Hello,
I have asked my provider and they confirmed they are using pap. Now I tried again
while debugging "ppp auth" and "ppp neg". I can see a AUTH-NAK in the debug but am not
sure what does this exactly mean? Can some one please advise whats going on here and
how to fix it?
1d17h: %ISDN-6-LAYER2UP: Layer 2 for Interface BR0, TEI 64 changed to up
1d17h: ISDN BR0: TX -> SETUP pd = 8 callref = 0x4A
1d17h: Bearer Capability i = 0x8890
1d17h: Channel ID i = 0x83
1d17h: Called Party Number i = 0x80, '12144444'
1d17h: ISDN BR0: RX <- SETUP_ACK pd = 8 callref = 0xCA
1d17h: Channel ID i = 0x89
1d17h: ISDN BR0: RX <- CALL_PROC pd = 8 callref = 0xCA
1d17h: Channel ID i = 0x89
1d17h: ISDN BR0: RX <- ALERTING pd = 8 callref = 0xCA
1d17h: ISDN BR0: RX <- CONNECT pd = 8 callref = 0xCA
1d17h: Dat.e/Time i = 0x0009080B1A00
1d17h: ISDN BR0: TX -> CONNECT_ACK pd = 8 callref = 0x4A
1d17h: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up
1d17h: BR0:1 PPP: Treating connection as a callout
1d17h: BR0:1 PPP: Phase is ESTABLISHING, Active Open
1d17h: BR0:1 PPP: No remote authentication for call-out
1d17h: BR0:1 LCP: O CONFREQ [Closed] id 198 len 10
1d17h: BR0:1 LCP: MagicNumber 0xE9AF7753 (0x0506E9AF7753)
1d17h: BR0:1 LCP: I CONFREQ [REQsent] id 1 len 26
1d17h: BR0:1 LCP: AuthProto PAP (0x0304C023)
1d17h: BR0:1 LCP: MagicNumber 0xDC5B675B (0x0506DC5B675B)
1d17h: BR0:1 LCP: MRRU 1500 (0x110405DC)
1d17h: BR0:1 LCP: MultilinkShortSeq (0x1202)
1d17h: BR0:1 LCP: EndpointDisc 1 Local (0x13060150444E)
1d17h: BR0:1 LCP: O CONFREJ [REQsent] id 1 len 16
1d17h: BR0:1 LCP: MRRU 1500 (0x110405DC)
1d17h: BR0:1 LCP: MultilinkShortSeq (0x1202)
1d17h: BR0:1 LCP: EndpointDisc 1 Local (0x13060150444E)
1d17h: BR0:1 LCP: I CONFREQ [REQsent] id 2 len 14
1d17h: BR0:1 LCP: AuthPro.to PAP (0x0304C023)
1d17h: BR0:1 LCP: MagicNumber 0xDC5B675B (0x0506DC5B675B)
1d17h: BR0:1 LCP: O CONFACK [REQsent] id 2 len 14
1d17h: BR0:1 LCP: AuthProto PAP (0x0304C023)
1d17h: BR0:1 LCP: MagicNumber 0xDC5B675B (0x0506DC5B675B)
1d17h: BR0:1 LCP: TIMEout: State ACKsent
1d17h: BR0:1 LCP: O CONFREQ [ACKsent] id 199 len 10
1d17h: BR0:1 LCP: MagicNumber 0xE9AF7753 (0x0506E9AF7753)
1d17h: BR0:1 LCP: I CONFACK [ACKsent] id 199 len 10
1d17h: BR0:1 LCP: MagicNumber 0xE9AF7753 (0x0506E9AF775.3)
1d17h: BR0:1 LCP: State is Open
1d17h: BR0:1 PPP: Phase is AUTHENTICATING, by the peer
1d17h: BR0:1 PAP: O AUTH-REQ id 145 len 24 from "delta"
1d17h: BR0:1 PAP: I AUTH-NAK id 145 len 5.
1d17h: %ISDN-6-CONNECT: Interface BRI0:1 is now connected to 12144444 .
