I see this on at least one router in every IPX lab I do using proctorlabs. DLCI missing on at least one point-to-point subint... I'm not entirely sure which exact labs I've seen it on but at least on all the QoS and MPLS related labs. I did those today so it's fresh in my memory.
I've also seen it on at least 3+ different pods. On Sun, Oct 24, 2010 at 1:15 AM, Amer Mustafa <[email protected]> wrote: > Steve / IP EXPERT team. > > Yup, again the same issue between the R2 and R5 FR clould, no Interface-dlci > on R2 and the interface was also down. > > > Regards ... > > On Sun, Oct 24, 2010 at 1:30 AM, Di Bias, Steve <[email protected]> > wrote: >> >> OK sorry, I didn’t realize you were in the proctorlabs environment. If >> you don’t hear back from Marko or Tyson I would notify support on this >> because it can take away valuable lab time!! >> >> >> >> From: Amer Mustafa [mailto:[email protected]] >> Sent: Saturday, October 23, 2010 3:28 PM >> To: Di Bias, Steve >> Cc: [email protected] >> Subject: Re: [OSL | CCIE_RS] Workbook 1 LAB 18. >> >> >> >> Steve, >> >> >> >> They were down because there was no DLCI assigned in the sub-interfaces ( >> all routes ), You are right with the config below, this is exact same >> avilable on ipexpert site for manual configuration on the routers. >> >> >> >> But i guess when you load the configs through script on proctorlabs they >> come up without frame-relay interface-dlci assigned. >> >> >> >> >> >> regards ... >> >> Amer >> >> >> >> On Sun, Oct 24, 2010 at 1:20 AM, Di Bias, Steve <[email protected]> >> wrote: >> >> Can you be more specific? Why were they “down”? There was no DLCI’s >> configured? The wrong DLCI’s were configured? The wrong LMI type? >> >> >> >> I just looked at the initials configs for VOL1 LAB18 and everything is >> configured just fine >> >> >> >> R2 >> >> >> >> interface Serial0/1/0 >> >> no ip address >> >> encapsulation frame-relay >> >> no arp frame-relay >> >> no frame-relay inverse-arp >> >> frame-relay lmi-type cisco >> >> no shutdown >> >> ! >> >> interface Serial0/1/0.24 point-to-point >> >> ip address 150.50.24.2 255.255.255.252 >> >> frame-relay interface-dlci 204 >> >> ! >> >> interface Serial0/1/0.25 point-to-point >> >> ip address 150.50.25.2 255.255.255.252 >> >> frame-relay interface-dlci 205 >> >> ! >> >> interface Serial0/1/0.26 point-to-point >> >> ip address 150.50.26.2 255.255.255.252 >> >> frame-relay interface-dlci 206 >> >> >> >> R4 >> >> >> >> interface Serial0/0/0 >> >> no ip address >> >> encapsulation frame-relay >> >> no arp frame-relay >> >> no frame-relay inverse-arp >> >> frame-relay lmi-type cisco >> >> no shutdown >> >> ! >> >> interface Serial0/0/0.24 point-to-point >> >> ip address 150.50.24.1 255.255.255.252 >> >> frame-relay interface-dlci 402 >> >> >> >> R5 >> >> >> >> interface Serial0/1/0 >> >> no ip address >> >> encapsulation frame-relay >> >> no arp frame-relay >> >> no frame-relay inverse-arp >> >> frame-relay lmi-type cisco >> >> no shutdown >> >> ! >> >> interface Serial0/1/0.25 point-to-point >> >> ip address 150.50.25.1 255.255.255.252 >> >> frame-relay interface-dlci 502 >> >> >> >> R6 >> >> >> >> interface Serial0/1/0 >> >> no ip address >> >> encapsulation frame-relay >> >> serial restart-delay 0 >> >> no arp frame-relay >> >> no frame-relay inverse-arp >> >> frame-relay lmi-type cisco >> >> no shutdown >> >> ! >> >> interface Serial0/1/0.26 point-to-point >> >> ip address 150.50.26.1 255.255.255.252 >> >> frame-relay interface-dlci 602 >> >> >> >> >> >> >> >> >> >> >> >> From: [email protected] >> [mailto:[email protected]] On Behalf Of Amer Mustafa >> Sent: Saturday, October 23, 2010 3:10 PM >> To: [email protected] >> Subject: [OSL | CCIE_RS] Workbook 1 LAB 18. >> >> >> >> Workbook 1 LAB 18. >> >> >> >> The inital configs of the routers are with FR proper config, which leads >> that the FR links are down. i had to configure ( Frame-relay interface DLCI >> ) on all the routers. just would like to know if this is not avilable in the >> initial configs on purpose ? becuase its not mentioned in the lab to check >> FR links or verify them. >> >> >> >> >> >> thanks >> >> amer >> >> >> UHS Confidentiality Notice: This e-mail message, including any >> attachments, is for the sole use of the intended recipient(s) and may >> contain confidential and privileged information. Any unauthorized review, >> use, disclosure or distribution of this information is prohibited, and may >> be punishable by law. If this was sent to you in error, please notify the >> sender by reply e-mail and destroy all copies of the original message. >> >> >> >> >> UHS Confidentiality Notice: This e-mail message, including any >> attachments, is for the sole use of the intended recipient(s) and may >> contain confidential and privileged information. Any unauthorized review, >> use, disclosure or distribution of this information is prohibited, and may >> be punishable by law. If this was sent to you in error, please notify the >> sender by reply e-mail and destroy all copies of the original message. > > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
