Bill what lab are you working on? On Sun, Nov 27, 2011 at 7:55 AM, Bill Lake <whl...@gmail.com> wrote:
> OK, if you are sure it is not a ISDN issue but it appears to be that the > call is set up > > Nov 26 22:10:48.504: ISDN Se0/0/0:15 Q931: RX <- ALERTING pd = 8 callref > = 0x808D > Progress Ind i = 0x8188 - In-band info or appropriate now availab > > you then get > > > Nov 26 22:10:48.548: ISDN Se0/0/0:15 Q931: TX -> DISCONNECT pd = 8 > callref = 0x008D > Cause i = 0x80AF - Resource unavailable, unspecified > > so maybe it is an IOS bug but we don't know what IOS you are running or do > we know running config or the status of any of your system. > > Just guessing here but can you complete any calls over the PSTN > connection? If so what type of calls are completed? > > > On Sun, Nov 27, 2011 at 6:36 AM, datucha123 datucha123 < > datucha...@gmail.com> wrote: > >> Bill, if you will take a dipper look at the Logs of ISDN, you will see >> the the Router send the ISD SETUP message, then received the Procceding and >> Alerting message. >> So the Voice port in operating normally. >> After the Alert message, the IP Side is starting - H245 is going for >> negotiation, and there is a problem in H323 IP Side, not in ISDN side. >> >> And I have already mentioned the Problem description in my earlier post. >> >> If there would the DSP issues, then the SETUP message will not be send >> even. >> >> On Sun, Nov 27, 2011 at 1:26 AM, Bill Lake <whl...@gmail.com> wrote: >> >>> This looks like it could be an ISDN issue: >>> >>> Is your voice-port in an active (not shut down) state? >>> >>> Do you have the proper DSP resources for your configuration? >>> >>> Check these and post your configuration if this is not the issue. >>> >>> >>> >>> On Sat, Nov 26, 2011 at 1:24 PM, datucha123 datucha123 < >>> datucha...@gmail.com> wrote: >>> >>>> That's because of Codec Problem between HQ router and the CUCM. >>>> >>>> Now look, as we know, when the CUCM sends the H323 SETUP message to GW, >>>> the GW, by default, begins the H245 Address announcement on Alert Message, >>>> and at that point the CUCM and GW have exchanged the H245 message, and the >>>> GW provides the Ring Back tone. Even when the CUCM is using the Slow Start. >>>> Whereas CUCME can detect CUCM and start the H245 only on Connect >>>> Message, while the default one idicates h245 address on Alert. CUCME IP >>>> Phones cannot provide the In Band Ring Back tones, so that CUCM needs >>>> always the Slow start to CUCME, so that CUCM will provide the Local >>>> Ringback to its IP Phones until the H245 address is received from CUCME >>>> (whereas CUCME will send the H245 address On Connect only to CUCM). >>>> >>>> Now look, as for you case, you get the error message after the Alerting >>>> Message. What does happen at that moment? GW sends the Alert message with >>>> H245 Address (and the TCS OLC negotiation begins). CUCM and GW have some >>>> problems with Codec negotation, and that's why you get that message. >>>> >>>> Try to ensure that you use the correct region to GW, and also the >>>> correct Codecs (or voice class codec) is configured on the GW. >>>> >>>> That's the problem of the Codec mismatch. >>>> >>>> >>>> >>>> >>>> >>>> >>>> On Sat, Nov 26, 2011 at 9:19 PM, Ricardo Palaver < >>>> ricardo.pala...@hotmail.com> wrote: >>>> >>>>> Hi Experts!, >>>>> >>>>> I 've already gave up to fix the problem below. >>>>> >>>>> I am calling from a HQ - phone # to PSTN (BR2) region but call >>>>> fails and it's returnning me the cause code: 0x80AF. >>>>> >>>>> In the Cisco community I found its an IOS bug, so if it is, someone >>>>> here have already faced the same issue. >>>>> >>>>> Can someone give me any idea on how to fix it ? >>>>> >>>>> >>>>> Thanks a zillions !.. have a great weekend all ! >>>>> >>>>> >>>>> >>>>> debug isdn q931 is ON. >>>>> BR2-RTR# >>>>> Nov 26 22:10:48.460: ISDN Se0/0/0:15 Q931: Applying typeplan for >>>>> sw-type 0x12 is 0x0 0x0, Calling num 2123945001 >>>>> Nov 26 22:10:48.464: ISDN Se0/0/0:15 Q931: Sending SETUP callref = >>>>> 0x008D callID = 0x800E switch = primary-net5 interface = User >>>>> Nov 26 22:10:48.464: ISDN Se0/0/0:15 Q931: TX -> SETUP pd = 8 callref >>>>> = 0x008D >>>>> Bearer Capability i = 0x8090A3 >>>>> Standard = CCITT >>>>> Transfer Capability = Speech >>>>> Transfer Mode = Circuit >>>>> Transfer Rate = 64 kbit/s >>>>> Channel ID i = 0xA98381 >>>>> Exclusive, Channel 1 >>>>> Display i = 'HQ Phone 1' >>>>> Calling Party Number i = 0x0081, '2123945001' >>>>> Plan:Unknown, Type:Unknown >>>>> Called Party Number i = 0x80, '32141891' >>>>> Plan:Unknown, Type:Unknown >>>>> Nov 26 22:10:48.500: ISDN Se0/0/0:15 Q931: RX <- CALL_PROC pd = 8 >>>>> callref = 0x808D >>>>> Channel ID i = 0xA98381 >>>>> Exclusive, Channel 1 >>>>> Nov 26 22:10:48.504: ISDN Se0/0/0:15 Q931: RX <- ALERTING pd = 8 >>>>> callref = 0x808D >>>>> Progress Ind i = 0x8188 - In-band info or appropriate now >>>>> availab >>>>> BR2-RTR#le >>>>> Nov 26 22:10:48.548: ISDN Se0/0/0:15 Q931: TX -> DISCONNECT pd = 8 >>>>> callref = 0x008D >>>>> Cause i = 0x80AF - Resource unavailable, unspecified >>>>> Nov 26 22:10:48.560: ISDN Se0/0/0:15 Q931: RX <- RELEASE pd = 8 >>>>> callref = 0x808D >>>>> Nov 26 22:10:48.564: ISDN Se0/0/0:15 Q931: TX -> RELEASE_COMP pd = 8 >>>>> callref = 0x008D >>>>> >>>>> >>>>> _______________________________________________ >>>>> For more information regarding industry leading CCIE Lab training, >>>>> please visit www.ipexpert.com >>>>> >>>>> Are you a CCNP or CCIE and looking for a job? Check out >>>>> www.PlatinumPlacement.com <http://www.platinumplacement.com/> >>>>> >>>> >>>> >>>> _______________________________________________ >>>> For more information regarding industry leading CCIE Lab training, >>>> please visit www.ipexpert.com >>>> >>>> Are you a CCNP or CCIE and looking for a job? Check out >>>> www.PlatinumPlacement.com <http://www.platinumplacement.com/> >>>> >>> >>> >> > > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > Are you a CCNP or CCIE and looking for a job? Check out > www.PlatinumPlacement.com >
_______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