Success rate is 0 percent (0/5)
Router#
1d17h: BR0:1 PAP: O AUTH-REQ id 146 len 24 from "delta"
1d17h: BR0:1 PAP: I AUTH-NAK id 146 len 5
1d17h: BR0:1 PAP: O AUTH-REQ id 147 len 24 from "delta"
1d17h: BR0:1 PAP: I AUTH-NAK id 147 len 5
1d17h: BR0:1 LCP: I TERMREQ [Open] id 3 len 4
1d17h: BR0:1 LCP: O TERMACK [Open] id 3 len 4
1d17h: BR0:1 PPP: Phase is TERMINATING
1d17h: ISDN BR0: RX <- DISCONNECT pd = 8 callref = 0xCA
1d17h: Cause i = 0x8090 - Normal call clearing
1d17h: %ISDN-6-DISCONNECT: Interface BRI0:1 disconnected from 12144444 , call l
asted 22 seconds
1d17h: %LINK-3-UPDOWN: Interface BRI0:1, changed state to down
1d17h: BR0:1 LCP: State is Closed
1d17h: BR0:1 PPP: Phase is DOWN
1d17h: ISDN BR0: TX -> RELEASE pd = 8 callref = 0x4A
1d17h: Cause i = 0x809008 - Normal call clearing
1d17h: ISDN BR0: RX <- RELEASE_COMP pd = 8 callref = 0xCA
1d17h: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BR0, TEI 64 changed to down
---------- Original Message ----------------------------------
From: "Miller, Nathan (AZ15)" <[EMAIL PROTECTED]>
Date: Wed, 6 Sep 2000 11:39:30 -0700
>I had similar problems. I would check with your provider regarding
>authentication. It may be that they are requiring chap authentication?
>Issue "debug ppp auth" and "debug ppp neg" (assuming your IOS is relatively
>current) and look at the results when you try to connect. This may give you
>some insight into where things are failing.
>
>Good Luck!
>
>-----Original Message-----
>From: Zafar [mailto:[EMAIL PROTECTED]]
>Sent: Wednesday, September 06, 2000 6:46 AM
>To: [EMAIL PROTECTED]
>Subject: ISDN BRI dialout help
>
>
>
>Hello,
>
>I am trying to configure ISDN BRI for dialout using 2503 but could not
>connect to remote access server of the ISP. I have taken a ISDN dialup
>account from ISP and it has given me "userid", passwd and dialup number. I
>tried these through normal dialup (windows dun) and it connects succesfully.
>Now I have following configuration for my 2503 router but this could not
>connect. Please advise if I am missing something as I am new to ISDN and
>doing it for the first time
>
>
>!
>interface BRI0
> ip address negotiated
> ip directed-broadcast
> encapsulation ppp
> no ip split-horizon
> dialer idle-timeout 2147483
> dialer string 12144444
> dialer hold-queue 10
> dialer-group 1
> isdn switch-type basic-net3
> ppp authentication pap
> ppp pap sent-username <myusername> password <mypassword>
>
>!
>ip route 204.71.200.45 255.255.255.255 BRI0
>
>!
>dialer-list 1 protocol ip permit
>
>
>when I ping 204.71.200.45 , following appears on the terminal:
>
>
>Type escape sequence to abort.
>Sending 5, 100-byte ICMP Echos to 204.71.200.45, timeout is 2 seconds:
>
>00:58:39: %ISDN-6-LAYER2UP: Layer 2 for Interface BR0, TEI 64 changed to up
>00:58:40: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up....
>00:58:46: %ISDN-6-CONNECT: Interface BRI0:1 is now connected to 12144444 .
>Success rate is 0 percent (0/5)
>
>00:59:03: %ISDN-6-DISCONNECT: Interface BRI0:1 disconnected from 12144444 ,
>cal
>l lasted 22 seconds
>00:59:03: %LINK-3-UPDOWN: Interface BRI0:1, changed state to down
>00:59:05: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BR0, TEI 64 changed to
>dow
>
>sh in bri0
>
>BRI0 is up, line protocol is up (spoofing)
> Hardware is BRI
> Internet address will be negotiated using IPCP
> MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,
> reliability 255/255, txload 1/255, rxload 1/255
> Encapsulation PPP, loopback not set
> Last input 00:00:01, output 00:00:01, output hang never
> Last clearing of "show interface" counters 01:09:44
> Input queue: 0/75/0 (size/max/drops); Total output drops: 0
> Queueing strategy: weighted fair
> Output queue: 0/1000/64/0 (size/max total/threshold/drops)
> Conversations 0/1/256 (active/max active/max total)
> Reserved Conversations 0/0 (allocated/max allocated)
> 5 minute input rate 0 bits/sec, 0 packets/sec
> 5 minute output rate 0 bits/sec, 0 packets/sec
> 536 packets input, 3389 bytes, 0 no buffer
> Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
> 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
> 534 packets output, 3376 bytes, 0 underruns
> 0 output errors, 0 collisions, 13 interface resets
> 0 output buffer failures, 0 output buffers swapped out
> 35 carrier transitions
>
>
>
>
>
**NOTE: New CCNA/CCDA List has been formed. For more information go to
http://www.groupstudy.com/list/Associate-Announcement.html
_________________________________
UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html
FAQ, list archives, and subscription info: http://www.groupstudy.com
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
