Hi.
I'm currently experiencing a connectivity problem between a 7609 and a
3560, which so matters for my current job position.
There is Mikrotik rb1200 RouterBoard between these to which two of its
ports are connected to the Router and Switch and I've made them bridge. I
use this Mikrotik Device as a Bandwidth Shaper.
When the 7609 and the 3560 are DIRECTLY connected, 7609 G5/2 <-> 3560
G0/22, there is no problem!
But when the Mikrotik is inserted between, for a while everything is OK,
but accidentals the connectivity is lost, but after a while again it
changes to OK.
Mikrotik ETH1 is connected to the 7609 G5/2 and is 1Gb and full-duplex as
ETH2 which is connected to the 3560 G5/22, and both are mapped to bridge1.
7609Router# sh ver
c7600rsp72043_rp Software (c7600rsp72043_rp-ADVENTERPRISEK9-M), Version
15.1(3)S, RELEASE SOFTWARE (fc1)
Cisco CISCO7609-S (M8500) processor (revision 1.0) with 917504K/65536K
bytes of memory.
Processor board ID FOX1442H66G
BASEBOARD: RSP720
CPU: MPC8548_E, Version: 2.0, (0x80390020)
CORE: E500, Version: 2.0, (0x80210020)
CPU:1200MHz, CCB:400MHz, DDR:200MHz,
L1: D-cache 32 kB enabled
I-cache 32 kB enabled
Last reset from power-on
1 SIP-400 controller (5 GigabitEthernet)(4 POS).
1 Virtual Ethernet interface
7 Gigabit Ethernet interfaces
4 Packet over SONET interfaces
3964K bytes of non-volatile configuration memory.
507024K bytes of Internal ATA PCMCIA card (Sector size 512 bytes).
Configuration register is 0x2102
!
7609Router#sr int g5/2
Building configuration...
Current configuration : 241 bytes
!
interface GigabitEthernet5/2
description Connected to Core Switch
ip address 192.168.1.1 255.255.255.252
ip ospf network point-to-point
ip ospf dead-interval 20
ip ospf hello-interval 2
no mdix auto
service-policy output SHAPE
!
7609Router#sh inter g5/2
GigabitEthernet5/2 is up, line protocol is up (connected)
Hardware is C7600 1Gb 802.3, address is 588d.0912.6d80 (bia
588d.0912.6d80)
Description: Connected to Core Switch
Internet address is 192.168.1.1/30
MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 6/255, rxload 8/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 1000Mb/s, media type is T
Media-type configured as SFP connector
input flow-control is off, output flow-control is off
Clock mode is auto
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 31810000 bits/sec, 30156 packets/sec
5 minute output rate 27354000 bits/sec, 6659 packets/sec
L2 Switched: ucast: 11490123 pkt, 1089129555 bytes - mcast: 601337 pkt,
64168604 bytes
L3 in Switched: ucast: 9808379794 pkt, 3373019223246 bytes - mcast: 0
pkt, 0 bytes mcast
L3 out Switched: ucast: 9861630782 pkt, 5796605234022 bytes mcast: 0 pkt,
0 bytes
9841352782 packets input, 3375755871116 bytes, 0 no buffer
Received 662805 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
9879380703 packets output, 5812334751940 bytes, 0 underruns
0 output errors, 0 collisions, 5 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
!
7609Router#sh mod all
Mod Ports Card Type Model Serial
No.
--- ----- -------------------------------------- ------------------
-----------
5 2 Route Switch Processor 720 (Active) RSP720-3C-GE
JAE1224LBQV
8 0 4-subslot SPA Interface Processor-400 7600-SIP-400
JAE1125MAUY
Mod MAC addresses Hw Fw Sw
Status
--- ---------------------------------- ----- ------------- ------------
-------
5 001d.4558.fb9c to 001d.4558.fb9f 5.2 12.2(33r)SRD 15.1(3) Ok
8 001b.53cc.d040 to 001b.53cc.d0bf 2.4 15.1(3)S 15.1(3)S Ok
Mod Sub-Module Model Serial Hw
Status
---- --------------------------- ------------------ ----------- -------
-------
5 Policy Feature Card 3 7600-PFC3C JAE1224LAJO 1.1 Ok
5 C7600 MSFC4 Daughterboard 7600-MSFC4 JAE1224L2FO 1.1 Ok
8/0 5xGE SPA SPA-5X1GE-V2 JAE141003QJ 1.2 Ok
8/1 4xOC3 POS SPA SPA-4XOC3-POS JAE12046H75 1.0 Ok
Mod Online Diag Status
---- -------------------
5 Pass
8 Pass
8/0 Pass
8/1 Pass
!
