I am calling from BR2 to the PSTN....
Jonathan On Thu, Aug 20, 2009 at 4:52 PM, Aamir Panjwani<[email protected]> wrote: > It appears that your are calling from HQ to PSTN right? Have you tried > running debug isdn q931 on the PSTN router to see if it is actually receiving > + sign. You may need to tweak some config on PSTN router to be able to > display +sign > > > > -----Original Message----- > From: [email protected] > [mailto:[email protected]] On Behalf Of Jonathan Charles > Sent: Friday, 21 August 2009 6:40 AM > To: [email protected] > Subject: Re: [OSL | CCIE_Voice] international escape character and h.323 > > Or, it is not supported... > > http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/admin/7_0_1/ccmfeat/fscallpn.pdf > > great. > > > J > > > On Thu, Aug 20, 2009 at 3:37 PM, Jonathan Charles<[email protected]> wrote: >> Also, there are H.323 translations on the gateway: >> >> >> ! >> voice translation-rule 1 >> rule 1 /3313214\(3...\)$/ /\1/ >> ! >> voice translation-rule 2 >> rule 1 /^\(3...\)$/ /+3313214\1/ >> ! >> ! >> voice translation-profile ANI >> translate calling 2 >> ! >> voice translation-profile DNIS >> translate called 1 >> ! >> voice-port 0/0/0:15 >> translation-profile incoming DNIS >> translation-profile outgoing ANI >> ! >> >> BR2#test voice translation-rule 2 3002 >> Matched with rule 1 >> Original number: 3002 Translated number: +33132143002 >> Original number type: none Translated number type: none >> Original number plan: none Translated number plan: none >> >> BR2# >> >> But when I call out: >> >> Aug 20 20:35:59.261: ISDN Se0/0/0:15 Q931: Applying typeplan for >> sw-type 0x12 is 0x0 0x0, Calling num 33132143002 >> Aug 20 20:35:59.261: ISDN Se0/0/0:15 Q931: Sending SETUP callref = >> 0x0083 callID = 0x8004 switch = primary-net5 interface = User >> Aug 20 20:35:59.261: ISDN Se0/0/0:15 Q931: TX -> SETUP pd = 8 callref = >> 0x0083 >> Bearer Capability i = 0x8090A3 >> Standard = CCITT >> Transfer Capability = Speech >> Transfer Mode = Circuit >> Transfer Rate = 64 kbit/s >> Channel ID i = 0xA98386 >> Exclusive, Channel 6 >> Calling Party Number i = 0x0081, '33132143002' >> Plan:Unknown, Type:Unknown >> Called Party Number i = 0x80, '999' >> Plan:Unknown, Type:Unknown >> BR2# >> Aug 20 20:35:59.293: ISDN Se0/0/0:15 Q931: RX <- CALL_PROC pd = 8 >> callref = 0x8083 >> Channel ID i = 0xA98386 >> Exclusive, Channel 6 >> Aug 20 20:35:59.305: ISDN Se0/0/0:15 Q931: RX <- ALERTING pd = 8 >> callref = 0x8083 >> Progress Ind i = 0x8188 - In-band info or appropriate now available >> BR2# >> Aug 20 20:36:02.897: ISDN Se0/0/0:15 Q931: TX -> DISCONNECT pd = 8 >> callref = 0x0083 >> Cause i = 0x8090 - Normal call clearing >> Aug 20 20:36:02.905: ISDN Se0/0/0:15 Q931: RX <- RELEASE pd = 8 >> callref = 0x8083 >> Aug 20 20:36:02.909: ISDN Se0/0/0:15 Q931: TX -> RELEASE_COMP pd = 8 >> callref = 0x0083 >> >> No plus sign... >> >> >> Why? >> >> On Thu, Aug 20, 2009 at 3:32 PM, Jonathan Charles<[email protected]> wrote: >>> OK, so I configured the + to be sent... and I see it on an H.323 gateway: >>> >>> >>> BR2# >>> BR2# >>> Aug 20 20:22:43.375: ISDN Se0/0/0:15 Q931: RX <- SETUP pd = 8 callref = >>> 0x009D >>> Bearer Capability i = 0x8090A3 >>> Standard = CCITT >>> Transfer Capability = Speech >>> Transfer Mode = Circuit >>> Transfer Rate = 64 kbit/s >>> Channel ID i = 0xA98381 >>> Exclusive, Channel 1 >>> Display i = 'HQ Ph1' >>> Calling Party Number i = 0x0081, '+12123945001' >>> Plan:Unknown, Type:Unknown >>> Called Party Number i = 0x91, '33132143002' >>> Plan:ISDN, Type:International >>> Aug 20 20:22:43.375: ISDN Se0/0/0:15 Q931: Received SETUP callref = >>> 0x809D callID = 0x000D switch = primary-net5 interface = User >>> BR2# >>> Aug 20 20:22:43.387: ISDN Se0/0/0:15 Q931: TX -> CALL_PROC pd = 8 >>> callref = 0x809D >>> Channel ID i = 0xA98381 >>> Exclusive, Channel 1 >>> Aug 20 20:22:43.507: ISDN Se0/0/0:15 Q931: TX -> ALERTING pd = 8 >>> callref = 0x809D >>> BR2# >>> Aug 20 20:22:48.003: ISDN Se0/0/0:15 Q931: RX <- DISCONNECT pd = 8 >>> callref = 0x009D >>> Cause i = 0x8290 - Normal call clearing >>> Aug 20 20:22:48.007: ISDN Se0/0/0:15 Q931: TX -> RELEASE pd = 8 >>> callref = 0x809D >>> Aug 20 20:22:48.015: ISDN Se0/0/0:15 Q931: RX <- RELEASE_COMP pd = 8 >>> callref = 0x009D >>> BR2# >>> BR2# >>> >>> But it is not showing up on the phone.... >>> >>> The Device Pool for that site has the + for International calls, but >>> they aren't showing up.... any ideas? >>> >>> >>> >>> Jonathan >>> >> > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > ______________________________________________________________________ > This email has been scanned by the MessageLabs Email Security System. > For more information please visit http://www.messagelabs.com/email > ______________________________________________________________________ > > ______________________________________________________________________ > This email has been scanned by the MessageLabs Email Security System. > For more information please visit http://www.messagelabs.com/email > ______________________________________________________________________ > _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com
