Some other things to consider. Is the bottom clean? It the 2000 rpm while tied to the dock?
Josh On Jul 28, 2014 12:16 AM, "Bill Hoyne via CnC-List" <cnc-list@cnc-list.com> wrote: > Hi All, > I have a Max Prop of unknown diameter (forgot to measure when I had the > boat out of the water). I also have a Volvo Penta 2003 and when I run the > engine in idle I get 3000+ RPM,s but when I run it in gear I only get > 1900-2000 RPM's. I suspect the pitch is a little high. ( A dripless seal, > new shaft and cutless bering were installed last year and in the process > the max-prop was taken off and may not have been installed with the > original specs of which I don't have from the PO.) My question in does > anybody out there know what the X,Y values should be for a typical C&C > MKII? I would like a starting point to compare what is in the prop now and > where I should head to. The other question is can I do thin in the water or > do I need to haul the boat? > Thanks, > Bill > > > > *Bill Hoyne* > Mithrandir > '74 C&C35 MkII > in Victoria,BC > > > > On Jul 24, 2014, at 5:01 PM, Chuck S via CnC-List <cnc-list@cnc-list.com> > wrote: > > As stated before, I like to follow the manufacturer's recommendation and > use Lubriplate 130 AA for MaxProp. It is a grease that works well on > bronze parts. The base is the same for Lewmar winch grease. I opened our > MaxProp this winter after 7 years on the boat, and found the metal clean, > bright gold in color, and shiny. No oxidation at all. Thanks, Lubriplate. > > > > Chuck > Resolute > 1990 C&C 34R > Broad Creek, Magothy River, Md > > ------------------------------ > *From: *"CNC boat owners, cnc-list" <cnc-list@cnc-list.com> > *To: *"CNC boat owners, cnc-list" <cnc-list@cnc-list.com> > *Sent: *Thursday, July 24, 2014 10:23:50 AM > *Subject: *Stus-List Prop Grease > > Subject change. > > Has anyone tried Krazy Grease, a waterproof grease in cartridges that is > advertised as being the greatest thing since short skirts? > > Might be good on MaxProps etc. > > See www.krazygrease.com > > Rich Knowles > INDIGO LF38 > Halifax, NS. > > > > _______________________________________________ > This List is provided by the C&C Photo Album > > Email address: > CnC-List@cnc-list.com > To change your list preferences, including unsubscribing -- go bottom of > page at: > http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com > > > _______________________________________________ > This List is provided by the C&C Photo Album > > Email address: > CnC-List@cnc-list.com > To change your list preferences, including unsubscribing -- go bottom of > page at: > http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com > > > > _______________________________________________ > This List is provided by the C&C Photo Album > > Email address: > CnC-List@cnc-list.com > To change your list preferences, including unsubscribing -- go bottom of > page at: > http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com > > >
_______________________________________________ This List is provided by the C&C Photo Album Email address: CnC-List@cnc-list.com To change your list preferences, including unsubscribing -- go bottom of page at: http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com