Hi guys, many thanks for all the feedback - I wasn't even thinking about VM integration anymore, so thanks for the really helpful tip Ovias - I'm going to try it out for sure. But to come back on my first Q: has anyone experienced the same thing regarding the ''Dialed Number'' information in Unity's call viewer (ie. it doesn't reflect the originator, but the redirecting number)? I both set the Redirecting Number IE Delivery on inbound and outbound, but that didn't help, and you can only set the ''Calling party selection'' to ''originator'' on the outbound GW - but that's the MGCP PRI that falls back to H323. Regards, Juan
________________________________ From: jason sung [mailto:[EMAIL PROTECTED] Sent: Monday, February 18, 2008 3:53 PM To: [EMAIL PROTECTED] Cc: Matthew Saskin; ccie_voice@onlinestudylist.com; Juan Lopez Hernandez -X (jlopezhe - IBM - INS at Cisco) Subject: Re: [OSL | CCIE_Voice] called number in Unity's Call Viewer mimicsForwardingnumber I see... I will go with VM-Integration for the lab and if I have time I might even give RDNIS a shot. (Time: who am I kidding)... Thanks Ovais, Matt. On Feb 18, 2008 8:51 AM, Ovais Iqbal <[EMAIL PROTECTED]> wrote: Hey Jason, U really need vm-integration configuration for your real lab, its fine if you want to test both options in your home lab. Ovais Iqbal 416-294-7869 Sent from my BlackBerry device -----Original Message----- From: Matthew Saskin <[EMAIL PROTECTED]> Date: Mon, 18 Feb 2008 09:49:23 To:jason sung <[EMAIL PROTECTED]> Cc:[EMAIL PROTECTED], ccie_voice@onlinestudylist.com, "Juan Lopez Hernandez -X (jlopezhe - IBM - INS at Cisco)" <[EMAIL PROTECTED]> Subject: Re: [OSL | CCIE_Voice] called number in Unity's Call Viewer mimicsForwarding number There's no guarantee that RDNIS will actually work however - I've come across plenty of telco's where RDNIS just gets lost in the network... -matt jason sung wrote: > Juan, > > You are correct about VM-Integration needed only for analog or CAS > circuits, because in this case DTMF tones are used to route call to > the appropriate mailbox. For PRIs all you have do is configure > complete 10 digit number as voicemail under fallback and check "RDNIS > outgoing" on central site PRI. > > Mark or Vik: Can you please confirm this step? > > Neverthless Ovais, thanks for the attahed configuration note. > Appreciate it. > > Thanks > > On Feb 17, 2008 8:56 AM, Ovais Iqbal <[EMAIL PROTECTED] > <mailto:[EMAIL PROTECTED]>> wrote: > > Vm-integration also works for PRI ports but u need to configure it > properly. I am not infront of my computer right now, I can send > you a config later if u want. > > > Ovais Iqbal > 416-294-7869 > Sent from my BlackBerry device > > -----Original Message----- > From: "Juan Lopez Hernandez -X (jlopezhe - IBM - INS at Cisco)" > <[EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]>> > > Date: Sun, 17 Feb 2008 10:59:25 > To:"ovais Iqbal" <[EMAIL PROTECTED] > <mailto:[EMAIL PROTECTED]>>, "jason sung" <[EMAIL PROTECTED] > <mailto:[EMAIL PROTECTED]>> > Cc:<ccie_voice@onlinestudylist.com > <mailto:ccie_voice@onlinestudylist.com>> > Subject: RE: [OSL | CCIE_Voice] called number in Unity's Call > Viewer mimicsForwarding number > > > Hi Ovais and Jason, > > thanks for the reply on this. On CCM I already checked > the'"Redirecting Number IE Delivery - Inbound'' checkbox on the > (incoming) HQ gateway. You can also see the Called Party Number > and the RedirectingNumber that comes into CCM from the trace below > - but Unity's Call Viewer doesn't show the correct ''dialed > number'' though... > > Ovais, the VM-Integration, is that supported for PRI calls? I > thought it only worked for analog - or T1 CAS/E1 r2 - line's - but > I can be wrong of course? > > Kind regards, > Juan > > > ---------------- > From: [EMAIL PROTECTED] > <mailto:[EMAIL PROTECTED]> > [mailto:[EMAIL PROTECTED] > <mailto:[EMAIL PROTECTED]>] On Behalf Of > ovais Iqbal > Sent: Saturday, February 16, 2008 4:47 AM > To: jason sung > Cc: ccie_voice@onlinestudylist.com > <mailto:ccie_voice@onlinestudylist.com>; Juan Lopez Hernandez -X > (jlopezhe - IBM - INS at Cisco) > Subject: Re: [OSL | CCIE_Voice] called number in Unity's Call > Viewer mimicsForwarding number > > > by the way my understanding is that in the real LAB the RDNIS does > not work today - you would need VM-Integration option to be > configured to get it work properly in your real lab. I know at > home I made it to work with redirected number option. > > > On 2/15/08, jason sung <[EMAIL PROTECTED] > <mailto:[EMAIL PROTECTED]> <mailto:[EMAIL PROTECTED] > <mailto:[EMAIL PROTECTED]>> > wrote: > Juan, > > You may have already done this, Is the RDNIS box checked on the HQ > PRI? > > > > On Feb 15, 2008 2:28 PM, Juan Lopez Hernandez -X (jlopezhe - IBM - > INS at Cisco) <[EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]> > <mailto:[EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]>> > wrote: > > > Hello, > > I need some help as I can't figure out the following: I try to > test Unity with BR1 in SRST. All is going fine, the call to unity > is set up over PSTN, redirecting number works fine. From the CCM > trace files I see the call coming in as: > > SETUP pd = 8 callref = 0x00AB > Bearer Capability i = 0x8090A3 > Channel ID i = 0xA98381 > Calling Party Number i = '!', 0x80, '6175252001' > Called Party Number i = 0x80, '2122251600' <------- 4 last > digits are the Unity pilot number - this incoming number gets > stripped to ''1600'' > Redirecting Number i = 0x000082, '6175252002' > > When looking into Unity's Call Viewer, I notice that the ''dialed > number'' always follows the ''forwarding number''. So instead of > seeing the number 1600 as dialed number in the Call Viewer , I see > whatever is the forwarding number. Is there a setting that can be > changed so you see the correct ''dialed number''? > > Kind regards, > Juan > > > > > > > > > -- > Ovais Iqbal > 416-294-7869 > >
