Sorry - missed a bit.
"Multiple Frame Established" is the most desirable state for layer 2
to be in but "TEI Assigned" is not necessarily a problem. A lot of
telcos power down the d-channel if the connection hasn't been used
for a while, the router will then report TEI Assigned but this will
go back to Multiple Frame Established when a call is attempted
inbound or outbound.
___________________________________________________
Unfortunately, "debug isdn events" is widely regarded as broken, the
information it gives can be inaccurate. Besides, if the problem isn't
simple (maybe a misconfigured telco switch at the far end - we'd need
cause codes to diagnose that) then we'd only be sending Uche back off
to do more work. I think it's better to get too much info than too
little.
Cheers
Charlie
--- Fomes Iain wrote: > Just do debug isdn
events it gives you all that in one go. When
> you do
> Show ISDN status check that you have a TEI number and the Multiple
> frame IS
> established. If not your ISDN line is knackered.
>
> regards
> Iain Fomes
> [EMAIL PROTECTED]
>
>
>
>
>
> > -----Original Message-----
> > From: Charlie Hartwell [SMTP:[EMAIL PROTECTED]]
> > Sent: 10 July 2001 09:39
> > To: [EMAIL PROTECTED]
> > Subject: Re: Still having BRI stress! [7:11653]
> >
> > The config looks fine but we will need a bit more info to help.
> The
> > error message isn't much use on it's own, so if you do "show isdn
> > status", then run "debug isdn q931", "debug isdn q921" and "debug
> > dialer", then try to make a call it should give you more
> information.
> > If you have any trouble deciphering the output then paste it all
> in
> > an email to the group and we'll try to help out some more.
> >
> > Cheers
> >
> > Charlie
> >
> > --- Uche Ishionwu wrote: > Hello,...
> > > I changed my configuration somewhat, and removed a module.
> But
> > > my cisco
> > > 2620 still wont dial out.!!.....can someone look at the
> > > configuration and
> > > the error out put and let me know what may still be the
> > > cause.(Layer 1. and
> > > layer 2. -isdn events- are ok, but theres still no connection)
> > > -Uche.
> > > config------->
> > >
> > >
> > > oks>en
> > > Password:
> > > oks#sh conf
> > > Using 1496 out of 29688 bytes
> > > !
> > > version 12.0
> > > service timestamps debug uptime
> > > service timestamps log uptime
> > > no service password-encryption
> > > !
> > > hostname oks
> > > !
> > > no logging console
> > > no logging monitor
> > > enable secret 5 $1$IU9Q$qYwqs3CXuKmsl1y1GjcM30
> > > enable password oks
> > > !
> > > username msn password 0 msn
> > > !
> > > !
> > > !
> > > !
> > > memory-size iomem 15
> > > ip subnet-zero
> > > no ip domain-lookup
> > > !
> > > isdn switch-type basic-net3
> > > !
> > > !
> > > !
> > > interface FastEthernet0/0
> > > ip address 192.168.0.2 255.255.255.0
> > > no ip directed-broadcast
> > > duplex auto
> > > speed auto
> > > !
> > > interface BRI0/0
> > > description OKS testing interface!
> > > no ip address
> > > no ip directed-broadcast
> > > encapsulation ppp
> > > dialer pool-member 1
> > > dialer pool-member 2
> > > isdn switch-type basic-net3
> > > !
> > > interface Dialer1
> > > description connected to ELSATEST
> > > ip address 192.168.8.2 255.255.255.0
> > > no ip directed-broadcast
> > > encapsulation ppp
> > > dialer pool 1
> > > dialer wait-for-carrier-time 90
> > > dialer string 00192658
> > > dialer hold-queue 10
> > > dialer-group 1
> > > ppp authentication chap
> > > !
> > > interface Dialer2
> > > ip address 192.168.8.3 255.255.255.0
> > > no ip directed-broadcast
> > > encapsulation ppp
> > > dialer pool 2
> > > dialer wait-for-carrier-time 90
> > > dialer string 00192658
> > > dialer hold-queue 10
> > > dialer-group 2
> > > no cdp enable
> > > ppp authentication chap
> > > !
> > > ip classless
> > > ip route 0.0.0.0 0.0.0.0 Dialer1
> > > no ip http server
> > > !
> > > access-list 99 permit any
> > > dialer-list 1 protocol ip permit
> > > dialer-list 1 protocol ipx permit
> > > dialer-list 2 protocol ip list 99
> > > !
> > > line con 0
> > > transport input none
> > > line aux 0
> > > line vty 0 4
> > > password uche1
> > > login
> > > !
> > > no scheduler allocate
> > > end
> > >
> > > oks#
> > >
> >
>
********************************************************************
> > > 00:13:236223201280: ISDN ERROR: Module-CCBRI Function-_Go
> > > Error-Event
> > > receive
> > > d for an unrecognized call. Data- B6, 0
> > [EMAIL PROTECTED]
> >
> > ____________________________________________________________
> > Do You Yahoo!?
> > Get your free @yahoo.co.uk address at http://mail.yahoo.co.uk
> > or your free @yahoo.ie address at http://mail.yahoo.ie
> *****************************************************************
> DISCLAIMER: The information contained in this e-mail may be
> confidential
> and is intended solely for the use of the named addressee. Access,
> copying
> or re-use of the e-mail or any information contained therein by any
> other
> person is not authorized. If you are not the intended recipient
> please
> notify us immediately by returning the e-mail to the originator.
[EMAIL PROTECTED]
____________________________________________________________
Do You Yahoo!?
Get your free @yahoo.co.uk address at http://mail.yahoo.co.uk
or your free @yahoo.ie address at http://mail.yahoo.ie
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=11669&t=11653
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
