You said your using SLRG? You did assign a route group to each device-pool and reset, correct?
Chris On Tue, Nov 15, 2011 at 1:42 PM, Voiper <datapack...@gmail.com> wrote: > Unfortunately, I am still stuck. I took two days off from work (Mon, Tue) > to work on it and still no success [?] > Will keep trying. > > Thanks, > > Voiper > > > On Tue, Nov 15, 2011 at 2:35 PM, Rrcrumm <rrcr...@yahoo.com> wrote: > >> We're u able to resolve your issue? >> >> Sent from my iPhone >> >> On Nov 15, 2011, at 10:32 AM, Voiper <datapack...@gmail.com> wrote: >> >> Hi Friends: >> >> Thank you all for you quick and helpful suggestions. It show you are all >> very focused and have the determination to get the coveted number. I need >> to step up my efforts after seeing how you all quickly helped with >> feedback. >> >> All your help is truly appreciated. >> >> Voiper >> >> >> @RRCRUMM: >> Did you reset the h323 gw in cucm? Do you see an ip address towards the >> upper portion of the page above the name/ ip address field? >> -> The h323 gw is configured and I see the ip address >> outbound calls to pstn using h323 or mcgp gw directly is working >> >> @Ashwani ash_r...@hotmail.com >> Did you bind source interface on HQ router for H323? And same interface's >> IP assigned on CUCM? Also did you have incoming dial-peer from CUCM? Paste >> your HQ config here. >> -> interface FastEthernet0/0.20 >> description VOICE >> encapsulation dot1Q 20 >> ip address 10.10.200.3 255.255.255.0 >> ip helper-address 10.10.210.10 >> h323-gateway voip bind srcaddr 10.10.200.3 >> >> HQ router config is attached. >> >> @Ken Wyan kew...@gmail.com >> Pls check your route list rl-test config & digit manipulations etc.. in >> rg-test (under rl-test). >> If you have done any digit manipulations in rg-test (under rl-test) , >> your RP digit-manipulations will not work >> Add rg-test as Local Route Group for Device Pool >> In addition to debug isdn ---> debug ccapi inout , dialpeer may help to >> isolate issue >> -> No digit manipulations on any of the above. I tried to keep it as >> simple as possible >> ran above debug and nothing gets generated. >> >> @Pradeep Kumar Sharma sonu.netwo...@gmail.com >> Verify the registration status of your Route List. >> Try to reset it once. >> Run the debug voice ccapi inout on H323 Gw and see if the outbound calls >> really hitting to the gateway on not ? >> -> route list status unknown. Reset many times. What is your registration >> status? >> >> CCAPI: debug voip ccapi inout is ON (filter is OFF) >> CCH323 SPI: H225 State Machine tracing is enabled (filter is OFF) >> -> above debug show nothing happening. Call just not reaching the h323 gw >> >> >> @Mohd Baqari baqari.voic...@gmail.com >> On you gateway, do the following: >> 1. Debug cch323 h225 messages. Check if any h323 signaling is reaching >> the gateway. >> 2. If signaling is received successfully, run the command debug voice >> dialpeer. Check which dial peer is matched and whats the configuration of it >> 3. If no h323 signaling is received, post cucm traces after making a call >> -> above debug show nothing happening. Call just not reaching the h323 gw >> Do I need to run RTMT for trace? I installed it on my desktop and ran >> trace 'Collect Files' (attached). First time using, so I don't know if I >> got the right one? >> >> >> <ccm00000007.txt> >> >> <ccm00000007.txt> >> >> <SDL002_100_000010.txt> >> >> <HQ-RTR.txt> >> >> > > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > Are you a CCNP or CCIE and looking for a job? Check out > www.PlatinumPlacement.com >
<<33D.gif>>
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com