Hey Vik, High Five for your detailed kind responce on this. Appreciate it.
Regards, Anil --- On Tue, 12/16/08, Vik Malhi <vma...@ipexpert.com> wrote: > From: Vik Malhi <vma...@ipexpert.com> > Subject: Re: [OSL | CCIE_Voice] Alias command not working in SRST > To: "James Key" <j...@jackhenry.com>, anil...@yahoo.com, "Ryan Trauernicht" > <ryanstudyvo...@gmail.com> > Cc: ccie_voice@onlinestudylist.com > Date: Tuesday, December 16, 2008, 12:18 AM > The Alias command just creates another dial-peer. You can > see the effect of > the alias command by "show call-manager-fallback > dial-peer" > > Take a look at this example: > > Call-manager-fallback > max-dn 4 preference 2 > alias 1 2000 to 2002 > > In this example extension 2000 is not being used and is > forwarded to 2002. > Simple enough. If you did use dialplan pattern then this > would be used: > > Call-manager-fallback > max-dn 4 preference 2 > alias 1 6175212000 to 2002 > > > Now- lets just say that all phones should be fwded to > voicemail ("1600") > except 2002 which should be forward to a cell phone > ("911"- yes I know!). > > Call-manager-fallback > max-dn 4 preference 2 > call-forward busy 1600 > call-forward noan 1600 timeout 12 > alias 1 2002 to 2002 preference 1 cfw 911 timeout 12 > > Now- the two "call-forward" statements are to be > used globally for all > phones in SRST mode. For extn "2002" you will see > two dial-peers using the > "show call-manager-fallback dial-peer" command: > > Dial-peer voice 20002 pots > destination-pattern 2002 > port 50/0/2 > call-forward busy 1600 > call-forward noan 1600 timeout 12 > preference 2 ! From preference after "max-dn" > > ... > > > The dial-peer above is created when the phone registers and > cannot be > removed (unless extn 2002 is not registered to srst). The > dial-peer is NOT > going to be used since the dial-peer created by the alias > command is a lower > preference... > > This is the dial-peer from the alias command: > > Dial-peer voice 200XX pots > destination-pattern 2002 > port 50/0/2 > call-forward busy 911 ! From CFW after alias > call-forward noan 911 timeout 12 ! From CFW after alias > preference 1 ! From preference after "alias" > ... > > So you see that "preference" after max-dn enables > the alias to be active. > > Think of the alias command as being > "destination-pattern" to "port". > > If you wanted to forward an unegistered phone (extn > "2000") to a PSTN number > ("911") without ringing an internal phone then > the alias command will not > achieve that since you HAVE to point an alias to a > registered phone. The > answer to this question is simply add a dial-peer for the > unregistered > phone- > > Dial-peer voice 2000 pots > destination-pattern 2000 > port 0/0/0:23 > prefix 911 > > > Hopefully this clears up the alias command! > > > > > -- > Vik Malhi CCIE #13890, CCSI #31584 > Senior Technical Instructor - IPexpert, Inc. > > Telephone: +1.810.326.1444 > Fax: +1.810.454.0130 > Mailto: vma...@ipexpert.com > > > Join our free online support and peer group communities: > http://www.IPexpert.com/communities > IPexpert - The Global Leader in Self-Study, > Classroom-Based, Video-On-Demand > and Audio Certification Training Tools for the Cisco CCIE > R&S Lab, CCIE > Security Lab, CCIE Service Provider Lab , CCIE Voice Lab > and CCIE Storage > Lab Certifications. > > > > > > > > > From: James Key <j...@jackhenry.com> > > Date: Mon, 15 Dec 2008 07:57:46 -0600 > > To: <anil...@yahoo.com>, Ryan Trauernicht > <ryanstudyvo...@gmail.com> > > Cc: <ccie_voice@onlinestudylist.com> > > Subject: Re: [OSL | CCIE_Voice] Alias command not > working in SRST > > > > I don't believe Alias with work if you have > dialplan-pattern defined. > > > > James > > > > > > -----Original Message----- > > From: ccie_voice-boun...@onlinestudylist.com > > [mailto:ccie_voice-boun...