Not that this makes sense, but the CPA (white box) routers were Cisco's
attempt to limit the usable IOS via ROM code. If you upgrade the ROM's to
the 11.0 (10c)'s, this box works just like any other 2500. Why I say all
this, is that it appears our man does not have the most basic of commands in
(boot)# mode.
.02
Phil
----- Original Message -----
From: "MADMAN"
To:
Sent: Wednesday, September 05, 2001 4:14 PM
Subject: Re: remote ios upgrade? [7:18632]
> Yes I can see the # but are you SURE you are enabled????? Your
> missing more than the copy command. Here is the output from a 2511 with
> older bootroms:
>
>
> C2511A(boot)#?
> Exec commands:
> Session number to resume
> clear Reset functions
> clock Manage the system clock
> configure Enter configuration mode
> connect Open a terminal connection
> copy Copy a config file to or from a tftp server
> debug Debugging functions (see also 'undebug')
> disable Turn off privileged commands
> disconnect Disconnect an existing network connection
> enable Turn on privileged commands
> erase Erase Flash memory
> exit Exit from the EXEC
> help Description of the interactive help system
> login Log in as a particular user
> logout Exit from the EXEC
> name-connection Name an existing network connection
> no Disable debugging functions
> pad Open a X.29 PAD connection
> ping Send echo messages
> reload Halt and perform a cold restart
> resume Resume an active network connection
> rsh Execute a remote command
> setup Run the SETUP command facility
> show Show running system information
> start-chat Start a chat-script on a line
> systat Display information about terminal lines
> telnet Open a telnet connection
> terminal Set terminal line parameters
> test Test subsystems, memory, and interfaces
> traceroute Trace route to destination
> undebug Disable debugging functions (see also 'debug')
> verify Verify checksum of a Flash file
> where List active connections
> write Write running configuration to memory, network, or
> terminal
> x3 Set X.3 parameters on PAD
>
> C2511A(boot)>sh ver
> Cisco Internetwork Operating System Software
> IOS (tm) 3000 Bootstrap Software (IGS-RXBOOT), Version 10.2(8a), RELEASE
> SOFTWAR
> E (fc1)
> Copyright (c) 1986-1995 by cisco Systems, Inc.
> Compiled Tue 24-Oct-95 15:46 by mkamson
> Image text-base: 0x01020000, data-base: 0x00001000
>
> ROM: System Bootstrap, Version 5.2(8a), RELEASE SOFTWARE
>
> C2511A uptime is 7 minutes
> System restarted by reload
> Running default software
>
> cisco 2511 (68030) processor (revision D) with 16380K/2048K bytes of
> memory.
> Processor board serial number 01782668 with hardware revision 00000000
> X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.
> 1 Ethernet/IEEE 802.3 interface.
> 2 Serial network interfaces.
> 16 terminal lines.
> 32K bytes of non-volatile configuration memory.
> 8192K bytes of processor board System flash partition 1 (Read/Write)
> 8192K bytes of processor board System flash partition 2 (Read/Write)
>
> Configuration register is 0x101
>
> Ednilson Rosa wrote:
> >
> > Hi John,
> >
> > I tried these steps but I don't have the command "copy" under my
> > "router(boot)" prompt. All I have is this:
> >
> > Router-R2(boot)#?
> > exit
> > logout
> > lock
> > show
> > terminal
> > disconnect
> > name-connection
> > resume
> > where
> > disable
> > ping
> > systat
> > traceroute
> > login
> > telnet
> > connect
> > tunnel
> > slip
> > ppp
> > pad
> > x3
> > help
> >
> > Router-R2(boot)#
> >
> > I don't even have the "config-register" command, then I guess I'll have
to
> > do a break sequence to change the config-register back to it's original
> > value.
> >
> > How can I update the flash in this case?? I tried tftp under normal
> > privileged mode but it says that flash is write protected. Is this
router
> > "non-upgradeable"?
> >
> > This is the "sh ver" result for this router:
> >
> > Router-R2(boot)#sh ver
> >
> > Cisco Internetwork Operating System Software
> > IOS (tm) 3000 Bootstrap Software (IGS-BOOT-R), Version 11.0(10c),
RELEASE
> > SOFTWA
> > RE (fc1)
> > Copyright (c) 1986-1996 by cisco Systems, Inc.
> > Compiled Fri 27-Dec-96 17:33 by loreilly
> > Image text-base: 0x01010000, data-base: 0x00001000
> >
> > ROM: System Bootstrap, Version 11.0(10c), SOFTWARE
> >
> > Router-R2 uptime is 7 minutes
> > System restarted by reload
> > Running default software
> >
> > cisco 2500 (68030) processor (revision N) with 6144K/2048K bytes of
memory.
> > Processor board ID 16316512, with hardware revision 00000000
> > X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.
> > 1 Ethernet/IEEE 802.3 interface.
> > 2 Serial network interfaces.
> > 32K bytes of non-volatile configuration memory.
> > 8192K bytes of processor board System flash (Read/Write)
> >
> > Configuration register is 0x2101
> >
> > Router-R2(boot)#
> >
> > ----- Original Message -----
> > From: "John Neiberger"
> > To:
> > Sent: Wednesday, September 05, 2001 1:58 PM
> > Subject: Re: remote ios upgrade? [7:18632]
> >
> > Sure, but it requires some precautions. This can be hazardous since
> > it's very easy to lock yourself out of the remote router. Double check
> > these instructions before you use them. I accept no responsibility for
> > my typos or omissions. ;-)
> >
> > 1. Verify that the router has sufficient total flash memory to hold the
> > image
> > 2. Enter config mode and set the default gateway using the ip
> > default-gateway command. Make the gateway the ip address of the nearest
> > upstream neighbor on that particular link.
> > 3. Type "config-reg 0x101" so that the router will boot from ROM.
> > 4. Supposedly, if the router has more than one serial port, you're
> > supposed to shutdown the ones that won't be used here but I'm not sure
> > if that's true or not.
> > 5. Save the config and reload the router
> > 6. Re-establish your telnet session once the router is done rebooting.
> > It will boot to the "router(boot)>" prompt.
> > 7. Put the router in privileged (enable) mode
> > 8. Issue the "copy tftp flash" command with the necessary parameters
> > 9. After transfer is complete, go to config mode and type "config-reg
> > 0x2102" and exit config mode.
> > 10. DO NOT SAVE THE CONFIG AT THIS POINT! This will write a boot ROM
> > version of your config to NVRAM....a "bad" thing.
> > 11. Reload the router. Do *NOT* reply "yes" when it asks if you want
> > to save the config!
> > 12. Re-establish telnet session. Remove ip default-gateway command
> > and do a no shutdown on those interfaces mentioned earlier.
> > 13. Save your config to NVRAM.
> >
> > I know, that's a lot of work but you have to be careful. You might
> > want to try this on routers that aren't too far away first, just in case
> > you need to make a special trip.
> >
> > Good luck,
> > John
> >
> > >>> "Jerry Deer" 9/5/01 10:31:26 AM >>>
> > Is there anyway to upgrade a 2500 router ios using a frame relay
> > connection?
> --
> David Madland
> Sr. Network Engineer
> CCIE# 2016
> Qwest Communications Int. Inc.
> [EMAIL PROTECTED]
> 612-664-3367
>
> "Emotion should reflect reason not guide it"
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=18783&t=18632
--------------------------------------------------
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]