Is it possible your bandwidth shaper device is kicking in and dropping pings?
It's one of two things as I would see it: 1) The Mikrotik device has a problem 2) The Mikrotik device is working as configured, and bandwidth shaping/QOS are dropping some of your test data. On Mon, Nov 21, 2011 at 11:39 AM, Mohammad Moghaddas <[email protected] > wrote: > Hi. > I'm currently experiencing a connectivity problem between a 7609 and a > 3560, which so matters for my current job position. > There is Mikrotik rb1200 RouterBoard between these to which two of its > ports are connected to the Router and Switch and I've made them bridge. I > use this Mikrotik Device as a Bandwidth Shaper. > When the 7609 and the 3560 are DIRECTLY connected, 7609 G5/2 <-> 3560 > G0/22, there is no problem! > But when the Mikrotik is inserted between, for a while everything is OK, > but accidentals the connectivity is lost, but after a while again it > changes to OK. > > Mikrotik ETH1 is connected to the 7609 G5/2 and is 1Gb and full-duplex as > ETH2 which is connected to the 3560 G5/22, and both are mapped to bridge1. > > 7609Router# sh ver > c7600rsp72043_rp Software (c7600rsp72043_rp-ADVENTERPRISEK9-M), Version > 15.1(3)S, RELEASE SOFTWARE (fc1) > Cisco CISCO7609-S (M8500) processor (revision 1.0) with 917504K/65536K > bytes of memory. > Processor board ID FOX1442H66G > BASEBOARD: RSP720 > CPU: MPC8548_E, Version: 2.0, (0x80390020) > CORE: E500, Version: 2.0, (0x80210020) > CPU:1200MHz, CCB:400MHz, DDR:200MHz, > L1: D-cache 32 kB enabled > I-cache 32 kB enabled > > Last reset from power-on > 1 SIP-400 controller (5 GigabitEthernet)(4 POS). > 1 Virtual Ethernet interface > 7 Gigabit Ethernet interfaces > 4 Packet over SONET interfaces > 3964K bytes of non-volatile configuration memory. > > 507024K bytes of Internal ATA PCMCIA card (Sector size 512 bytes). > Configuration register is 0x2102 > ! > 7609Router#sr int g5/2 > Building configuration... > > Current configuration : 241 bytes > ! > interface GigabitEthernet5/2 > description Connected to Core Switch > ip address 192.168.1.1 255.255.255.252 > ip ospf network point-to-point > ip ospf dead-interval 20 > ip ospf hello-interval 2 > no mdix auto > service-policy output SHAPE > ! > 7609Router#sh inter g5/2 > GigabitEthernet5/2 is up, line protocol is up (connected) > Hardware is C7600 1Gb 802.3, address is 588d.0912.6d80 (bia > 588d.0912.6d80) > Description: Connected to Core Switch > Internet address is 192.168.1.1/30 > MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec, > reliability 255/255, txload 6/255, rxload 8/255 > Encapsulation ARPA, loopback not set > Keepalive set (10 sec) > Full-duplex, 1000Mb/s, media type is T > Media-type configured as SFP connector > input flow-control is off, output flow-control is off > Clock mode is auto > ARP type: ARPA, ARP Timeout 04:00:00 > Last input 00:00:00, output 00:00:00, output hang never > Last clearing of "show interface" counters never > Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 > Queueing strategy: fifo > Output queue: 0/40 (size/max) > 5 minute input rate 31810000 bits/sec, 30156 packets/sec > 5 minute output rate 27354000 bits/sec, 6659 packets/sec > L2 Switched: ucast: 11490123 pkt, 1089129555 bytes - mcast: 601337 pkt, > 64168604 bytes > L3 in Switched: ucast: 9808379794 pkt, 3373019223246 bytes - mcast: 0 > pkt, 0 bytes mcast > L3 out Switched: ucast: 9861630782 pkt, 5796605234022 bytes mcast: 0 pkt, > 0 bytes > 9841352782 packets input, 3375755871116 bytes, 0 no buffer > Received 662805 broadcasts (0 IP multicasts) > 0 runts, 0 giants, 0 throttles > 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored > 0 watchdog, 0 multicast, 0 pause input > 0 input packets with dribble condition detected > 9879380703 packets output, 5812334751940 bytes, 0 underruns > 0 output errors, 0 collisions, 5 interface resets > 0 unknown protocol drops > 0 babbles, 0 late collision, 0 deferred > 0 lost carrier, 0 no carrier, 0 pause output > 0 output buffer failures, 0 output buffers swapped out > ! > 7609Router#sh mod all > Mod Ports Card Type Model Serial > No. > --- ----- -------------------------------------- ------------------ > ----------- > 5 2 Route Switch Processor 720 (Active) RSP720-3C-GE > JAE1224LBQV > 8 0 4-subslot SPA Interface Processor-400 7600-SIP-400 > JAE1125MAUY > > Mod MAC addresses Hw Fw Sw > Status > --- ---------------------------------- ----- ------------- ------------ > ------- > 5 001d.4558.fb9c to 001d.4558.fb9f 5.2 12.2(33r)SRD 15.1(3) Ok > 8 001b.53cc.d040 to 001b.53cc.d0bf 2.4 15.1(3)S 15.1(3)S Ok > > Mod Sub-Module Model Serial Hw > Status > ---- --------------------------- ------------------ ----------- ------- > ------- > 5 Policy Feature Card 3 7600-PFC3C JAE1224LAJO 1.1 Ok > 5 C7600 MSFC4 Daughterboard 7600-MSFC4 JAE1224L2FO 1.1 Ok > 8/0 5xGE SPA SPA-5X1GE-V2 JAE141003QJ 1.2 Ok > 8/1 4xOC3 POS SPA SPA-4XOC3-POS JAE12046H75 1.0 Ok > > Mod Online Diag Status > ---- ------------------- > 5 Pass > 8 Pass > 8/0 Pass > 8/1 Pass > ! > 7609Router#sh diagbus > Slot 8: Logical_index 16 > 4-subslot SPA Interface Processor-400 controller > Board is analyzed ipc ready > HW rev 2.4, board revision C0 > Serial Number: JAE1125MAUY Part number: 73-8404-14 > > Slot database information: > Flags: 0x2004 Insertion time: 0x1C81C (1w6d ago) > > Controller Memory Size: > 992 MBytes CPU Memory > 31 MBytes Packet Memory > 1023 MBytes Total on Board SDRAM > Cisco IOS Software, cwlc Software (sip2-DW-M), Version 15.1(3)S, > RELEASE SOFTWARE (fc1) > > SPA Information: > subslot 8/0: SPA-5X1GE-V2 (0x50A), status: ok > subslot 8/1: SPA-4XOC3-POS (0x440), status: ok > ! > 7609Router# sh diagnostic result all detail > > Current bootup diagnostic level: minimal > > Module 5: Route Switch Processor 720 (Active) SerialNo : JAE1224LBQV > > Overall Diagnostic Result for Module 5 : PASS > Diagnostic level at card bootup: minimal > > Test results: (. = Pass, F = Fail, U = Untested) > > > ___________________________________________________________________________ > > 1) TestScratchRegister -------------> . > > Error code ------------------> 0 (DIAG_SUCCESS) > Total run count -------------> 34753 > Last test testing type ------> Health Monitoring > Last test execution time ----> Nov 21 2011 20:04:02 > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> Nov 21 2011 20:04:02 > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________________ > > 2) TestSPRPInbandPing --------------> . > > Error code ------------------> 0 (DIAG_SUCCESS) > Total run count -------------> 69506 > Last test testing type ------> Health Monitoring > Last test execution time ----> Nov 21 2011 20:04:05 > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> Nov 21 2011 20:04:05 > Total failure count ---------> 0 > Consecutive failure count ---> 0 > CPU util(5sec) SP -----------> 9% > CPU util(5sec) RP -----------> 2% > Traffic ---------------------> 0% > netint_thr_active -----------> 0 > Inband Tx_Rate --------------> 1266 > Inband Rx_Rate --------------> 26 > Per-device Failure Count ----> n/a > > ___________________________________________________________________________ > > 3) TestTransceiverIntegrity: > > Port 1 2 > ---------- > . . > > > Error code ------------------> 0 (DIAG_SUCCESS) > Total run count -------------> 23 > Last test testing type ------> OnDemand > Last test execution time ----> Nov 09 2011 15:24:50 > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> Nov 09 2011 15:24:50 > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________________ > > 4) TestActiveToStandbyLoopback: > > Port 1 2 > ---------- > U U > > > Error code ------------------> 3 (DIAG_SKIPPED) > Total run count -------------> 0 > Last test testing type ------> n/a > Last test execution time ----> n/a > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> n/a > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________________ > > 5) TestLoopback: > > Port 1 2 > ---------- > . . > > > Error code ------------------> 0 (DIAG_SUCCESS) > Total run count -------------> 1 > Last test testing type ------> Bootup > Last test execution time ----> Nov 08 2011 18:14:21 > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> Nov 08 2011 18:14:21 > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________________ > > 6) TestNewIndexLearn ---------------> . > > Error code ------------------> 0 (DIAG_SUCCESS) > Total run count -------------> 1 > Last test testing type ------> Bootup > Last test execution time ----> Nov 08 2011 18:14:22 > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> Nov 08 2011 18:14:22 > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________________ > > 7) TestDontConditionalLearn --------> . > > Error code ------------------> 0 (DIAG_SUCCESS) > Total run count -------------> 1 > Last test testing type ------> Bootup > Last test execution time ----> Nov 08 2011 18:14:22 > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> Nov 08 2011 18:14:22 > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________________ > > 8) TestBadBpduTrap -----------------> . > > Error code ------------------> 0 (DIAG_SUCCESS) > Total run count -------------> 1 > Last test testing type ------> Bootup > Last test execution time ----> Nov 08 2011 18:14:22 > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> Nov 08 2011 18:14:22 > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________________ > > 9) TestMatchCapture ----------------> . > > Error code ------------------> 0 (DIAG_SUCCESS) > Total run count -------------> 1 > Last test testing type ------> Bootup > Last test execution time ----> Nov 08 2011 18:14:23 > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> Nov 08 2011 18:14:23 > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________________ > > 10) TestProtocolMatchChannel --------> . > > Error code ------------------> 0 (DIAG_SUCCESS) > Total run count -------------> 1 > Last test testing type ------> Bootup > Last test execution time ----> Nov 08 2011 18:14:24 > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> Nov 08 2011 18:14:24 > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________________ > > 11) TestFibDevices ------------------> . > > Error code ------------------> 0 (DIAG_SUCCESS) > Total run count -------------> 1 > Last test testing type ------> Bootup > Last test execution time ----> Nov 08 2011 18:14:25 > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> Nov 08 2011 18:14:25 > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________________ > > 12) TestIPv4FibShortcut -------------> . > > Error code ------------------> 0 (DIAG_SUCCESS) > Total run count -------------> 1 > Last test testing type ------> Bootup > Last test execution time ----> Nov 08 2011 18:14:25 > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> Nov 08 2011 18:14:25 > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________________ > > 13) TestL3Capture2 ------------------> . > > Error code ------------------> 0 (DIAG_SUCCESS) > Total run count -------------> 1 > Last test testing type ------> Bootup > Last test execution time ----> Nov 08 2011 18:14:25 > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> Nov 08 2011 18:14:25 > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________________ > > 14) TestIPv6FibShortcut -------------> . > > Error code ------------------> 0 (DIAG_SUCCESS) > Total run count -------------> 1 > Last test testing type ------> Bootup > Last test execution time ----> Nov 08 2011 18:14:26 > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> Nov 08 2011 18:14:26 > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________________ > > 15) TestMPLSFibShortcut -------------> . > > Error code ------------------> 0 (DIAG_SUCCESS) > Total run count -------------> 1 > Last test testing type ------> Bootup > Last test execution time ----> Nov 08 2011 18:14:26 > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> Nov 08 2011 18:14:26 > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________________ > > 16) TestNATFibShortcut --------------> . > > Error code ------------------> 0 (DIAG_SUCCESS) > Total run count -------------> 1 > Last test testing type ------> Bootup > Last test execution time ----> Nov 08 2011 18:14:26 > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> Nov 08 2011 18:14:26 > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________________ > > 17) TestAclPermit -------------------> . > > Error code ------------------> 0 (DIAG_SUCCESS) > Total run count -------------> 1 > Last test testing type ------> Bootup > Last test execution time ----> Nov 08 2011 18:14:26 > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> Nov 08 2011 18:14:26 > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________________ > > 18) TestQoSTcam ---------------------> . > > Error code ------------------> 0 (DIAG_SUCCESS) > Total run count -------------> 1 > Last test testing type ------> Bootup > Last test execution time ----> Nov 08 2011 18:14:27 > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> Nov 08 2011 18:14:27 > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________________ > > 19) TestL3VlanMet -------------------> . > > Error code ------------------> 0 (DIAG_SUCCESS) > Total run count -------------> 1 > Last test testing type ------> Bootup > Last test execution time ----> Nov 08 2011 18:14:27 > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> Nov 08 2011 18:14:27 > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________________ > > 20) TestIngressSpan -----------------> . > > Error code ------------------> 0 (DIAG_SUCCESS) > Total run count -------------> 1 > Last test testing type ------> Bootup > Last test execution time ----> Nov 08 2011 18:14:27 > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> Nov 08 2011 18:14:27 > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________________ > > 21) TestEgressSpan ------------------> . > > Error