7609Router#sh diagbus
Slot 8: Logical_index 16
4-subslot SPA Interface Processor-400 controller
Board is analyzed ipc ready
HW rev 2.4, board revision C0
Serial Number: JAE1125MAUY Part number: 73-8404-14
Slot database information:
Flags: 0x2004 Insertion time: 0x1C81C (1w6d ago)
Controller Memory Size:
992 MBytes CPU Memory
31 MBytes Packet Memory
1023 MBytes Total on Board SDRAM
Cisco IOS Software, cwlc Software (sip2-DW-M), Version 15.1(3)S,
RELEASE SOFTWARE (fc1)
SPA Information:
subslot 8/0: SPA-5X1GE-V2 (0x50A), status: ok
subslot 8/1: SPA-4XOC3-POS (0x440), status: ok
!
7609Router# sh diagnostic result all detail
Current bootup diagnostic level: minimal
Module 5: Route Switch Processor 720 (Active) SerialNo : JAE1224LBQV
Overall Diagnostic Result for Module 5 : PASS
Diagnostic level at card bootup: minimal
Test results: (. = Pass, F = Fail, U = Untested)
___________________________________________________________________________
1) TestScratchRegister -------------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 34753
Last test testing type ------> Health Monitoring
Last test execution time ----> Nov 21 2011 20:04:02
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Nov 21 2011 20:04:02
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________________
2) TestSPRPInbandPing --------------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 69506
Last test testing type ------> Health Monitoring
Last test execution time ----> Nov 21 2011 20:04:05
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Nov 21 2011 20:04:05
Total failure count ---------> 0
Consecutive failure count ---> 0
CPU util(5sec) SP -----------> 9%
CPU util(5sec) RP -----------> 2%
Traffic ---------------------> 0%
netint_thr_active -----------> 0
Inband Tx_Rate --------------> 1266
Inband Rx_Rate --------------> 26
Per-device Failure Count ----> n/a
___________________________________________________________________________
3) TestTransceiverIntegrity:
Port 1 2
----------
. .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 23
Last test testing type ------> OnDemand
Last test execution time ----> Nov 09 2011 15:24:50
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Nov 09 2011 15:24:50
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________________
4) TestActiveToStandbyLoopback:
Port 1 2
----------
U U
Error code ------------------> 3 (DIAG_SKIPPED)
Total run count -------------> 0
Last test testing type ------> n/a
Last test execution time ----> n/a
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> n/a
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________________
5) TestLoopback:
Port 1 2
----------
. .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Bootup
Last test execution time ----> Nov 08 2011 18:14:21
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Nov 08 2011 18:14:21
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________________
6) TestNewIndexLearn ---------------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Bootup
Last test execution time ----> Nov 08 2011 18:14:22
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Nov 08 2011 18:14:22
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________________
7) TestDontConditionalLearn --------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Bootup
Last test execution time ----> Nov 08 2011 18:14:22
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Nov 08 2011 18:14:22
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________________
8) TestBadBpduTrap -----------------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Bootup
Last test execution time ----> Nov 08 2011 18:14:22
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Nov 08 2011 18:14:22
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________________
9) TestMatchCapture ----------------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Bootup
Last test execution time ----> Nov 08 2011 18:14:23
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Nov 08 2011 18:14:23
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________________
10) TestProtocolMatchChannel --------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Bootup
Last test execution time ----> Nov 08 2011 18:14:24
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Nov 08 2011 18:14:24
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________________
11) TestFibDevices ------------------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Bootup
Last test execution time ----> Nov 08 2011 18:14:25
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Nov 08 2011 18:14:25
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________________
12) TestIPv4FibShortcut -------------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Bootup
Last test execution time ----> Nov 08 2011 18:14:25
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Nov 08 2011 18:14:25
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________________
13) TestL3Capture2 ------------------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Bootup
Last test execution time ----> Nov 08 2011 18:14:25
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Nov 08 2011 18:14:25
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________________
14) TestIPv6FibShortcut -------------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Bootup
Last test execution time ----> Nov 08 2011 18:14:26
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Nov 08 2011 18:14:26
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________________
15) TestMPLSFibShortcut -------------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Bootup
Last test execution time ----> Nov 08 2011 18:14:26
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Nov 08 2011 18:14:26
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________________
16) TestNATFibShortcut --------------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Bootup
Last test execution time ----> Nov 08 2011 18:14:26
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Nov 08 2011 18:14:26
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________________
17) TestAclPermit -------------------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Bootup
Last test execution time ----> Nov 08 2011 18:14:26
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Nov 08 2011 18:14:26
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________________
18) TestQoSTcam ---------------------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Bootup
Last test execution time ----> Nov 08 2011 18:14:27
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Nov 08 2011 18:14:27
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________________
19) TestL3VlanMet -------------------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Bootup
Last test execution time ----> Nov 08 2011 18:14:27
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Nov 08 2011 18:14:27
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________________
20) TestIngressSpan -----------------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Bootup
