hi ... if you do a "show traffic-shape" what does the "byte limit" count say for each VC....
also what does show traffic-shape stats ...say also with GTS you should have 3 value`s not four i.e (bit rate) (burst size) (excess) traffic-shape rate 64000 5000 5000 what the fourth value in your command doing ?... hth steve hth steve >From: "Joseba Izaga" >Reply-To: "Joseba Izaga" >To: [EMAIL PROTECTED] >Subject: Re: Traffic-rate shape [7:32072] >Date: Wed, 16 Jan 2002 09:08:16 -0500 > >This is the configuration I have in all 17204s. As you can see, I am using >GTS, but is not working, it is not limiting to 64 or 32. > >interface Serial1 > description WII-Enlace-Sebaco > bandwidth 256 > no ip address > no ip directed-broadcast > encapsulation frame-relay IETF > no keepalive > no fair-queue >! >interface Serial1.1 multipoint > description MP-Sebaco > ip address 132.1.21.1 255.255.255.0 > no ip directed-broadcast > no arp frame-relay > frame-relay map ip 132.1.21.2 515 > frame-relay map ip 132.1.21.3 519 > frame-relay map ip 132.1.21.4 523 >! >interface Serial1.2 point-to-point > bandwidth 64 > ip unnumbered FastEthernet0 > no ip directed-broadcast > no arp frame-relay > traffic-shape rate 64000 8000 8000 1000 > no cdp enable > frame-relay interface-dlci 516 >! >interface Serial1.3 point-to-point > bandwidth 64 > ip unnumbered FastEthernet0 > no ip directed-broadcast > no arp frame-relay > traffic-shape rate 32000 8000 8000 1000 > no cdp enable > frame-relay interface-dlci 520 > >Regards, > >Joseba Izaga > >----- Original Message ----- >From: "mike" >To: "Joseba Izaga" ; >Sent: Tuesday, January 15, 2002 6:17 PM >Subject: Re: Traffic-rate shape [7:32072] > > > > It should work using 12.0 on a 1720 router. We use 12.0.7T on our >1720s, > > and traffic shape using map-classes and priority queueing > > > > What does your config look like, what commands are you using to verify > > traffic shaping is/isn't on? > > > > > > ----- Original Message ----- > > From: "Joseba Izaga" > > To: > > Sent: Tuesday, January 15, 2002 7:38 PM > > Subject: Re: Traffic-rate shape [7:32072] > > > > > > > I already did a frame-relay traffic shaping and limit with CIR, but >did > > not > > > function. > > > > > > What else can I do instead of upgrading the IOS? > > > > > > ----- Original Message ----- > > > From: "Steven A. Ridder" > > > To: > > > Sent: Tuesday, January 15, 2002 2:22 PM > > > Subject: Re: Traffic-rate shape [7:32072] > > > > > > > > > > Try upgrading the IOS or do CBWFQ or frame-relay traffic shaping and > > limit > > > > with CIR. Create a map class and add map class to subinterface. > > > > > > > > > > > > ""Joseba Izaga"" wrote in message > > > > [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > > > > > Hi, > > > > > > > > > > I have a 1720 with 2 WIC-1T. I have 2 frame-relay radiomodem >connected > > > to > > > > > each > > > > > port. Each port has 2 sub-interfaces. > > > > > > > > > > What I need is to limit the bandwidth on the sub-interface to 64k. > > > > > > > > > > Right now I am using the command traffic-rate shape 64000 on a >CISCO > > > 2620 > > > > and > > > > > it is working good, but not on the 1720. > > > > > > > > > > The 1720 has 12.0 IOS version. > > > > > > > > > > So, why the 1720 is not limiting the bandwitdh? > > > > > > > > > > Or, there is another way to limit the bandwitdh? > > > > > > > > > > Regards, > > > > > > > > > > Joseba Izaga _________________________________________________________________ Send and receive Hotmail on your mobile device: http://mobile.msn.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=32163&t=32072 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]