code ------------------> 0 (DIAG_SUCCESS) > Total run count -------------> 1 > Last test testing type ------> Bootup > Last test execution time ----> Nov 08 2011 18:14:27 > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> Nov 08 2011 18:14:27 > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________________ > > 22) TestNetflowInlineRewrite: > > Port 1 2 > ---------- > U U > > > Error code ------------------> 3 (DIAG_SKIPPED) > Total run count -------------> 0 > Last test testing type ------> n/a > Last test execution time ----> n/a > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> n/a > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________________ > > 23) TestFabricSnakeForward ----------> . > > Error code ------------------> 0 (DIAG_SUCCESS) > Total run count -------------> 1 > Last test testing type ------> Bootup > Last test execution time ----> Nov 08 2011 18:14:27 > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> Nov 08 2011 18:14:27 > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________________ > > 24) TestFabricSnakeBackward ---------> . > > Error code ------------------> 0 (DIAG_SUCCESS) > Total run count -------------> 1 > Last test testing type ------> Bootup > Last test execution time ----> Nov 08 2011 18:14:27 > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> Nov 08 2011 18:14:27 > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________________ > > 25) TestTrafficStress ---------------> U > > Error code ------------------> 3 (DIAG_SKIPPED) > Total run count -------------> 0 > Last test testing type ------> n/a > Last test execution time ----> n/a > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> n/a > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________________ > > 26) TestFibTcamSSRAM ----------------> U > > Error code ------------------> 3 (DIAG_SKIPPED) > Total run count -------------> 0 > Last test testing type ------> n/a > Last test execution time ----> n/a > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> n/a > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________________ > > 27) TestAsicMemory ------------------> U > > Error code ------------------> 3 (DIAG_SKIPPED) > Total run count -------------> 0 > Last test testing type ------> n/a > Last test execution time ----> n/a > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> n/a > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________________ > > 28) TestAclQosTcam ------------------> U > > Error code ------------------> 3 (DIAG_SKIPPED) > Total run count -------------> 0 > Last test testing type ------> n/a > Last test execution time ----> n/a > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> n/a > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________________ > > 29) TestNetflowTcam -----------------> U > > Error code ------------------> 3 (DIAG_SKIPPED) > Total run count -------------> 0 > Last test testing type ------> n/a > Last test execution time ----> n/a > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> n/a > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________________ > > 30) ScheduleSwitchover --------------> U > > Error code ------------------> 3 (DIAG_SKIPPED) > Total run count -------------> 0 > Last test testing type ------> n/a > Last test execution time ----> n/a > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> n/a > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________________ > > 31) FirmwareDiagStatus --------------> . > > Error code ------------------> 0 (DIAG_SUCCESS) > Total run count -------------> 1 > Last test testing type ------> Bootup > Last test execution time ----> Nov 08 2011 18:14:28 > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> Nov 08 2011 18:14:28 > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________________ > > 32) TestFabricFlowControlStatus -----> U > > Error code ------------------> 3 (DIAG_SKIPPED) > Total run count -------------> 0 > Last test testing type ------> n/a > Last test execution time ----> n/a > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> n/a > Total failure count ---------> 0 > Consecutive failure count ---> 0 > Current run count -------------------------->: 0 > First test execution time ------------------>: > Last test execution time ------------------->: > Total FPOE Rate0 Count --------------------->: 0 > Total FPOE Reduced Rate Count -------------->: 0 > > ___________________________________________________________________________ > > 33) TestErrorCounterMonitor ---------> . > > Error code ------------------> 0 (DIAG_SUCCESS) > Total run count -------------> 34753 > Last