Last test execution time ----> Nov 08 2011 18:14:27
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Nov 08 2011 18:14:27
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________________
21) TestEgressSpan ------------------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Bootup
Last test execution time ----> Nov 08 2011 18:14:27
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Nov 08 2011 18:14:27
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________________
22) TestNetflowInlineRewrite:
Port 1 2
----------
U U
Error code ------------------> 3 (DIAG_SKIPPED)
Total run count -------------> 0
Last test testing type ------> n/a
Last test execution time ----> n/a
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> n/a
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________________
23) TestFabricSnakeForward ----------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Bootup
Last test execution time ----> Nov 08 2011 18:14:27
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Nov 08 2011 18:14:27
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________________
24) TestFabricSnakeBackward ---------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Bootup
Last test execution time ----> Nov 08 2011 18:14:27
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Nov 08 2011 18:14:27
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________________
25) TestTrafficStress ---------------> U
Error code ------------------> 3 (DIAG_SKIPPED)
Total run count -------------> 0
Last test testing type ------> n/a
Last test execution time ----> n/a
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> n/a
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________________
26) TestFibTcamSSRAM ----------------> U
Error code ------------------> 3 (DIAG_SKIPPED)
Total run count -------------> 0
Last test testing type ------> n/a
Last test execution time ----> n/a
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> n/a
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________________
27) TestAsicMemory ------------------> U
Error code ------------------> 3 (DIAG_SKIPPED)
Total run count -------------> 0
Last test testing type ------> n/a
Last test execution time ----> n/a
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> n/a
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________________
28) TestAclQosTcam ------------------> U
Error code ------------------> 3 (DIAG_SKIPPED)
Total run count -------------> 0
Last test testing type ------> n/a
Last test execution time ----> n/a
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> n/a
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________________
29) TestNetflowTcam -----------------> U
Error code ------------------> 3 (DIAG_SKIPPED)
Total run count -------------> 0
Last test testing type ------> n/a
Last test execution time ----> n/a
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> n/a
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________________
30) ScheduleSwitchover --------------> U
Error code ------------------> 3 (DIAG_SKIPPED)
Total run count -------------> 0
Last test testing type ------> n/a
Last test execution time ----> n/a
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> n/a
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________________
31) FirmwareDiagStatus --------------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Bootup
Last test execution time ----> Nov 08 2011 18:14:28
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Nov 08 2011 18:14:28
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________________
32) TestFabricFlowControlStatus -----> U
Error code ------------------> 3 (DIAG_SKIPPED)
Total run count -------------> 0
Last test testing type ------> n/a
Last test execution time ----> n/a
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> n/a
Total failure count ---------> 0
Consecutive failure count ---> 0
Current run count -------------------------->: 0
First test execution time ------------------>:
Last test execution time ------------------->:
Total FPOE Rate0 Count --------------------->: 0
Total FPOE Reduced Rate Count -------------->: 0
___________________________________________________________________________
33) TestErrorCounterMonitor ---------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 34753
Last test testing type ------> Health Monitoring
Last test execution time ----> Nov 21 2011 20:04:05
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Nov 21 2011 20:04:05
Total failure count ---------> 0
Consecutive failure count ---> 0
Error Records ---------------> n/a
___________________________________________________________________________
Module 8: 4-subslot SPA Interface Processor-400 SerialNo : JAE1125MAUY
Overall Diagnostic Result for Module 8 : PASS
Diagnostic level at card bootup: minimal
Test results: (. = Pass, F = Fail, U = Untested)
___________________________________________________________________________
1) BusConnectivityTest -------------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 486479
Last test testing type ------> Health Monitoring
Last test execution time ----> Nov 21 2011 20:04:16
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Nov 21 2011 20:04:16
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________________
2) TestEobcStressPing --------------> U
Error code ------------------> 3 (DIAG_SKIPPED)
Total run count -------------> 0
Last test testing type ------> n/a
Last test execution time ----> n/a
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> n/a
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________________
3) TestFirmwareDiagStatus ----------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Bootup
Last test execution time ----> Nov 08 2011 18:15:24
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Nov 08 2011 18:15:24
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________________
Module 8/0: 5xGE SPA SerialNo : JAE141003QJ SerialNo :
JAE1125MAUY
Overall Diagnostic Result for Module 8/0 : PASS
Diagnostic level at card bootup: minimal
Test results: (. = Pass, F = Fail, U = Untested)
___________________________________________________________________
1) TestSpaScratchRegister ----------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Bootup
Last test execution time ----> Nov 08 2011 18:15:29
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Nov 08 2011 18:15:29
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________
2) PortLoopbackTest:
Port 1 2 3 4 5
-------------------
U U U U U
Error code ------------------> 3 (DIAG_SKIPPED)
Total run count -------------> 0
Last test testing type ------> n/a
Last test execution time ----> n/a
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> n/a
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________
Module 8/1: 4xOC3 POS SPA SerialNo : JAE12046H75 SerialNo :
JAE1125MAUY
Overall Diagnostic Result for Module 8/1 : PASS
Diagnostic level at card bootup: minimal
Test results: (. = Pass, F = Fail, U = Untested)
___________________________________________________________________
1) TestSpaScratchRegister ----------> .
