Yes, i have tried this also. IT does not work again.
The thing is that it connects, and the line protocol
becomes UP also, i m using access-list with
dialer-group and i have also used floating static
routes at both end, now it should work. but it does
not work.
Shoaib
--- El Pingu wrote:
> ok...i have been through this one.
>
> my suggestion.
>
> make sure you have an access list associated with
> dialer-group 1
> and on the remote site.
>
> put a static route on both sides one on remote to
> get out and one on central
> to get you
> to remote and advertise to your network with a
> hevier weight than the IGP
> route
>
> if you want to test connectivity make the static
> more preferable ....make
> sure you have
> a interesting traffic access list or it will not
> dial.
>
>
>
>
>
> Shoaib Waqar wrote:
>
> > I am getting trouble in ISDN bri link. I have a
> > Central site Router 3640 with 12.1.8 IP/IPX plus
> IOS.
> > the route has 4 port BRI module. The remote site
> is
> > having 2503, all u know that it has 1 port BRI.
> remote
> > site is running 11.2.1 version of IOS. The call is
> > placed using simple DDR commands as:
> >
> > Cisco 3640 Router
> > =================
> > Int bri 2/0
> > ip add 130.1.1.1 255.255.255.0
> > encap ppp
> > dialer idle-timeout 300
> > dialer fast-idle 300
> > dialer string xxxxxxxx
> > dialer-group 1
> >
> > Remote site (2503):
> > ===================
> >
> > Int bri 0
> > ip add 130.1.1.2 255.255.255.0
> > encap ppp
> > dialer idle-timeout 300
> > dialer fast-idle 300
> >
> > In this scenario, a/c to customer need, the
> central
> > site is placing call.When the call has placed, and
> we
> > see the debug output, it shows all the debug of
> ppp
> > negotiations and ISDN events as correct, with the
> > install route at the end. When i run 'show isdn
> > status' it shows me all layers up with one active
> > layer 3 call also. Also 'show isdn active' gives
> me
> > successful call to remote site. So nothing seems
> to be
> > wrong with config. THE problem is that after
> > connectivity when i try to ping from central site
> the
> > remote site ip address, it times out. I took the
> 'show
> > ip route', and it gives me only connected routes
> but
> > dont show me the remote LAN network address of
> each
> > site which it should give as i m running EIGRP at
> both
> > sites. The primary link is working correctly as i
> have
> > an SCPC 128K link between the two sites as well
> and
> > showing correct routes. The switch type in
> pakistan
> > normally we use is basic-net3 (SIEMENS switch).
> Can
> > anyone plzz help me, where is the issue?? i have
> tried
> > everything, dialer profiles and all. but nothing
> seems
> > to be working, i cant ping the other side thru
> BRI.
> >
> > Shoaib
> > CCNP,MCSE
> >
> > __________________________________________________
> > Do You Yahoo!?
> > Yahoo! Auctions - buy the things you want at great
> prices
> > http://auctions.yahoo.com/
> > FAQ, list archives, and subscription info:
> http://www.groupstudy.com/list/cisco.html
> > Report misconduct and Nondisclosure violations to
> [EMAIL PROTECTED]
> FAQ, list archives, and subscription info:
> http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to
[EMAIL PROTECTED]
__________________________________________________
Do You Yahoo!?
Yahoo! Auctions - buy the things you want at great prices
http://auctions.yahoo.com/
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=2864&t=2712
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
