On a similar subject - Is it possible to use a destination-pattern of for instance 70 (no wild cards or anything) and still get it to work. The reason for this is to allow users to phone the operator of another site using just the trunk code and a "0". As it is the router comes back with something like 'no number to dial' even when used with prefix 70, because there is nothing except the destination-pattern.
Basically the destination-pattern needs to be the full number. Hope I've explained myself well enough. Please excuse the VoIP newbie. Gaz ""Steven A. Ridder"" wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > I'd do some dubugs like "debug voice ccapi inout" to see what numbers are > being sent to the PBX and across the IP call leg (on both sides). > > I'd also try to validate your dialing plan by doing a "show dialplan number > (DN you wish to test)" to see whci dial-peer the router thinks it should be > using. > > Finally check for codec mismatches, missing routes in the routing table > etc.. > > > > ""Firesox"" wrote in message > [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > > Site A > > voice-card 1 > > ! > > ip subnet-zero > > no ip source-route > > no ip finger > > ! > > lane client flush > > ! > > ! > > controller T1 1/0 > > framing esf > > linecode b8zs > > ds0-group 1 timeslots 1-24 type e&m-wink-start > > cas-custom 1 > > ! > > ! > > voice-port 1/0:1 > > operation 4-wire > > ! > > ! > > dial-peer voice 1 pots > > destination-pattern 370.. > > port 1/0:1 > > prefix 370 > > ! > > dial-peer voice 10 voip > > destination-pattern 79.. > > session target ipv4:1.1.1.2 > > ! > > dial-peer voice 2 pots > > destination-pattern 374.. > > port 1/0:1 > > prefix 374 > > ! > > ! > > interface FastEthernet0/0 > > bandwidth 10000 > > ip address x.x.x.x x.x.x.x > > speed 10 > > full-duplex > > ! > > interface Serial0/0 > > bandwidth 1536 > > ip address 2.2.2.2 255.255.255.252 > > no fair-queue > > down-when-looped > > ! > > ip classless > > ip route 0.0.0.0 0.0.0.0 Serial0/0 > > **************************************** > > Site B > > > > voice-card 1 > > ! > > ip subnet-zero > > no ip source-route > > ! > > lane client flush > > ! > > ! > > controller T1 1/0 > > framing esf > > linecode b8zs > > ds0-group 1 timeslots 1-24 type e&m-wink-start > > cas-custom 1 > > ! > > ! > > voice-port 1/0:1 > > operation 4-wire > > ! > > ! > > dial-peer voice 1 pots > > destination-pattern 79.. > > port 1/0:1 > > prefix 79 > > ! > > dial-peer voice 10 voip > > destination-pattern 370.. > > session target ipv4:2.2.2.2 > > ! > > dial-peer voice 11 voip > > destination-pattern 374.. > > session target ipv4:2.2.2.2 > > ! > > ! > > interface FastEthernet0/0 > > ip address x.x.x.x x.x.x.x > > duplex auto > > speed auto > > ! > > interface Serial0/0 > > bandwidth 1544 > > ip address 1.1.1.2 255.255.255.252 > > no ip mroute-cache > > no fair-queue > > ! > > ip classless > > ip route 0.0.0.0 0.0.0.0 1.1.1.1 > > no ip http server Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=48951&t=48709 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
