I'm not sure I understand the question. If the question is, if there's a number 335, and I tell the router 355 is over on a different router, is that a valid dial-peer (355). If that's the question, yes it is.
Did I understand the question correctly? ""Gaz"" wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > On a similar subject - Is it possible to use a destination-pattern of for > instance 70 (no wild cards or anything) and still get it to work. The reason > for this is to allow users to phone the operator of another site using just > the trunk code and a "0". > As it is the router comes back with something like 'no number to dial' even > when used with prefix 70, because there is nothing except the > destination-pattern. > > Basically the destination-pattern needs to be the full number. > > Hope I've explained myself well enough. > > Please excuse the VoIP newbie. > > > Gaz > > > ""Steven A. Ridder"" wrote in message > [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > > I'd do some dubugs like "debug voice ccapi inout" to see what numbers are > > being sent to the PBX and across the IP call leg (on both sides). > > > > I'd also try to validate your dialing plan by doing a "show dialplan > number > > (DN you wish to test)" to see whci dial-peer the router thinks it should > be > > using. > > > > Finally check for codec mismatches, missing routes in the routing table > > etc.. > > > > > > > > ""Firesox"" wrote in message > > [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > > > Site A > > > voice-card 1 > > > ! > > > ip subnet-zero > > > no ip source-route > > > no ip finger > > > ! > > > lane client flush > > > ! > > > ! > > > controller T1 1/0 > > > framing esf > > > linecode b8zs > > > ds0-group 1 timeslots 1-24 type e&m-wink-start > > > cas-custom 1 > > > ! > > > ! > > > voice-port 1/0:1 > > > operation 4-wire > > > ! > > > ! > > > dial-peer voice 1 pots > > > destination-pattern 370.. > > > port 1/0:1 > > > prefix 370 > > > ! > > > dial-peer voice 10 voip > > > destination-pattern 79.. > > > session target ipv4:1.1.1.2 > > > ! > > > dial-peer voice 2 pots > > > destination-pattern 374.. > > > port 1/0:1 > > > prefix 374 > > > ! > > > ! > > > interface FastEthernet0/0 > > > bandwidth 10000 > > > ip address x.x.x.x x.x.x.x > > > speed 10 > > > full-duplex > > > ! > > > interface Serial0/0 > > > bandwidth 1536 > > > ip address 2.2.2.2 255.255.255.252 > > > no fair-queue > > > down-when-looped > > > ! > > > ip classless > > > ip route 0.0.0.0 0.0.0.0 Serial0/0 > > > **************************************** > > > Site B > > > > > > voice-card 1 > > > ! > > > ip subnet-zero > > > no ip source-route > > > ! > > > lane client flush > > > ! > > > ! > > > controller T1 1/0 > > > framing esf > > > linecode b8zs > > > ds0-group 1 timeslots 1-24 type e&m-wink-start > > > cas-custom 1 > > > ! > > > ! > > > voice-port 1/0:1 > > > operation 4-wire > > > ! > > > ! > > > dial-peer voice 1 pots > > > destination-pattern 79.. > > > port 1/0:1 > > > prefix 79 > > > ! > > > dial-peer voice 10 voip > > > destination-pattern 370.. > > > session target ipv4:2.2.2.2 > > > ! > > > dial-peer voice 11 voip > > > destination-pattern 374.. > > > session target ipv4:2.2.2.2 > > > ! > > > ! > > > interface FastEthernet0/0 > > > ip address x.x.x.x x.x.x.x > > > duplex auto > > > speed auto > > > ! > > > interface Serial0/0 > > > bandwidth 1544 > > > ip address 1.1.1.2 255.255.255.252 > > > no ip mroute-cache > > > no fair-queue > > > ! > > > ip classless > > > ip route 0.0.0.0 0.0.0.0 1.1.1.1 > > > no ip http server Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=48984&t=48709 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]