hz, 24 bits
> acpiec0 at acpi0
> acpihpet0 at acpi0: 14318179 Hz
> acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
> cpu0 at mainbus0: apid 0 (boot processor)
> cpu0: Intel(R) Core(TM) i5-4210M CPU @ 2.60GHz, 2594.03 MHz, 06-3c-03, patch
> 00000028
> cpu0: cpuid 1
> edx=bfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
>
> ecx=77dafbbf<SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,FMA3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,MOVBE,POPCNT,DEADLINE,AES,XSAVE,AVX,F16C,RDRAND>
> cpu0: cpuid 6 eax=77<SENSOR,ARAT,PTS> ecx=9<EFFFREQ>
> cpu0: cpuid 7.0
> ebx=27ab<FSGSBASE,TSC_ADJUST,BMI1,AVX2,SMEP,BMI2,ERMS,INVPCID>
> edx=9c000600<SRBDS_CTRL,MD_CLEAR,IBRS,IBPB,STIBP,L1DF,SSBD>
> cpu0: cpuid a vers=3, gp=4, gpwidth=48, ff=3, ffwidth=48
> cpu0: cpuid d.1 eax=1<XSAVEOPT>
> cpu0: cpuid 80000001 edx=2c100800<NXE,PAGE1GB,RDTSCP,LONG> ecx=21<LAHF,ABM>
> cpu0: cpuid 80000007 edx=100<ITSC>
> cpu0: MELTDOWN
> cpu0: 32KB 64b/line 8-way D-cache, 32KB 64b/line 8-way I-cache, 256KB
> 64b/line 8-way L2 cache, 3MB 64b/line 12-way L3 cache
> cpu0: smt 0, core 0, package 0, type P
> mtrr: Pentium Pro MTRR support, 10 var ranges, 88 fixed ranges
> cpu0: apic clock running at 99MHz
> cpu0: mwait min=64, max=64, C-substates=0.2.1.2.4, IBE
> cpu1 at mainbus0: apid 1 (application processor)
> cpu1: Intel(R) Core(TM) i5-4210M CPU @ 2.60GHz, 2594.02 MHz, 06-3c-03, patch
> 00000028
> cpu1: smt 1, core 0, package 0, type SP
> cpu2 at mainbus0: apid 2 (application processor)
> cpu2: Intel(R) Core(TM) i5-4210M CPU @ 2.60GHz, 2594.03 MHz, 06-3c-03, patch
> 00000028
> cpu2: smt 0, core 1, package 0, type P
> cpu3 at mainbus0: apid 3 (application processor)
> cpu3: Intel(R) Core(TM) i5-4210M CPU @ 2.60GHz, 2594.08 MHz, 06-3c-03, patch
> 00000028
> cpu3: smt 1, core 1, package 0, type SP
> ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins
> acpimcfg0 at acpi0
> acpimcfg0: addr 0xf8000000, bus 0-63
> acpiprt0 at acpi0: bus 0 (PCI0)
> acpiprt1 at acpi0: bus -1 (PEG_)
> acpiprt2 at acpi0: bus 3 (EXP1)
> acpiprt3 at acpi0: bus 4 (EXP2)
> acpiprt4 at acpi0: bus 5 (EXP3)
> acpiprt5 at acpi0: bus -1 (EXP6)
> acpibtn0 at acpi0: LID_(wakeup)
> acpibtn1 at acpi0: SLPB(wakeup)
> acpipci0 at acpi0 PCI0: 0x00000000 0x00000011 0x00000001
> acpicmos0 at acpi0
> "LEN0071" at acpi0 not configured
> "LEN0034" at acpi0 not configured
> tpm0 at acpi0 TPM_ 1.2 (TIS) addr 0xfed40000/0x5000, device 0x0000104a rev
> 0x4e
> acpibat0 at acpi0: BAT0 model "45N1769" serial 3053 type LION oem "SANYO"
> acpiac0 at acpi0: AC unit online
> acpithinkpad0 at acpi0: version 1.0
> "PNP0C14" at acpi0 not configured
> "PNP0C14" at acpi0 not configured
> "PNP0C14" at acpi0 not configured
> "INT340F" at acpi0 not configured
> acpicpu0 at acpi0: C2(200@148 mwait.1@0x33), C1(1000@1 mwait.1), PSS
> acpicpu1 at acpi0: C2(200@148 mwait.1@0x33), C1(1000@1 mwait.1), PSS
> acpicpu2 at acpi0: C2(200@148 mwait.1@0x33), C1(1000@1 mwait.1), PSS
> acpicpu3 at acpi0: C2(200@148 mwait.1@0x33), C1(1000@1 mwait.1), PSS
> acpipwrres0 at acpi0: PUBS, resource for XHCI, EHC1, EHC2
> acpipwrres1 at acpi0: NVP3, resource for PEG_
> acpipwrres2 at acpi0: NVP2, resource for PEG_
> acpitz0 at acpi0
> acpitz0: critical temperature is 200 degC
> acpivideo0 at acpi0: VID_
> acpivout0 at acpivideo0: LCD0
> acpivideo1 at acpi0: VID_
> cpu0: using VERW MDS workaround (except on vmm entry)
> cpu0: Enhanced SpeedStep 2594 MHz: speeds: 2601, 2600, 2500, 2300, 2200,
> 2100, 2000, 1800, 1700, 1600, 1400, 1300, 1200, 1100, 900, 800 MHz