@onlinestudylist.com] On > Behalf Of anil batra > > Sent: Monday, December 15, 2008 1:13 AM > > To: Ryan Trauernicht > > Cc: ccie_voice@onlinestudylist.com > > Subject: Re: [OSL | CCIE_Voice] Alias command not > working in SRST > > > > Hi Ryan, > > > > Sorry for my delayed repsponse as was out on a > project, Here is what I > > am trying to test and my configs please. > > > > May be if Vik or Mark can put more lights on this one > please...as I ma > > stuck here. > > > > > > Call a number say "2002" which is not > registerd in SRST mode , only > > "2001" is regosterd, Now I am trying ot use > the alias command tro > > forweard the calls coming to "2002" to HQ > number 212 223 1001 > > > > > > My doubt is "will it the Alias command work for > any un-registered phone > > or will I have to have the phone 2002 registred to > SRST first and then > > use alias command to forward it to some other number. > So I am lost in > > what case the alias commned will work please. > > > > here is my config for you reference..... > > > > call-manager-fallback > > max-conferences 2 gain -6 > > transfer-system full-consult > > ip source-address 10.2.201.1 port 2000 > > max-ephones 1 > > max-dn 2 preference 2 > > sdspfarm units 2 > > sdspfarm transcode sessions 3 > > dialplan-pattern 1 6175222... extension-length 4 > > transfer-pattern .T > > keepalive 10 > > voicemail 12122221600 > > alias 2 2002 to 2002 cfw 912122221001 timeout 10 > > call-forward pattern .T > > call-forward busy 12122221600 > > call-forward noan 12122221600 timeout 10 > > moh music-on-hold.au > > > > > > I have tried it without dialpattern command too abd > using transaltion > > profiles at voice-port but no luck.. > > > > Kinldy help... > > > > Thanks, > > Anil > > > > > > > > > > > > > > > > > > > > > > --- On Mon, 12/8/08, Ryan Trauernicht > <ryanstudyvo...@gmail.com> wrote: > > > >> From: Ryan Trauernicht > <ryanstudyvo...@gmail.com> > >> Subject: Re: [OSL | CCIE_Voice] Alias command not > working in SRST > >> To: anil...@yahoo.com > >> Cc: ccie_voice@onlinestudylist.com > >> Date: Monday, December 8, 2008, 7:10 AM > >> What are you trying to do here... ring 2002 then > call > >> forward noan to that > >> DID? I can't remember off the top of my head > the order > >> in which things are > >> matched against. If you have a DN on a phone that > is > >> registered in SRST as > >> 2002, it might match that and ring before it hits > your > >> alias commands and > >> that is why it is not working. I would double > check on > >> that. > >> > >> You can test by calling is 2003 (that isnt a DN on > a phone) > >> to alias that to > >> 2002 with cfw to the DID. > >> > >> See if that works. > >> > >> Thanks, > >> Ryan Trauernicht > >> > >> On Thu, Dec 4, 2008 at 9:55 PM, anil batra > >> <anil...@yahoo.com> wrote: > >> > >>> Hello Experts, > >>> > >>> I tried several times to use alias command in > SRST but > >> without any lcuk. > >>> > >>> Here is what I did - > >>> > >>> ON CCM - created two DP- one for srst and > non-srst and > >> applied to BR1 ph1 > >>> ad ph2 respectively. > >>> > >>> ON BR1 router- > >>> call-manager-fallback > >>> alias i 2002 to 2002 prefernce 1 cfw > 912122231001 > >>> > >>> > >>> I do have dial-peer for long distnce call to > HQ phone > >> 2122231001 > >>> > >>> I tired with dial-pattern command and without > but no > >> luck. > >>> > >>> Any help on this will be higly apreciated. > >>> > >>> Thanks, > >>> Anil > >>> > >>> > >>> > >>> > >>> > >>> > >>> > > > > > > > > NOTICE: This electronic mail message and any files > transmitted with it are > > intended > > exclusively for the individual or entity to which it > is addressed. The > > message, > > together with any attachment, may contain confidential > and/or privileged > > information. > > Any unauthorized review, use, printing, saving, > copying, disclosure or > > distribution > > is strictly prohibited. If you have received this > message in error, please > > immediately advise the sender by reply email and > delete all copies. > >