Michael, I'm in a similar situation as if using their rack remotely.. We put our labs out in our data center for various reasons and I only have 4-5 cat5 runs to the cabinet, so I'm trying to come up with an easy solution by mirroring their design as if my rack was remote like theirs.
You're saying just use four phones? two off BR2, one of BR1, one off HQ ? i guess that's such a simple solution I didn't even consider it until just now. -jeff On Thu, Aug 6, 2009 at 12:54 AM, Michael Ciarfello <[email protected]>wrote: > The hardware shouldn't matter so much as long as it has the correct > capabilities. I would move the cards around every once in an while, use > different IP address scheme and dial-plan scheme. > > HWIC will work fine. Phones will need power bricks as you say. > > The internet cloud is for Ipexpert. Their equipment is at a data center > with a couple phones on auto answer. The phones in the cloud are the phones > you can touch. If you have all home lab gear, ignore the internet phones > and cloud. > > > > ------------------------------ > *From:* [email protected] [[email protected]] On Behalf Of Jeff Garvas [ > [email protected]] > *Sent:* Thursday, August 06, 2009 12:25 AM > *To:* Michael Ciarfello > *Cc:* Andrew; [email protected] > *Subject:* Re: [OSL | CCIE_Voice] Home lab - How to load initial server > configs ? > > Michael, > > Great points. I'm expecting to need to define my card types since some of > them are E1/T1 capable. I'm specifically re-configuring my hardware this > weekend to match the IPX hardware as much as possible, specifically with the > controller card slot assignments. Maybe Vik or Mark (or anyone else here) > could provide some input for me here. > > I bought a 3825 for BR2 but it seems IPX is using straight 2811's. Any > reason not to stick with my 3825? > I found an HWIC-4ESW today but its not POE. Can I just put this in BR2 and > use external power bricks for those two BR2 phones? > > For those of us labbing up at home/work how should we physically connect > the phones that are depicted in the drawing off the internet cloud? > > -Jeff > > > On Wed, Aug 5, 2009 at 11:46 PM, Michael Ciarfello <[email protected] > > wrote: > >> I'm not. But to do so I would guess just substitute your interfaces in >> place of their interfaces. >> There are probably a bunch of other commands that need replacing. Then >> paste it into your router. >> >> I have my own dial-plan, IP addresses and directory numbers. It's a >> little confusing when working through the workbooks, but a diagram seems to >> help. >> >> Looking through the HQ RTR for lab 5b initial >> You have to change at least the following commands: >> >> network-clock-select 1 T1 0/0/0 >> >> controller T1 0/0/0 (and other controllers depending on your config) >> >> interface Serial0/0/0:23 (which comes from the controller) >> >> interface Serial0/0/1:0 for the data. Sub-interfaces need to change also. >> >> >> >> all dial-peers that point to a physical inteface need to change (911, >> 91212, 7, 11) >> >> >> >> Think that's it. Wasn't as bad as I thought. You might have to do some >> troubleshooting to see why something isn't working, but should not be too >> much a problem. >> >> >> ------------------------------ >> *From:* [email protected] [ >> [email protected]] On Behalf Of Andrew [ >> [email protected]] >> *Sent:* Wednesday, August 05, 2009 8:04 PM >> *To:* [email protected] >> *Subject:* [OSL | CCIE_Voice] Home lab - How to load initial server >> configs ? >> >> Hi >> >> For a home lab set up, how are you guys installing the initial configs? >> For the routers / switch it is straight forward (copy / paste), but what >> about the servers? >> >> Andy >> >> _______________________________________________ >> For more information regarding industry leading CCIE Lab training, please >> visit www.ipexpert.com >> >> >
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
