Todd,
He wouldn't have gotten connected if that was the problem. It looks more
like an authentication type problem. Just a guess...
-----Original Message-----
From: Todd Plambeck [mailto:[EMAIL PROTECTED]]
Sent: Wednesday, September 06, 2000 7:30 AM
To: [EMAIL PROTECTED]
Cc: 'Zafar'
Subject: RE: ISDN BRI dialout help
The Cisco 2503 has an S/T ISDN Interface NOT a U interface. Meaning you need
an NT-1 Adapter to connect to the ISDN line from the telco.
-----Original Message-----
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of Zafar
Sent: Wednesday, September 06, 2000 8:46 AM
To: [EMAIL PROTECTED]
Subject: ISDN BRI dialout help
Hello,
I am trying to configure ISDN BRI for dialout using 2503 but could not
connect to remote access server of the ISP. I have taken a ISDN dialup
account from ISP and it has given me "userid", passwd and dialup number. I
tried these through normal dialup (windows dun) and it connects succesfully.
Now I have following configuration for my 2503 router but this could not
connect. Please advise if I am missing something as I am new to ISDN and
doing it for the first time
!
interface BRI0
ip address negotiated
ip directed-broadcast
encapsulation ppp
no ip split-horizon
dialer idle-timeout 2147483
dialer string 12144444
dialer hold-queue 10
dialer-group 1
isdn switch-type basic-net3
ppp authentication pap
ppp pap sent-username <myusername> password <mypassword>
!
ip route 204.71.200.45 255.255.255.255 BRI0
!
dialer-list 1 protocol ip permit
when I ping 204.71.200.45 , following appears on the terminal:
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 204.71.200.45, timeout is 2 seconds:
00:58:39: %ISDN-6-LAYER2UP: Layer 2 for Interface BR0, TEI 64 changed to up
00:58:40: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up....
00:58:46: %ISDN-6-CONNECT: Interface BRI0:1 is now connected to 12144444 .
Success rate is 0 percent (0/5)
00:59:03: %ISDN-6-DISCONNECT: Interface BRI0:1 disconnected from 12144444 ,
cal
l lasted 22 seconds
00:59:03: %LINK-3-UPDOWN: Interface BRI0:1, changed state to down
00:59:05: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BR0, TEI 64 changed to
dow
sh in bri0
BRI0 is up, line protocol is up (spoofing)
Hardware is BRI
Internet address will be negotiated using IPCP
MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, loopback not set
Last input 00:00:01, output 00:00:01, output hang never
Last clearing of "show interface" counters 01:09:44
Input queue: 0/75/0 (size/max/drops); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
536 packets input, 3389 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
534 packets output, 3376 bytes, 0 underruns
0 output errors, 0 collisions, 13 interface resets
0 output buffer failures, 0 output buffers swapped out
35 carrier transitions
___________________________________
UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html
FAQ, list archives, and subscription info: http://www.groupstudy.com
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