test testing type ------> Health Monitoring > Last test execution time ----> Nov 21 2011 20:04:05 > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> Nov 21 2011 20:04:05 > Total failure count ---------> 0 > Consecutive failure count ---> 0 > Error Records ---------------> n/a > > ___________________________________________________________________________ > > > Module 8: 4-subslot SPA Interface Processor-400 SerialNo : JAE1125MAUY > > Overall Diagnostic Result for Module 8 : PASS > Diagnostic level at card bootup: minimal > > Test results: (. = Pass, F = Fail, U = Untested) > > > ___________________________________________________________________________ > > 1) BusConnectivityTest -------------> . > > Error code ------------------> 0 (DIAG_SUCCESS) > Total run count -------------> 486479 > Last test testing type ------> Health Monitoring > Last test execution time ----> Nov 21 2011 20:04:16 > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> Nov 21 2011 20:04:16 > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________________ > > 2) TestEobcStressPing --------------> U > > Error code ------------------> 3 (DIAG_SKIPPED) > Total run count -------------> 0 > Last test testing type ------> n/a > Last test execution time ----> n/a > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> n/a > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________________ > > 3) TestFirmwareDiagStatus ----------> . > > Error code ------------------> 0 (DIAG_SUCCESS) > Total run count -------------> 1 > Last test testing type ------> Bootup > Last test execution time ----> Nov 08 2011 18:15:24 > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> Nov 08 2011 18:15:24 > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________________ > > > Module 8/0: 5xGE SPA SerialNo : JAE141003QJ SerialNo : > JAE1125MAUY > > Overall Diagnostic Result for Module 8/0 : PASS > Diagnostic level at card bootup: minimal > > Test results: (. = Pass, F = Fail, U = Untested) > > > ___________________________________________________________________ > > 1) TestSpaScratchRegister ----------> . > > Error code ------------------> 0 (DIAG_SUCCESS) > Total run count -------------> 1 > Last test testing type ------> Bootup > Last test execution time ----> Nov 08 2011 18:15:29 > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> Nov 08 2011 18:15:29 > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________ > > 2) PortLoopbackTest: > > Port 1 2 3 4 5 > ------------------- > U U U U U > > > Error code ------------------> 3 (DIAG_SKIPPED) > Total run count -------------> 0 > Last test testing type ------> n/a > Last test execution time ----> n/a > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> n/a > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________ > > > Module 8/1: 4xOC3 POS SPA SerialNo : JAE12046H75 SerialNo : > JAE1125MAUY > > Overall Diagnostic Result for Module 8/1 : PASS > Diagnostic level at card bootup: minimal > > Test results: (. = Pass, F = Fail, U = Untested) > > > ___________________________________________________________________ > > 1) TestSpaScratchRegister ----------> . > > Error code ------------------> 0 (DIAG_SUCCESS) > Total run count -------------> 1 > Last test testing type ------> Bootup > Last test execution time ----> Nov 08 2011 18:15:30 > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> Nov 08 2011 18:15:30 > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________ > > 2) PortLoopbackTest: > > Port 1 2 3 4 > ---------------- > U U U U > > > Error code ------------------> 3 (DIAG_SKIPPED) > Total run count -------------> 0 > Last test testing type ------> n/a > Last test execution time ----> n/a > First test failure time -----> n/a > Last test failure time ------> n/a > Last test pass time ---------> n/a > Total failure count ---------> 0 > Consecutive failure count ---> 0 > > ___________________________________________________________________ > ! > ====================================== > 3560Switch#sh ver > C3560 Software (C3560-IPSERVICESK9-M), Version 15.0(1)SE, RELEASE SOFTWARE > (fc1) > cisco WS-C3560G-24TS (PowerPC405) processor (revision F0) with 131072K > bytes of memory. > Processor board ID FOC1518Y4VP > Last reset from power-on > 3 Virtual Ethernet interfaces > 28 Gigabit Ethernet interfaces > The password-recovery mechanism is enabled. > > 512K bytes of flash-simulated non-volatile configuration memory. > Base ethernet MAC Address : E8:BA:70:EB:A6:80 > Motherboard assembly number : 73-10215-06 > Power supply part number : 341-0098-02 > Motherboard serial number : FOC151805NM > Power supply serial number : AZS15180166 > Model revision number : F0 > Motherboard revision number : A0 > Model number : WS-C3560G-24TS-S > System serial number : FOC1518Y4VP > Top Assembly Part Number : 800-26851-03 > Top Assembly Revision Number : C0 > Version ID : V05 > CLEI Code Number : COMB200BRA > Hardware Board Revision Number : 0x09 > > > Switch Ports Model SW Version SW > Image > ------ ----- ----- ---------- > ---------- > * 1 28 WS-C3560G-24TS 15.0(1)SE > C3560-IPSERVICESK9-M > > > Configuration register is 0xF > ! > 3560Switch#sr int g0/22 > Building configuration... > > Current configuration : 176 bytes > ! > interface GigabitEthernet0/22 > no switchport > ip address 192.168.1.2 255.255.255.252 > ip ospf network point-to-point > ip ospf hello-interval 2 > ip ospf dead-interval 20 > ! > 3560Switch#sh int g0/22 > GigabitEthernet0/22 is up, line protocol is up (connected) > Hardware is Gigabit Ethernet, address is e8ba.70eb.a6d1 (bia > e8ba.70eb.a6d1) > Internet address is 192.168.1.2/30 > MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec, > reliability 255/255, txload 9/255, rxload 8/255 > Encapsulation ARPA, loopback not set > Keepalive set (10 sec) > Full-duplex, 1000Mb/s, media type is 10/100/1000BaseTX > input flow-control is off, output flow-control is unsupported > ARP type: ARPA, ARP Timeout 04:00:00 > Last input 00:00:00, output 00:00:00, output hang never > Last clearing of "show interface" counters never > Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 434 > Queueing strategy: fifo > Output queue: 0/40 (size/max) > 5 minute input rate 31592000 bits/sec, 7630 packets/sec > 5 minute output rate 37916000 bits/sec, 43189 packets/sec > 9857764843 packets input, 5428762085664 bytes, 0 no buffer > Received 623660 broadcasts (0 IP multicasts) > 0 runts, 0 giants, 0 throttles > 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored > 0 watchdog, 622706 multicast, 0 pause input > 0 input packets with dribble condition detected > 10000621950 packets output, 3259212102360 bytes, 0 underruns > 0 output errors, 0 collisions, 1 interface resets > 0 unknown protocol drops > 0 babbles, 0 late collision, 0 deferred > 0 lost carrier, 0 no carrier, 0 pause output > 0 output buffer failures, 0 output buffers swapped out > ! > 3560Switch#ping 192.168.1.1 rep 100000000 tim 1 > !!!!!.!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! > !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! > !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! > !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! > !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! > !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! > !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! > !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! > !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! > !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! > !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! > !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! > !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! > !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Omitted about 5000 > pings > !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! > !!!!!!!!!!!!!!!!.!!!!!!!!!!!!!!..!!!!!!!.!!!!!!!!!.!!.!!!!!.....!!!..! > ......!!!!!!!!!!!!!!!!!!!!!!!..!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! > !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! > !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! > !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! > !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! > !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! > !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! > !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! > !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! > > This ping output is exactly the same when I try to ping 192.168.1.2 from > 7609 > At the moment of problem, I try to ping both devices using the Mikrotik > device which is in between, and at that time ping time increases including > some request time-out. > Thanks a lot and so sorry for such a long question. > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > Are you a CCNP or CCIE and looking for a job? Check out > www.PlatinumPlacement.com > > To Unsubscribe from this list please visit the following link and follow > the directions to unsubscribe. > http://onlinestudylist.com/mailman/listinfo/ccie_rs > _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com To Unsubscribe from this list please visit the following link and follow the directions to unsubscribe. http://onlinestudylist.com/mailman/listinfo/ccie_rs