> pci0 at mainbus0 bus 0
> pchb0 at pci0 dev 0 function 0 "Intel Core 4G Host" rev 0x06
> inteldrm0 at pci0 dev 2 function 0 "Intel HD Graphics 4600" rev 0x06
> drm0 at inteldrm0
> inteldrm0: msi, HASWELL, gen 7
> azalia0 at pci0 dev 3 function 0 "Intel Core 4G HD Audio" rev 0x06: msi
> azalia0: No codecs found
> xhci0 at pci0 dev 20 function 0 "Intel 8 Series xHCI" rev 0x04: msi, xHCI 1.0
> usb0 at xhci0: USB revision 3.0
> uhub0 at usb0 configuration 1 interface 0 "Intel xHCI root hub" rev 3.00/1.00
> addr 1
> "Intel 8 Series MEI" rev 0x04 at pci0 dev 22 function 0 not configured
> em0 at pci0 dev 25 function 0 "Intel I217-LM" rev 0x04: msi, address
> 54:ee:75:63:2d:55
> ehci0 at pci0 dev 26 function 0 "Intel 8 Series USB" rev 0x04: apic 2 int 16
> usb1 at ehci0: USB revision 2.0
> uhub1 at usb1 configuration 1 interface 0 "Intel EHCI root hub" rev 2.00/1.00
> addr 1
> azalia1 at pci0 dev 27 function 0 "Intel 8 Series HD Audio" rev 0x04: msi
> azalia1: codecs: Realtek ALC292
> audio0 at azalia1
> ppb0 at pci0 dev 28 function 0 "Intel 8 Series PCIE" rev 0xd4: msi
> pci1 at ppb0 bus 3
> rtsx0 at pci1 dev 0 function 0 "Realtek RTS5227 Card Reader" rev 0x01: msi
> sdmmc0 at rtsx0: 4-bit, dma
> ppb1 at pci0 dev 28 function 1 "Intel 8 Series PCIE" rev 0xd4: msi
> pci2 at ppb1 bus 4
> iwm0 at pci2 dev 0 function 0 "Intel AC 7260" rev 0x6b, msi
> ppb2 at pci0 dev 28 function 2 "Intel 8 Series PCIE" rev 0xd4: msi
> pci3 at ppb2 bus 5
> ehci1 at pci0 dev 29 function 0 "Intel 8 Series USB" rev 0x04: apic 2 int 23
> usb2 at ehci1: USB revision 2.0
> uhub2 at usb2 configuration 1 interface 0 "Intel EHCI root hub" rev 2.00/1.00
> addr 1
> pcib0 at pci0 dev 31 function 0 "Intel QM87 LPC" rev 0x04
> ahci0 at pci0 dev 31 function 2 "Intel 8 Series AHCI" rev 0x04: msi, AHCI 1.3
> ahci0: port 0: 6.0Gb/s
> ahci0: port 5: 1.5Gb/s
> scsibus1 at ahci0: 32 targets
> sd0 at scsibus1 targ 0 lun 0: <ATA, SAMSUNG MZ7LN512, MVT0>
> naa.5002538d005dbce6
> sd0: 488386MB, 512 bytes/sector, 1000215216 sectors, thin
> cd0 at scsibus1 targ 5 lun 0: <MATSHITA, DVD-RAM UJ8G2, 1.00> removable
> ichiic0 at pci0 dev 31 function 3 "Intel 8 Series SMBus" rev 0x04: apic 2 int
> 18
> iic0 at ichiic0
> isa0 at pcib0
> isadma0 at isa0
> pckbc0 at isa0 port 0x60/5 irq 1 irq 12
> pckbd0 at pckbc0 (kbd slot)
> wskbd0 at pckbd0: console keyboard
> pms0 at pckbc0 (aux slot)
> wsmouse0 at pms0 mux 0
> wsmouse1 at pms0 mux 0
> pms0: Synaptics clickpad, firmware 8.1, 0x1e2b1 0x940300 0x2d9440 0xd001a3
> 0x12f800
> pcppi0 at isa0 port 0x61
> spkr0 at pcppi0
> vmm0 at mainbus0: VMX/EPT
> efifb at mainbus0 not configured
> iwm0: restrict all mbufs to low memory
> uvideo0 at uhub0 port 12 configuration 1 interface 0 "SunplusIT INC.
> Integrated Camera" rev 2.00/26.03 addr 2
> video0 at uvideo0
> uhub3 at uhub1 port 1 configuration 1 interface 0 "Intel Rate Matching Hub"
> rev 2.00/0.04 addr 2
> uhub4 at uhub2 port 1 configuration 1 interface 0 "Intel Rate Matching Hub"
> rev 2.00/0.04 addr 2
> sdmmc0: can't enable card
> vscsi0 at root
> scsibus2 at vscsi0: 256 targets
> softraid0 at root
> scsibus3 at softraid0: 256 targets
> sd1 at scsibus3 targ 1 lun 0: <OPENBSD, SR CRYPTO, 006>
> sd1: 488126MB, 512 bytes/sector, 999682111 sectors
> root on sd1a (ff46b9ed41b27d65.a) swap on sd1b dump on sd1b
> inteldrm0: 1366x768, 32bpp
> wsdisplay0 at inteldrm0 mux 1: console (std, vt100 emulation), using wskbd0
> wsdisplay0: screen 1-5 added (std, vt100 emulation)
> iwm0: hw rev 0x140, fw ver 17.3216344376.0, address cc:3d:82:8a:6e:25