Error code ------------------> 0 (DIAG_SUCCESS)
Total run count -------------> 1
Last test testing type ------> Bootup
Last test execution time ----> Nov 08 2011 18:15:30
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> Nov 08 2011 18:15:30
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________
2) PortLoopbackTest:
Port 1 2 3 4
----------------
U U U U
Error code ------------------> 3 (DIAG_SKIPPED)
Total run count -------------> 0
Last test testing type ------> n/a
Last test execution time ----> n/a
First test failure time -----> n/a
Last test failure time ------> n/a
Last test pass time ---------> n/a
Total failure count ---------> 0
Consecutive failure count ---> 0
___________________________________________________________________
!
======================================
3560Switch#sh ver
C3560 Software (C3560-IPSERVICESK9-M), Version 15.0(1)SE, RELEASE SOFTWARE
(fc1)
cisco WS-C3560G-24TS (PowerPC405) processor (revision F0) with 131072K
bytes of memory.
Processor board ID FOC1518Y4VP
Last reset from power-on
3 Virtual Ethernet interfaces
28 Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.
512K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address : E8:BA:70:EB:A6:80
Motherboard assembly number : 73-10215-06
Power supply part number : 341-0098-02
Motherboard serial number : FOC151805NM
Power supply serial number : AZS15180166
Model revision number : F0
Motherboard revision number : A0
Model number : WS-C3560G-24TS-S
System serial number : FOC1518Y4VP
Top Assembly Part Number : 800-26851-03
Top Assembly Revision Number : C0
Version ID : V05
CLEI Code Number : COMB200BRA
Hardware Board Revision Number : 0x09
Switch Ports Model SW Version SW
Image
------ ----- ----- ----------
----------
* 1 28 WS-C3560G-24TS 15.0(1)SE
C3560-IPSERVICESK9-M
Configuration register is 0xF
!
3560Switch#sr int g0/22
Building configuration...
Current configuration : 176 bytes
!
interface GigabitEthernet0/22
no switchport
ip address 192.168.1.2 255.255.255.252
ip ospf network point-to-point
ip ospf hello-interval 2
ip ospf dead-interval 20
!
3560Switch#sh int g0/22
GigabitEthernet0/22 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is e8ba.70eb.a6d1 (bia
e8ba.70eb.a6d1)
Internet address is 192.168.1.2/30
MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 9/255, rxload 8/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 1000Mb/s, media type is 10/100/1000BaseTX
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 434
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 31592000 bits/sec, 7630 packets/sec
5 minute output rate 37916000 bits/sec, 43189 packets/sec
9857764843 packets input, 5428762085664 bytes, 0 no buffer
Received 623660 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 622706 multicast, 0 pause input
0 input packets with dribble condition detected
10000621950 packets output, 3259212102360 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
!
3560Switch#ping 192.168.1.1 rep 100000000 tim 1
!!!!!.!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Omitted about 5000
pings
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!.!!!!!!!!!!!!!!..!!!!!!!.!!!!!!!!!.!!.!!!!!.....!!!..!
......!!!!!!!!!!!!!!!!!!!!!!!..!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
This ping output is exactly the same when I try to ping 192.168.1.2 from
7609
At the moment of problem, I try to ping both devices using the Mikrotik
device which is in between, and at that time ping time increases including
some request time-out.
Thanks a lot and so sorry for such a long question.
_______________________________________________
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com
Are you a CCNP or CCIE and looking for a job? Check out
www.PlatinumPlacement.com
To Unsubscribe from this list please visit the following link and follow the
directions to unsubscribe. http://onlinestudylist.com/mailman/listinfo/ccie_rs
